Since turning on idle-halt in commit fe46aa67 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: NMichel Marti <mma@objectxp.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add nodes for the SRAM available on atmel SoCs
For the at91sam9260 and the at91sam9g20, address mirroring is used to create a
single contiguous SRAM range instead of declaring two separate banks.

Also remove leftover TODOs in the sam9g45 file
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: correct at91sam9rl sram size => 0x10000]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add a DT node for the TRNG (True Random Number Generator) block.

Keep this block enabled as it does not depend on any external connection,
and thus should be available on all boards.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Add ISI (Image Sensor Interface) DT node + pinctrl definition.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add GPBR (General Purpose Block Backup Registers) nodes.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

at91sam926x, at91sam9g45 and at91sam9rl SoCs all have at least one RTT
block.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add rtc node to both the at91sam9g45 SoC family and the at91sam9m10g45ek board.
Signed-off-by: NErik van Luijk <evanluijk@interact.nl>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Declare the SCKC (Slow Clock Configuration) block and its clks.
Make use of the clk32k clk instead of slow_osc where appropriate.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The G45 and 9263 SoCs has two identical ram controller, that are defined as a
single node, with two reg cells.

The proper way to support such a case is to have two separate DT nodes.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Define the at91sam9g45 clocks in the SoC dtsi file.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Fixes the compatible string, adds the pinmuxing for the ADC pins.

Also, removes atmel,adc-use-external-triggers as it is not possible to remove it
unless redefining the whole adc node
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Remove the properties that are not used anymore by the at91_adc driver.

Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add the "atmel,nand-has-dma" property to NAND node for SoC that
can use the DMA to perform NAND accesses.
Use of this property was added in 1b719265
(mtd: atmel_nand: add a new dt binding item for nand dma support).
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NBoris BREZILLON <b.brezillon@overkiz.com>

Set default watchdog options in every SoC compatible with the sam9 watchdog.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Add PWM device node for AT91 series SoC.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

pinctrl-names property was missing from mmc nodes.

Cc: <stable@vger.kernel.org> #3.11+
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NBo Shen <voice.shen@atmel.com>

Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch adds pinctrl configurations for at91 Timer Counter blocks.
These pin definitions can be referenced by "atmel,tcb-pwm" devices to
setup pins as PWM output for instance.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: switch to pinctrl pre-processor macros]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch updates the in-kernel dts files according to the latest cpus
and cpu bindings updates for ARM.
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

to prepare the switch to the macro.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Tested-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
[wenyou.yang@atmel.com: add spi nodes for sam9260, sam9263, sam9g45 and sam9n12]
[wenyou.yang@atmel.com: remove spi property "cs-gpios" to the board dts files]
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add DMA resources to MCI nodes.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: correct 9g45, 9n12 dma phandle name]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Moving to generic DMA DT binding involves to set #dma-cells to 2.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add the ADC low and high resolution configuration and which one to use.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add pinctrl support for SSC on AT91 dtsi files.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: split dtsi and driver changes]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reluctantly-acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Change the value of status to disabled to keep the consistent
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Add mci controller nodes to atmel SOCs.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

as we just use the rts and not the rts & cts for rs485
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

USART are the full pin uart
DBGU the debug Unit
UART the two pin uart
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Tested on an at91sam9260 board (evk-pro3).
Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add atmel-ssc for device tree support

Match "atmel,at91rm9200-ssc" for using pdc for data transfer
Match "atmel,at91sam9g45-ssc" for using dma for data transfer
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>