virtio has been so far used only in the context of virtualization,
and the virtio Kconfig was sourced directly by the relevant arch
Kconfigs when VIRTUALIZATION was selected.

Now that we start using virtio for inter-processor communications,
we need to source the virtio Kconfig outside of the virtualization
scope too.

Moreover, some architectures might use virtio for both virtualization
and inter-processor communications, so directly sourcing virtio
might yield unexpected results due to conflicting selections.

The simple solution offered by this patch is to always source virtio's
Kconfig in drivers/Kconfig, and remove it from the appropriate arch
Kconfigs. Additionally, a virtio menu entry has been added so virtio
drivers don't show up in the general drivers menu.

This way anyone can use virtio, though it's arguably less accessible
(and neat!) for virtualization users now.

Note: some architectures (mips and sh) seem to have a VIRTUALIZATION
menu merely for sourcing virtio's Kconfig, so that menu is removed too.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

pit_clockevent wants to replaced in the argument of the callback
function as well.

Reported-by; Ingo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The comment is outdated, wikipedia now has six translations of the cpuid
page.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This patch fixes three typos I've accidentally spotted.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (one was already fixed)

Also removes a long-unused #define and an extraneous semicolon.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

We switch back from using vmcall in 091ebf07
because it was unreliable under kvm, but I missed one (rarely-used) place.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

The Host used to create some page tables for the Guest to use at the
top of Guest memory; it would then tell the Guest where this was.  In
particular, it created linear mappings for 0 and 0xC0000000 addresses
because lguest used to switch to its real page tables quite late in
boot.

However, since d50d8fe1 Linux initialized boot page tables in
head_32.S even before the "are we lguest?" boot jump.  So, now we can
simplify things: the Host pagetable code assumes 1:1 linear mapping
until it first calls the LHCALL_NEW_PGTABLE hypercall, which we now do
before we reach C code.

This also means that the Host doesn't need to know anything about the
Guest's PAGE_OFFSET.  (Non-Linux guests might not even have such a
thing).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Commit 63ab25eb (kgdbts: unify/generalize gdb breakpoint adjustment)
introduced a compile regression on sparc.

kgdbts.c: In function 'check_and_rewind_pc':
kgdbts.c:307: error: implicit declaration of function 'instruction_pointer_set'

Simply add the correct macro definition for instruction pointer on the
Sparc architecture.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>

We can map the vDSO straight from kernel data, saving a few page
allocations.  As an added bonus, the deleted code contained a memory
leak.
Signed-off-by: NAndy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/2c4ed5c2c2e93603790229e0c3403ae506ccc0cb.1311277573.git.luto@mit.eduSigned-off-by: NH. Peter Anvin <hpa@zytor.com>

The machinery for __ARCH_HAS_CLOCKSOURCE_DATA assumed a file in
asm-generic would be the default for architectures without their own
file in asm/, but that is not how it works.

Replace it with a Kconfig option instead.

Link: http://lkml.kernel.org/r/4E288AA6.7090804@zytor.comSigned-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Luck <tony.luck@intel.com>

An implementation of a code generator for BPF programs to speed up packet
filtering on PPC64, inspired by Eric Dumazet's x86-64 version.

Filter code is generated as an ABI-compliant function in module_alloc()'d mem
with stackframe & prologue/epilogue generated if required (simple filters don't
need anything more than an li/blr).  The filter's local variables, M[], live in
registers.  Supports all BPF opcodes, although "complicated" loads from negative
packet offsets (e.g. SKF_LL_OFF) are not yet supported.

There are a couple of further optimisations left for future work; many-pass
assembly with branch-reach reduction and a register allocator to push M[]
variables into volatile registers would improve the code quality further.

This currently supports big-endian 64-bit PowerPC only (but is fairly simple
to port to PPC32 or LE!).

