So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Just to catch bugs when changing mac80211.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
and I want to kill netdev->priv later, I decided to convert all the direct
reference of netdev->priv first.

In this driver, I don't simply use netdev_priv() to replace netdev->priv.

The reason is:
Pointer netdev->priv was changed in this driver, but it shouldn't.
Because the memory was allocated when alloc_netdev() and netdev->priv
should always point to that memory.

So I use netdev->ml_priv to replace netdev->priv.
After replacing, both ai and ai->wifidev->ml_priv point to the same memory.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes mesh point operation (thanks to YanBo for pointing
out the problem): make mesh point interfaces start beaconing when
they come up and configure the RX filter in mesh mode so that mesh
beacons and action frames are received.  Add mesh point to the check
in ath5k_add_interface.  Tested with multiple AR5211 cards.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adjusts ath5k's signal quality reporting taking into
consideration received beacons at an RSSI of 35 should indicate
you can use of 54 Mbps on a single stream card (all ath5k cards)
reliably.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adjusts ath9k's signal quality reporting taking into
consideration received beacons at an RSSI of 45 should indicate
you can use of MCS 15 rate (144 Mbps) reliably on dual stream card.
Keep in mind mac80211 does not yet have aggregation fixed but this
should still provide more accurate results.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we officially are supporting ath5k I can do this
at work hours.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change adds short slot handling for 8187B variant of rtl8187 chips.
Some things to note about changes done:
* Values used are chosen to met 802.11-2007 spec. This raised a question
  about SIFS value used with 8187L: 0x22 (34) doesn't match any spec
  value. For now just don't change 8187L, but is something to be
  looked at.
* On 8187B, the location of EIFS register is at the same place as BRSR+1
  of struct rtl818x_csr. Unfortunately there is no clean way to
  accomodate 8187B differences currently, just use address of BRSR+1 and
  comment about it. The same thing happens for Ack timeout register,
  that is on CARRIER_SENSE_COUNTER location of 8187L. The eifs and ack
  timeout values are in units of 4us. All these registers information
  was gathered from references being the vendor gpl driver and 8180
  datasheet, unfortunately there is no information about this on 8187B
  datasheet. Also the ack timeout value was inspired by the same
  calculation as done on rt2x00.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates 8187L handling for short slot after "mac80211: fix short
slot handling". For 8187B, there was no handling done for short slot
timing so nothing done, support for it will come in a following patch.
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for AP mode. This involves:
- enablement in ath5k_beacon_config -- initialize beacon timer
- add AP to the supported modes in ath5k_add_interface
- handle beacon change even for AP in ath5k_config_interface
- remove useless test for IBSS in ath5k_beacon_update

Note that it doesn't enable the AP mode for the driver. It must
be enabled by NL80211_IFTYPE_AP bit added to interface_modes.

v2:
Fixed opmode constant (IEEE80211_ to NL80211_)
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sorry about that, for some reason I didn't notice that I'd
left some unused variables in there.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HT handling has the following deficiencies, which I've
(partially) fixed:
 * it always uses the AP info even if there is no AP,
   hence has no chance of working as an AP
 * it pretends to be HW config, but really is per-BSS
 * channel sanity checking is left to the drivers
 * it generally lets the driver control too much

HT enabling is still wrong with this patch if you have more than
one virtual STA mode interface, but that never happens currently.
Once WDS, IBSS or AP/VLAN gets HT capabilities, it will also be
wrong, see the comment in ieee80211_enable_ht().

Additionally, this fixes a number of bugs:
 * mac80211: ieee80211_set_disassoc doesn't notify the driver any
             more since the refactoring
 * iwl-agn-rs: always uses the HT capabilities from the wrong stuff
               mac80211 gives it rather than the actual peer STA
 * ath9k: a number of bugs resulting from the broken HT API

I'm not entirely happy with putting the HT capabilities into
struct ieee80211_sta as restricted to our own HT TX capabilities,
but I see no cleaner solution for now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Probably bugs I added.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This exports the local HT capabilities in nl80211.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I've come to think that not providing sequence numbers for
the normal STA mode case was a mistake, at least two drivers
now had to implement code they wouldn't otherwise need, and
I believe at76_usb and adm8211 might be broken.

This patch makes mac80211 assign a sequence number to all
those frames that need one except beacons. That means that
if a driver only implements modes that do not do beaconing
it need not worry about the sequence number.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch entitled "[PATCH] p54: Fix sparse warnings" added the __le16
variable rx_mtu to struct bootrec, but it could equally well be placed
in the struct bootrec_desc, which overlays the 'data' section of bootrec.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Limit the number of "expensive" rfkill workqueue operations per second, in
order to not hog system resources too much when faced with a rogue source
of rfkill input events.

The old rfkill-input code (before it was refactored) had such a limit in
place.  It used to drop new events that were past the rate limit.  This
behaviour was not implemented as an anti-DoS measure, but rather as an
attempt to work around deficiencies in input device drivers which would
issue multiple KEY_FOO events too soon for a given key FOO (i.e. ones that
do not implement mechanical debouncing properly).

However, we can't really expect such issues to be worked around by every
input handler out there, and also by every userspace client of input
devices.  It is the input device driver's responsability to do debouncing
instead of spamming the input layer with bogus events.

The new limiter code is focused only on anti-DoS behaviour, and tries to
not lose events (instead, it coalesces them when possible).

The transmitters are updated once every 200ms, maximum.  Care is taken not
to delay a request to _enter_ rfkill transmitter Emergency Power Off (EPO)
mode.

