Add DT binding documentation for HDMI Connector.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Add DT binding documentation for DVI Connector.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Add DT binding documentation for Analog TV Connector.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>

Add device tree bindings for OMAP Display Subsystem for the following
SoCs: OMAP2, OMAP3, OMAP4.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for panel-sony-acx565akm
Signed-off-by: NSebastian Reichel <sre@debian.org>
[tomi.valkeinen@ti.com: some modifications]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for connector-analog-tv.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for hdmi-connector.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for encoder-tpd12s015.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for connector-dvi.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for encoder-tfp410.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for panel-dsi-cm.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add the code to make the DSI driver work with device tree on OMAP3 and
OMAP4.

A minor hack is needed at the moment in the DSI driver: the DSS driver
needs to know the ID number of a DSI device, as clocks are routed in
different ways to the DSI devices. At the moment we don't have any
proper way to manage this, so this patchs adds a simple lookup table
that is used to deduce the ID from the DSI device's base address.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support to VENC.

In contrast to non-DT version, the DT version gets the invert-polarity
and connector type via venc's endpoint, not from the connector.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support to HDMI driver. The only thing needed for DT support here
is the of_match_table.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support to DISPC. Only thing needed here is the of_match_table.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add DT support for DSS. Contrary to the non-DT version, the DSS in DT
mode contains DPI and SDI outputs, which better reflects the hardware.
The non-DT code will be removed after all boards have been converted to
DT, so there's no need to change the non-DT code to act the same way.

The code for DPI and SDI needs to be refined later to make it possible
to add multiple DPI ports. For now, handling just a single DPI port is
enough for all the boards.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

The regulator names used for DSS components are somewhat ugly for DT
use. As we're just adding DT support, it's simple to change the
regulator names.

This patch makes the DSS driver get the regulators with somewhat cleaner
names when bootin with DT. For example, this allows us to define HDMI's
VDDA regulator in the DT data as:

vdda-supply = <...>;

instead of

vdda_hdmi_dac-supply = <...>;
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add helpers to get ports and endpoints from DT data.

These helpers parse v4l2 style ports and endpoints, but compared to the
v4l2 helpers, these allow iterating ports and endpoints separately.

This is a temporary solution until we get generic code to parse the
ports and endpoints.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Improve the search for the default display in two ways:
* compare the given display name to the display's alias
* if no display name is given, look for "display0" DT alias
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Separate the code for finding the default display into a function for
clarity and to make it easier to extend it in the future.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

We currently create a "displayX" style alias name for all displays,
using a number that is incremented for each registered display. With the
new DSS device model there is no clear order in which the displays are
registered, and thus the numbering is somewhat random.

This patch improves the behavior for DT case so that if the displays
have been assigned DT aliases, those aliases will be used as DSS
aliases.

This means that "display0" is always the one specified in the DT alias,
and thus display0 can be used as default display in case the user didn't
specify a default display.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

Add support to get the label (i.e. a "nickname") for a display from the
DT data. If there is no label defined, use the display's alias (e.g.
'display0') as a name.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>

As there is no common panel framework in the kernel, we have OMAP
specific panel drivers. However, the DT data should be generic. This
brings the issue that some other platform could use the same panels, and
would need to create a driver with the same 'compatible' string as the
OMAP driver.

In the long run, we have to get a common panel framework. For the time
being, this patch solves the issue:

At early boot time, we go through the DT nodes looking for the panels
the kernel supports for OMAP. For each found node, the 'compatible'
string is prepended with "omapdss,", i.e. "sony,acx565akm" becomes
"omapdss,sony,acx565akm". The OMAP display drivers all have "omapdss,"
at the beginning of their compatible field.

This allows us to have generic DT data, but OMAP specific display
drivers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

The OMAP display architecture requires a bunch of platform devices which
are not created via .dts (for now). We also need to pass a few function
pointers and the DSS hardware version from the arch code to omapdss
driver.

This patch adds omapdss_init_of() function, called from board-generic at
init time, which handles those tasks.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes for ARM platforms.  Most are fixes for DTS
  files, mostly from DT conversion on OMAP which is still finding a few
  issues here and there.

  There's a couple of small stale code removal patches that we usually
  queue for the next release instead, but they seemed harmless enough to
  bring in now.

  Also, a fix for backlight on some PXA platforms, and a cache
  configuration fix for Tegra, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
  MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
  ARM: tegra: only run PL310 init on systems with one
  ARM: tegra: Add head numbers to display controllers
  ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
  ARM: tegra: fix RTC0 alias for Cardhu
  ARM: dove: dt: revert PMU interrupt controller node
  Documentation: dt: OMAP: Update Overo/Tobi
  ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
  ARM: dts: omap3-tobi: Use the correct vendor prefix
  ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
  ARM: OMAP2+: Remove legacy macros for zoom platforms
  ARM: OMAP2+: Remove MACH_NOKIA_N800
  ARM: dts: N900: add missing compatible property
  ARM: dts: N9/N950: fix boot hang with 3.14-rc1
  ARM: OMAP1: nokia770: enable tahvo-usb
  ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
  ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
  ARM: dts: omap3-gta04: Fix mmc1 properties.
  ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
  ARM: OMAP2+: add missing ARCH_HAS_OPP
  ...