Enabled in the same way as x86-64:

	echo 1 > /proc/sys/net/core/bpf_jit_enable

Or, enabled with extra debug output:

	echo 2 > /proc/sys/net/core/bpf_jit_enable
Signed-off-by: NMatt Evans <matt@ozlabs.org>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yet another variant of the Dell Latitude series which requires
reboot=pci.

From the E5420 bug report by Daniel J Blueman:

> The E6420 is affected also (same platform, different casing and
> features), which provides an external confirmation of the issue; I can
> submit a patch for that later or include it if you prefer:
> http://linux.koolsolutions.com/2009/08/04/howto-fix-linux-hangfreeze-during-reboots-and-restarts/Reported-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>

Rebooting on the Dell E5420 often hangs with the keyboard or ACPI
methods, but is reliable via the PCI method.

[ hpa: this was deferred because we believed for a long time that the
  recent reshuffling of the boot priorities in commit
  660e34ce fixed this platform.
  Unfortunately that turned out to be incorrect. ]
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Link: http://lkml.kernel.org/r/1305248699-2347-1-git-send-email-daniel.blueman@gmail.comSigned-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>

copy_from_user_nmi() is used in oprofile and perf. Moving it to other
library functions like copy_from_user(). As this is x86 code for 32
and 64 bits, create a new file usercopy.c for unified code.
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110607172413.GJ20052@erda.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

This patch:

 - fixes typos in comments and clarifies the text
 - renames obscure p4_event_alias::original and ::alter members to
   ::original and ::alternative as appropriate
 - drops parenthesis from the return of p4_get_alias_event()

No functional changes.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Link: http://lkml.kernel.org/r/20110721160625.GX7492@sunSigned-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This array is read-only. Make it explicit by marking as const.
Signed-off-by: NGreg Dietsche <Gregory.Dietsche@cuw.edu>
Link: http://lkml.kernel.org/r/1309482653-23648-1-git-send-email-Gregory.Dietsche@cuw.eduSigned-off-by: NIngo Molnar <mingo@elte.hu>

The EFI specification requires that callers of the time related
runtime functions serialize with other CMOS accesses in the
kernel, as the EFI time functions may choose to also use the
legacy CMOS RTC.

Besides fixing a latent bug, this is a prerequisite to safely
enable the rtc-efi driver for x86, which ought to be preferred
over rtc-cmos on all EFI platforms.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Acked-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Cc: <mjg@redhat.com>
Link: http://lkml.kernel.org/r/4E257E33020000780004E319@nat28.tlf.novell.comSigned-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Matthew Garrett <mjg@redhat.com>

With CPU hotplug, there is a theoretical race between other CMOS
(namely RTC) accesses and those done in the SMP secondary
processor bringup path.

I am unware of the problem having been noticed by anyone in practice,
but it would very likely be rather spurious and very hard to reproduce.
So to be on the safe side, acquire rtc_lock around those accesses.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/4E257AE7020000780004E2FF@nat28.tlf.novell.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

With the write lock path simply subtracting RW_LOCK_BIAS there
is, on large systems, the theoretical possibility of overflowing
the 32-bit value that was used so far (namely if 128 or more
CPUs manage to do the subtraction, but don't get to do the
inverse addition in the failure path quickly enough).

A first measure is to modify RW_LOCK_BIAS itself - with the new
value chosen, it is good for up to 2048 CPUs each allowed to
nest over 2048 times on the read path without causing an issue.
Quite possibly it would even be sufficient to adjust the bias a
little further, assuming that allowing for significantly less
nesting would suffice.

