Both iPAQs h3600 and h3100 share the same control
GPIOs for PCMCIA, so driver can be reused.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for "Power" and "Action" (joystick center) buttons -
the only buttons on iPaq h3100/h3600 connected to GPIOs
(other buttons are controlled by microcontroller)
Also remove setting PWER for wakeup on Power button press -
gpio-keys driver will handle it.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

After a code reorganization and following split, there's some #includes
now unused. Clean them up and sort remaining alphabetticaly where possible.

Compile tested.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Correct boilerplates after files split. Also shorten them a bit - use
standart GPL wording (as per http://lkml.org/lkml/2007/5/1/220) and
drop changelog, which only entry about h3800 support and abstracted
EGPIOs is just confusing now, as both of these features are gone.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Split common h3600.c into three separate files: h3100.c, h3600.c and
h3xxx.c (the latter contains common code for h3100/h3600)
Copyright boilerplates and #includes are copied intact and will be
cleaned up later.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Combine both headers into one, rename to h3xxx.h and change all
users accordingly.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As all existing code was converted to gpiolib, drop no more
used pre-gpiolib (bit-shifted) GPIO definintions.
Supply new gpiolib-friendly definitions for GPIOs which
don't have them yet.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

After conversion to gpiolib there's still some GPIOs left, that get
configured in *_mach_init() as outputs (using direct operations
on GPCR/GPDR registers), but otherwise unused. These GPIOs are mainly
sound related and should be configured by corresponding driver once
it is written.

Drop this initialisation and configure all GPIOs as input.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As all the remaining users of these definitions
(in pcmcia/sa1100_h3600 driver) were converted to gpio_to_irq(),
they can be safely removed.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As all users of assign_h3600_egpio now converted to gpiolib, we
can safely remove all assign_h3600_egpio handling code and
definitions.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use of gpio_request/gpio_free in some callbacks may look ugly, but
corresponding drivers (sa1100_serial and sa1100_fb) don't provide (yet)
init/exit hooks and registering these gpios in *_mach_init is also
not possible, because htc-gpio driver starts a bit later...
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It will be used for future conversion of assign_h3600_egpio calls to
gpiolib.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

h3100 and h3600 have different sets of LCD-controlling gpios,
which mapped to the same "abstracted" EGPIO.
As we plan to get rid of those abstracted egpios completely, we
need to separate these helper functions.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert all operations with GPLR/GPCR/GPSR to gpiolibs calls.
Also change all IRQ_GPIO* to gpio_to_irq(*GPIO*)
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

sa1100_fb driver handles this
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PM_SUSPEND, PM_RESUME and machine_is_h3xxx() are not used anywhere in
kernel (checked with git grep), so it's safe to remove them.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

IRDA is handled by separate sa1100-ir driver and has
nothing to do with sa1100_serial
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The rtc-sa1100 driver takes care of this.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

No point calling sa1100_register_uart_fns early - these aren't
used until late in the boot sequence.  Also convert to gpiolib
support.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Only register devices if we have platform data for those which require
platform data.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Limit number of per cpu TSC sync messages
  x86: dumpstack, 64-bit: Disable preemption when walking the IRQ/exception stacks
  x86: dumpstack: Clean up the x86_stack_ids[][] initalization and other details
  x86, cpu: mv display_cacheinfo -> cpu_detect_cache_sizes
  x86: Suppress stack overrun message for init_task
  x86: Fix cpu_devs[] initialization in early_cpu_init()
  x86: Remove CPU cache size output for non-Intel too
  x86: Minimise printk spew from per-vendor init code
  x86: Remove the CPU cache size printk's
  cpumask: Avoid cpumask_t in arch/x86/kernel/apic/nmi.c
  x86: Make sure we also print a Code: line for show_regs()

* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, msr, cpumask: Use struct cpumask rather than the deprecated cpumask_t
  x86, cpuid: Simplify the code in cpuid_open
  x86, cpuid: Remove the bkl from cpuid_open()
  x86, msr: Remove the bkl from msr_open()
  x86: AMD Geode LX optimizations
  x86, msr: Unify rdmsr_on_cpus/wrmsr_on_cpus

Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix a section mismatch in arch/x86/kernel/setup.c
  x86: Fixup last users of irq_chip->typename
  x86: Remove BKL from apm_32
  x86: Remove BKL from microcode
  x86: use kernel_stack_pointer() in kprobes.c
  x86: use kernel_stack_pointer() in kgdb.c
  x86: use kernel_stack_pointer() in dumpstack.c
  x86: use kernel_stack_pointer() in process_32.c

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  include/linux/compiler-gcc4.h: Fix build bug - gcc-4.0.2 doesn't understand __builtin_object_size
  x86/alternatives: No need for alternatives-asm.h to re-invent stuff already in asm.h
  x86/alternatives: Check replacementlen <= instrlen at build time
  x86, 64-bit: Set data segments to null after switching to 64-bit mode
  x86: Clean up the loadsegment() macro
  x86: Optimize loadsegment()
  x86: Add missing might_fault() checks to copy_{to,from}_user()
  x86-64: __copy_from_user_inatomic() adjustments
  x86: Remove unused thread_return label from switch_to()
  x86, 64-bit: Fix bstep_iret jump
  x86: Don't use the strict copy checks when branch profiling is in use
  x86, 64-bit: Move K8 B step iret fixup to fault entry asm
  x86: Generate cmpxchg build failures
  x86: Add a Kconfig option to turn the copy_from_user warnings into errors
  x86: Turn the copy_from_user check into an (optional) compile time warning
  x86: Use __builtin_memset and __builtin_memcpy for memset/memcpy
  x86: Use __builtin_object_size() to validate the buffer size for copy_from_user()

Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
  x86, apic: Enable lapic nmi watchdog on AMD Family 11h
  x86: Remove unnecessary mdelay() from cpu_disable_common()
  x86, ioapic: Document another case when level irq is seen as an edge
  x86, ioapic: Fix the EOI register detection mechanism
  x86, io-apic: Move the effort of clearing remoteIRR explicitly before migrating the irq
  x86: SGI UV: Map low MMR ranges
  x86: apic: Print out SRAT table APIC id in hex
  x86: Re-get cfg_new in case reuse/move irq_desc
  x86: apic: Remove not needed #ifdef
  x86: io-apic: IO-APIC MMIO should not fail on resource insertion
  x86: Remove asm/apicnum.h
  x86: apic: Do not use stacked physid_mask_t
  x86, apic: Get rid of apicid_to_cpu_present assign on 64-bit
  x86, ioapic: Use snrpintf while set names for IO-APIC resourses
  x86, apic: Use PAGE_SIZE instead of numbers
  x86: Remove local_irq_enable()/local_irq_disable() in fixup_irqs()
  x86: Use EOI register in io-apic on intel platforms
  x86: Force irq complete move during cpu offline
  x86: Remove move_cleanup_count from irq_cfg
  x86, intr-remap: Avoid irq_chip mask/unmask in fixup_irqs() for intr-remapping
  ...

Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (35 commits)
  sched, cputime: Introduce thread_group_times()
  sched, cputime: Cleanups related to task_times()
  Revert "sched, x86: Optimize branch hint in __switch_to()"
  sched: Fix isolcpus boot option
  sched: Revert 498657a4
  sched, time: Define nsecs_to_jiffies()
  sched: Remove task_{u,s,g}time()
  sched: Introduce task_times() to replace task_{u,s}time() pair
  sched: Limit the number of scheduler debug messages
  sched.c: Call debug_show_all_locks() when dumping all tasks
  sched, x86: Optimize branch hint in __switch_to()
  sched: Optimize branch hint in context_switch()
  sched: Optimize branch hint in pick_next_task_fair()
  sched_feat_write(): Update ppos instead of file->f_pos
  sched: Sched_rt_periodic_timer vs cpu hotplug
  sched, kvm: Fix race condition involving sched_in_preempt_notifers
  sched: More generic WAKE_AFFINE vs select_idle_sibling()
  sched: Cleanup select_task_rq_fair()
  sched: Fix granularity of task_u/stime()
  sched: Fix/add missing update_rq_clock() calls
  ...

Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (470 commits)
  x86: Fix comments of register/stack access functions
  perf tools: Replace %m with %a in sscanf
  hw-breakpoints: Keep track of user disabled breakpoints
  tracing/syscalls: Make syscall events print callbacks static
  tracing: Add DEFINE_EVENT(), DEFINE_SINGLE_EVENT() support to docbook
  perf: Don't free perf_mmap_data until work has been done
  perf_event: Fix compile error
  perf tools: Fix _GNU_SOURCE macro related strndup() build error
  trace_syscalls: Remove unused syscall_name_to_nr()
  trace_syscalls: Simplify syscall profile
  trace_syscalls: Remove duplicate init_enter_##sname()
  trace_syscalls: Add syscall_nr field to struct syscall_metadata
  trace_syscalls: Remove enter_id exit_id
  trace_syscalls: Set event_enter_##sname->data to its metadata
  trace_syscalls: Remove unused event_syscall_enter and event_syscall_exit
  perf_event: Initialize data.period in perf_swevent_hrtimer()
  perf probe: Simplify event naming
  perf probe: Add --list option for listing current probe events
  perf probe: Add argv_split() from lib/argv_split.c
  perf probe: Move probe event utility functions to probe-event.c
  ...

Merge branch 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
  tracing: Separate raw syscall from syscall tracer
  ring-buffer-benchmark: Add parameters to set produce/consumer priorities
  tracing, function tracer: Clean up strstrip() usage
  ring-buffer benchmark: Run producer/consumer threads at nice +19
  tracing: Remove the stale include/trace/power.h
  tracing: Only print objcopy version warning once from recordmcount
  tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
  ring-buffer: Move access to commit_page up into function used
  tracing: do not disable interrupts for trace_clock_local
  ring-buffer: Add multiple iterations between benchmark timestamps
  kprobes: Sanitize struct kretprobe_instance allocations
  tracing: Fix to use __always_unused attribute
  compiler: Introduce __always_unused
  tracing: Exit with error if a weak function is used in recordmcount.pl
  tracing: Move conditional into update_funcs() in recordmcount.pl
  tracing: Add regex for weak functions in recordmcount.pl
  tracing: Move mcount section search to front of loop in recordmcount.pl
  tracing: Fix objcopy revision check in recordmcount.pl
  tracing: Check absolute path of input file in recordmcount.pl
  tracing: Correct the check for number of arguments in recordmcount.pl
  ...

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing: Fix trace_marker output
  tracing: Fix event format export
  tracing: Fix return value of tracing_stats_read()

Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix spurious irq seqfile conversion
  genirq: switch /proc/irq/*/spurious to seq_file
  irq: Do not attempt to create subdirectories if /proc/irq/<irq> failed
  irq: Remove unused debug_poll_all_shared_irqs()
  irq: Fix docbook comments
  irq: trivial: Fix typo in comment for #endif

Merge branch 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softlockup: Fix hung_task_check_count sysctl

Merge branch 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  signal: Print warning message when dropping signals
  signal: Fix alternate signal stack check

Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
  rcu: Make RCU's CPU-stall detector be default
  rcu: Add expedited grace-period support for preemptible RCU
  rcu: Enable fourth level of TREE_RCU hierarchy
  rcu: Rename "quiet" functions
  rcu: Re-arrange code to reduce #ifdef pain
  rcu: Eliminate unneeded function wrapping
  rcu: Fix grace-period-stall bug on large systems with CPU hotplug
  rcu: Eliminate __rcu_pending() false positives
  rcu: Further cleanups of use of lastcomp
  rcu: Simplify association of forced quiescent states with grace periods
  rcu: Accelerate callback processing on CPUs not detecting GP end
  rcu: Mark init-time-only rcu_bootup_announce() as __init
  rcu: Simplify association of quiescent states with grace periods
  rcu: Rename dynticks_completed to completed_fqs
  rcu: Enable synchronize_sched_expedited() fastpath
  rcu: Remove inline from forward-referenced functions
  rcu: Fix note_new_gpnum() uses of ->gpnum
  rcu: Fix synchronization for rcu_process_gp_end() uses of ->completed counter
  rcu: Prepare for synchronization fixes: clean up for non-NO_HZ handling of ->completed counter
  rcu: Cleanup: balance rcu_irq_enter()/rcu_irq_exit() calls
  ...

Merge branch 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ratelimit: Make suppressed output messages more useful
  printk: Remove ratelimit.h from kernel.h
  ratelimit: Fix/allow use in atomic contexts
  ratelimit: Use per ratelimit context locking