Linux may be used without MMU on atmel SoCs, fix debug in this configuration.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Move debug-macro.S from include/mach/ to include/debug where all other common
debug macros are.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

SoC identification code, kernel uncompress and low level
debugging routines update.
On SAMA5D4, DBGU is at another address AT91_BASE_DBGU2 so another
round of detection is needed. We also had to differentiate with
SAMA5D3 SoC family and rename some variables.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

we will select now the DBGU used by the soc at Kconfig level

For the DEBUG_LL and early_printk this will allow to select which DBGU to use
this will also allow to select them when multiple SOC are enabled
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use.  Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.

This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: Nnicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: NKevin Hilman <khilman@ti.com>

to make the soc base specified at runtime instead of compiled time
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.

This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.

Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: NJeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Tested-by: NKevin Hilman <khilman@deeprootsystems.com>

Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.

NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:

$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
	arch/arm/*/include/*/debug-macro.S
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.

These changes are:
      * The system peripheral I/O region we remap has increased from
        0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
      * The increased I/O region forces changes to entry-macro.S and
        debug-macro.S due to ARM's limited immediate offset addressing
        modes.
      * Maximum number of GPIO banks increases to 5.
      * 2 MMC controllers so the board-setup code needs to specify which
        controller it wishes to use when calling at91_add_device_mmc().

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the drivers (and other files) which include the
hardware headers.  This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).

The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h.  Renamed it to at91_pdc.h
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>