Remove the unneeded struct device *dev argument from dwc2_hcd_init()
and dwc2_hcd_remove(), and pass in the value through the hsotg->dev
member instead
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Previously, when an active urb was dequeued, its host channel would
not always be released. There is some special handling for this in
dwc2_hc_chhltd_intr_dma, but when it was the last urb/qtd in its qh, a
safeguard in dwc2_hc_n_intr would short-circuit and prevent the regular
interrupt handlers from running, without releasing the channel.

This is easily triggered when using a 3G modem using the option driver.
Opening and closing any ttyUSBx device will eat up a host channel that
is forever unusable from that point on.
Signed-off-by: NMatthijs Kooijman <matthijs@stdin.nl>
[paulz@synopsys.com: fixed comment style and added a couple of NULL checks]
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When pMgmt->uScanChannel > pDevice->byMaxChannel scanning ends
but no SIOCGIWSCAN(scan done) message is sent. This section of code is
duplicate of that in WLAN_CMD_SCAN_END which sends scan done.
So remove it and jump eCommandState to WLAN_CMD_SCAN_END.

Increment uScanChannel on !ChannelValid.

At WLAN_CMD_SCAN_END reset uScanChannel to 0 when done.
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This macro relies on a local variable having a specific name. Replace
it with a new helper function, s626_mc_disable().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This macro relies on a local variable having a specific name. Replace
it with a new helper function, s626_mc_enable().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the unused s626_ai_rinsn() function is commented out with
/* ... */ on every line of the function. Remove those by using an

This block will be removed once it is determined that it really
is not needed.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reformat the whitespace in the comedi_lrange table and use the
BIP_RANGE() macro instead of generic RANGE() macro.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Factor the code that handles the counter interrupt out of s626_irq_handler().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Factor the code that handles the end of scan interrupt out of
s626_irq_handler().

Remove the printk noise when cfc_write_to_buffer() fails. The user
can't do anything about it anyway.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comedi_async pointer is used a number of times in this function.
For aesthetic reasons, use a local variable for the pointer.

Also, since was already have a pointer to the "cmd" use that in the
for loop instead of s->async->cmd (or even async->cmd).
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comedi_subdevice in this function is actually the dev->read_subdev
that was initialized during the attach of the board. Use that instead
of accessing the dev->subdevices array directly.

Also, get the comedi_cmd used in s626_irq_handler() when the function
is first entered.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Factor the code that checks and handles the dio interrupts out of
s626_irq_handler().

This allows reducing the number of indents in the code and makes it
easier to follow.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver has three dio subdevices, each with 16 channels. These
subdevices use hardware registers that are spaced 0x10 bytes apart
for each "group" of 16 channels.

Create new macros to get the correct addresses for each register
based on the dio "group". Use the s->private (void *) to hold the
"group" number to use in the subdevice functions.

This allows removing struct dio_private and all its uses. It also
removes the ugly casts used to get the register address.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The comedi core expects the (*insn_read) operations to read insn->n
values and return the number of values actually read.

Make this function work like the core expects.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a simple true/false test, return bool instead of int.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The (*do_cmdtest) already validated the cmd sources so the default
cases in the switch() statements can never happen.

Preclear to trigger bits and change the switch() statements to simple
if() tests to set the bits.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the kernel noise in labpc_common_attach() as well as a couple
obvious comments.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

DMA support only works if an interrupt is available.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the dma channel is not available this driver will still work
with interrupts for the analog input subdevice command support.

In addition, only dma channels 1 and 3 are valid for the ISA
devices.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the interrupt is not available this driver will still work
with command support disabled for the analog input subdevice.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure labpc_counter_set_mode() was successfull and return any
errno back to the caller.

For the if/else conditions that either load the counter of just set
the mode, use a common error patch to check for the error.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetic reasons, move the labpc_counter_load() function so
it's by the labpc_counter_set_mode() function.

Update all the labpc_counter_load() calls so that the I8254_MODE*
enums are used instead of the open coded values.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce labpc_counter_set_mode() which is a wrapper around the
i8254_set_mode() helpers to program the 8254 timers. Use the new
function instead of directly writing to the timer mode register
with a "magic" number.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Let the compiler figure out if this function should be inlined.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For aesthetic reasons, move a couple of the #defines in this file
so that the register map defines are first.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename the register map defines to better match the National
Instruments Register-Level Programming Manual for the labpc.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up the multi-line comments at the beginning of the file
so that they follow the CodingStyle.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix a checkpatch.pl warning about a line over 80 characters.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to wait for the a/d conversion to
complete.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to read the a/d conversion result
from the fifo.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to set the COMMAND6_REG.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The labpc_cancel() function can be used by the labpc_ai_insn_read() and
labpc_ai_cmd() functions to disable the ai subdevice.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce a helper function to set the channel and gain bits in the
COMMAND1_REG.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Determine the chan, range, and aref when the variables are declared.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Determine the scan_mode early and get the proper chanspec so that
the chan, range, and aref can be determined when the variables are
declared.

labpc_ai_chanlist_invalid() checks that all the range and aref values
in the chanlist are the same so, for consistency, use the same chanspec
used to get the chan.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ai subdevice (*do_cmd) pointer is only initialized if the
driver has successfully requested the interrupt. The extra test
in labpc_ai_cmd() is not necessary.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In labpc_ai_cmd(), move the declaration of the local variable
'irq_flags' to remove the need for the extra #ifdef/#endif.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the DRV_NAME define and just open code the string in the
comedi_driver and pci_driver declarations.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In labpc_common_attach(), initialize the dev->board_name early and
use that instead of DRV_NAME when allocating the resources.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In labpc_common_attach(), move the declaration of the local variable
'dma_flags' to remove the need for the extra #ifdef/#endif.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>