If mistriggered (e.g. by a jiffies counter wrap), the code delays processing
*once* by 200ms.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rfkill_resume() would always restore the rfkill controller state to its
pre-suspend state.

Now that we know when we are under EPO, kick the rfkill controller to
SOFT_BLOCKED state instead of to its pre-suspend state when it is resumed
while EPO mode is active.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add of software-based sanity to rfkill and rfkill-input so that it can
reproduce what hardware-based EPO switches do, blocking all transmitters
and locking down any further attempts to unblock them until the switch is
deactivated.

rfkill-input is responsible for issuing the EPO control requests, like
before.

While an rfkill EPO is active, all transmitters are locked to one of the
BLOCKED states and all attempts to change that through the rfkill API
(userspace and kernel) will be either ignored or return -EPERM errors.

The lock will be released upon receipt of EV_SW SW_RFKILL_ALL ON by
rfkill-input, or should modular rfkill-input be unloaded.

This makes rfkill and rfkill-input extend the operation of an existing
wireless master kill switch to all wireless devices in the system, even
those that are not under hardware or firmware control.

Since the above is the expected operational behavior for the master rfkill
switch, the EPO lock functionality is not optional.

Also, extend rfkill-input to allow for three different behaviors when it
receives an EV_SW SW_RFKILL_ALL ON input event.  The user can set which
behavior he wants through the master_switch_mode parameter:

master_switch_mode = 0: EV_SW SW_RFKILL_ALL ON just unlocks rfkill
controller state changes (so that the rfkill userspace and kernel APIs can
now be used to change rfkill controller states again), but doesn't change
any of their states (so they will all remain blocked).  This is the safest
mode of operation, as it requires explicit operator action to re-enable a
transmitter.

master_switch_mode = 1: EV_SW SW_RFKILL_ALL ON causes rfkill-input to
attempt to restore the system to the state before the last EV_SW
SW_RFKILL_ALL OFF event, or to the default global states if no EV_SW
SW_RFKILL_ALL OFF ever happened.   This is the recommended mode of
operation for laptops.

master_switch_mode = 2: tries to unblock all rfkill controllers (i.e.
enable all transmitters) when an EV_SW SW_RFKILL_ALL ON event is received.
This is the default mode of operation, as it mimics the previous behavior
of rfkill-input.

In order to implement these features in a clean way, the entire event
handling of rfkill-input was refactored into a single worker function.

Protection against input event DoS (repeatedly firing rfkill events for
rfkill-input to process) was removed during the code refactoring.  It will
be added back in a future patch.

Note that with these changes, rfkill-input doesn't need to explicitly
handle any radio types for which KEY_<radio type> or SW_<radio type> events
do not exist yet.

Code to handle EV_SW SW_{WLAN,WWAN,BLUETOOTH,WIMAX,...} was added as it
might be needed in the future (and its implementation is not that obvious),
but is currently #ifdef'd out to avoid wasting resources.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Export the the global switch states to rfkill-input.  This is needed to
properly implement KEY_* handling without disregarding the initial state.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apparently, many applications don't expect to get EAGAIN from fd read/write
operations, since POSIX doesn't mandate it.

Use mutex_lock_killable instead of mutex_lock_interruptible, which won't
cause issues.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.

No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.

Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Never actually used.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up a number of things:
 * the unusable definition of the HT capabilities/HT information
   information elements
 * variable names that are hard to understand
 * mac80211: move ieee80211_handle_ht to ht.c and remove the unused
             enable_ht parameter
 * mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht
 * mac80211: fix bug with casting the result of ieee80211_bss_get_ie
             to an information element _contents_ rather than the
             whole element, add size checking (another out-of-bounds
             access bug fixed!)
 * mac80211: remove some unused return values in favour of BUG_ON
             checking
 * a few minor other things
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch was made on behalf of Johannes request.
"mac80211 and IEEE80211_CONF_SHORT_SLOT_TIME"

Of course, bss_info_changed provides some more useful data.
e.g.: basic_rates, dtim_period, beacon_int and maybe even more.
Everything can be hooked up if it's necessary.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a typo in mac80211_hwsim.c:
use HWSIM_STA_MAGIC in hwsim_check_sta_magic() and hwsim_set_sta_magic()
instead of HWSIM_VIF_MAGIC.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch refactors rxon time command. It removes the usage of union tsf
in favor of u64 value and hopefully makes code more readable.  There are
no functional changes in this patch.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch selects a valid antennae upon rate scale init. This solves a
SYSASSERT complaining that the driver is setting a non valid antenna in
the LQ CMD.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds ability to configure initial calibration set. Not all HW
supported by iwlwifi use the same calibration set, XTAL is one example.
Some clean ups are also included in this patch.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unused definition of struct sta_attribute
in net/mac80211/ieee80211_i.h.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes mac80211 handle short slot requests from the AP
properly. Also warn about uses of IEEE80211_CONF_SHORT_SLOT_TIME
and optimise out the code since it cannot ever be hit anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The antenna gain isn't exactly configurable, despite the belief of
some unnamed individual who thinks that the EEPROM might influence
it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Warn when ieee80211_hw_config returns an error, it shouldn't
happen; remove a number of printks that would happen in such
a case and one printk that is user-triggerable.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This isn't used by anyone, if we ever need it we can add
it back, until then it's useless.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Nothing very interesting, some checkpatch inspired stuff,
some other things.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These parameters shouldn't be configurable via debugfs, if they
need to be configurable nl80211 support has to be added, if not
then they don't need to be writable here either.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Javier Cardona <javier@cozybit.com>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This code uses static variables and thus cannot be kept.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>