However, as the original value chosen allowed for even more
nesting levels, to support more than 2048 CPUs (possible
currently only for 64-bit kernels) the lock itself gets widened
to 64 bits.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4E258E0D020000780004E3F0@nat28.tlf.novell.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Rather than having two functionally identical implementations
for 32- and 64-bit configurations, use the previously extended
assembly abstractions to fold the rwsem two implementations into
a shared one.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4E258DF3020000780004E3ED@nat28.tlf.novell.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Rather than having two functionally identical implementations
for 32- and 64-bit configurations, extend the existing assembly
abstractions enough to fold the two rwlock implementations into
a shared one.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4E258DD7020000780004E3EA@nat28.tlf.novell.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Btrfs needs to be able to control how filemap_write_and_wait_range() is called
in fsync to make it less of a painful operation, so push down taking i_mutex and
the calling of filemap_write_and_wait() down into the ->fsync() handlers.  Some
file systems can drop taking the i_mutex altogether it seems, like ext3 and
ocfs2.  For correctness sake I just pushed everything down in all cases to make
sure that we keep the current behavior the same for everybody, and then each
individual fs maintainer can make up their mind about what to do from there.
Thanks,
Acked-by: NJan Kara <jack@suse.cz>
Signed-off-by: NJosef Bacik <josef@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

its first argument is const char * and it's really not modified...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

1. support brownstone
2. support mmc
3. support basic filesystem and language
4. remove dynamic_debug, since too many log during access sd
Signed-off-by: NZhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NMark F. Brown <mark.brown314@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

As suggested by Arnd, move platform data to include/linux/platform_data
in order to improve build coverage for the driver.
Signed-off-by: NZhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Update MMP2 platform code to "sdhci-pxav3", following the driver rename.
Signed-off-by: NZhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NMark F. Brown <mark.brown314@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

sdhci-pltfm driver for PXAV3 SoCs, such as MMP2.
Signed-off-by: NZhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NPhilip Rakity <prakity@marvell.com>
Acked-by: NMark F. Brown <mark.brown314@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The rcu callback sn_irq_info_free() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(sn_irq_info_free).
Signed-off-by: NLai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Video input mux settings for tvp7002 and imager inputs were swapped.
Comment was correct.

Tested on EVM with tvp7002 input.
Signed-off-by: NJon Povey <jon.povey@racelogic.co.uk>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Cc: stable@kernel.org
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Avoid NULL dereference of irq_alloc_generic_chip return in low
memory conditions.
Signed-off-by: NTodd Poynor <toddpoynor@google.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Now that 1b3f2a72 is in, it is very
important that the below lying comment be removed! :-)
Signed-off-by: NBorislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20110718191054.GA18359@liondog.tnicAcked-by: NAndy Lutomirski <luto@mit.edu>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

This shift instruction appears to be shifting in the wrong direction.
Without this change, my SparcStation-20MP hangs just after bringing up
the second CPU:

Entering SMP Mode...
Starting CPU 2 at f02b4e90
Brought up 2 CPUs
Total of 2 processors activated (99.52 BogoMIPS).
   *** stuck ***
Signed-off-by: NWill Simoneau <simoneau@ele.uri.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function declaration differs between file: dma.c and file:dma.h
and SPARSE (Documentation/sparse.txt) gives error messages

All dma channels are members of 'enum dma_ch' and not 'unsigned int'
Please have a look at channel definitions in:
arch/arm/mach-s3c64xx/include/mach/dma.h
arch/arm/plat-samsung/include/plat/s3c-dma-pl330.h
arch/arm/mach-s3c2410/include/mach/dma.h
So all arguments should be of type 'enum dma_ch'
Signed-off-by: NSangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NTodd Poynor <toddpoynor@google.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Commit 234b6ced

   clocksource: convert ARM 32-bit up counting clocksources

broke the build for ixp4xx and made big endian operation impossible.
This commit restores the original behaviour.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
[ Thomas says that we might want to have generic BE accessor functions
  to the MMIO clock source, but that hasn't happened yet, so in the
  meantime this seems to be the short-term fix for the particular
  problem - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The code in arch/mips/kernel/i8259.c still hasn't been converted to
using struct syscore_ops instead of a sysdev for resume and shutdown.
As a result, this code doesn't build any more after suspend, resume
and shutdown callbacks have been removed from struct sysdev_class.
Fix this problem by converting i8259.c to using syscore_ops.
Reported-and-tested-by: NRoland Vossen <rvossen@broadcom.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NRalf Baechle <ralf@linux-mips.org>