Pull regulator fixes from Mark Brown:
 "Mostly unexciting driver fixes, plus one fix to lower the severity of
  the log message when we don't use an optional regulator - the fixes
  for ACPI system made this come up more often and it was correctly
  observed that it was causing undue concern for users"

* tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: max14577: Fix invalid return value on DT parse success
  regulator: core: Change dummy supplies error message to a warning
  regulator: s5m8767: Add missing of_node_put
  regulator: s5m8767: Use of_get_child_by_name
  regulator: da9063: Bug fix when setting max voltage on LDOs 5-11

Pull timer fix from Thomas Gleixner:
 "Serialize the registration of a new sched_clock in the currently ARM
  only generic sched_clock facilty to avoid sched_clock havoc"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched_clock: Prevent callers from seeing half-updated data

Pull x86 fixes from Thomas Gleixner:

 - a bugfix which prevents a divide by 0 panic when the newly introduced
   try_msr_calibrate_tsc() fails

 - enablement of the Baytrail platform to utilize the newfangled msr
   based calibration

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: tsc: Add missing Baytrail frequency to the table
  x86, tsc: Fallback to normal calibration if fast MSR calibration fails

Pull irq fixes from Thomas Gleixner:
 "Another four fixlets to tame the ARM orion irq chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: orion: Fix getting generic chip pointer.
  irqchip: orion: clear stale interrupts in irq_startup
  irqchip: orion: use handle_edge_irq on bridge irqs
  irqchip: orion: clear bridge cause register on init

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for reported issues for 3.14-rc4

  The majority of these are for USB gadget, phy, and musb driver issues.
  And there's a few new device ids thrown in for good measure"

* tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: need to mask when writting endptflush and endptprime
  usb: musb: correct use of schedule_delayed_work()
  usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP
  usb: gadget: fix NULL pointer dereference
  usb: gadget: printer: using gadget_is_otg to check otg support at runtime
  phy: let phy_provider_register be the last step in registering PHY
  phy-core: Don't allow building phy-core as a module
  phy-core: Don't propagate -ENOSUPP from phy_pm_runtime_get_sync to caller
  phy-core: phy_get: Leave error logging to the caller
  phy,phy-bcm-kona-usb2.c: Add dependency on HAS_IOMEM
  usb: musb: correct use of schedule_delayed_work()
  usb: musb: do not sleep in atomic context
  USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8
  USB: EHCI: add delay during suspend to prevent erroneous wakeups
  usb: gadget: bcm63xx_udc: fix build failure on DMA channel code
  usb: musb: do not sleep in atomic context
  usb: gadget: s3c2410_udc: Fix build error
  usb: musb: core: Fix remote-wakeup resume
  usb: musb: host: Fix SuperSpeed hub enumeration
  usb: musb: fix obex in g_nokia.ko causing kernel panic

Pull TTY revert from Greg KH:
 "Here is a single commit, a revert of a sysfs file change that ended up
  breaking a userspace tool"

* tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "tty: Set correct tty name in 'active' sysfs attribute"

Pull staging tree fix from Greg KH:
 "Here is a single android driver fix for 3.14-rc4 that fixes a reported
  problem in the binder driver"

* tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: binder: Fix death notifications

Pull char/misc fix from Greg KH:
 "Here is a single commit, to fix a reported problem in the mei driver"

* tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: set client's read_cb to NULL when flow control fails

Add myself as an additional maintainer for the Broadcom mobile
SoCs.
Signed-off-by: NMatt Porter <mporter@linaro.org>
Acked-by: NChristian Daudt <bcm@fixthebug.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge remote-tracking branches 'regulator/fix/da9063', 'regulator/fix/max14577' and 'regulator/fix/s5m8767' into regulator-linus

This reverts commit d8a5dc30.

This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect.  Either way, this needs
to be reverted until it is all figured out.
Reported-by: NJosh Boyer <jwboyer@fedoraproject.org>
Reported-by: NRay Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull scheduler fixes from Ingo Molnar:
 "Misc fixlets: a fair number of them resulting from the new
  SCHED_DEADLINE code"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Remove useless dl_nr_total
  sched/deadline: Test for CPU's presence explicitly
  sched: Add 'flags' argument to sched_{set,get}attr() syscalls
  sched: Fix information leak in sys_sched_getattr()
  sched,numa: add cond_resched to task_numa_work
  sched/core: Make dl_b->lock IRQ safe
  sched/core: Fix sched_rt_global_validate
  sched/deadline: Fix overflow to handle period==0 and deadline!=0
  sched/deadline: Fix bad accounting of nr_running

Pull perf fixes from Ingo Molnar:
 "Misc fixlets from all around the place"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/uncore: Fix IVT/SNB-EP uncore CBOX NID filter table
  perf/x86: Correctly use FEATURE_PDCM
  perf, nmi: Fix unknown NMI warning
  perf trace: Fix ioctl 'request' beautifier build problems on !(i386 || x86_64) arches
  perf trace: Add fallback definition of EFD_SEMAPHORE
  perf list: Fix checking for supported events on older kernels
  perf tools: Handle PERF_RECORD_HEADER_EVENT_TYPE properly
  perf probe: Do not add offset twice to uprobe address
  perf/x86: Fix Userspace RDPMC switch
  perf/x86/intel/p6: Add userspace RDPMC quirk for PPro