This change moves flags and state into the same cacheline.  The reason for
this change is because both are frequently read around the same time and
infrequently written.  By combining them into the same cacheline this
should help to reduce memory utilization.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The semaphore can be in locked state upon driver load, particularly
on 82598 if a machine is rebooted due to panic and the semaphore was
acquired just prior to the panic.

This patch unlocks the semaphore if it times out.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add infrastructure in the PF driver to support macvlan in the VF driver.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement setup of unicast address list in the VF driver's set_rx_mode
netdev op.  Unicast addresses are sent to the PF via a mailbox message
and the PF will check if it has room in the RAR table and if so set the
filter for the VF.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

At this point iph->daddr equals what rt->rt_dst would hold.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass in the sk_buff so that we can fetch the necessary keys from
the packet header when working with input routes.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow ip_options_build() to reliably look at the values of
iph->{daddr,saddr}
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code block executes when opt->srr_is_hit is set.  It will be
set only by ip_options_rcv_srr().

ip_options_rcv_srr() walks until it hits a matching nexthop in the SRR
option addresses, and when it matches one 1) looks up the route for
that nexthop and 2) on route lookup success it writes that nexthop
value into iph->daddr.

ip_forward_options() runs later, and again walks the SRR option
addresses looking for the option matching the destination of the route
stored in skb_rtable().  This route will be the same exact one looked
up for the nexthop by ip_options_rcv_srr().

Therefore "rt->rt_dst == iph->daddr" must be true.

All it really needs to do is record the route's source address in the
matching SRR option adddress.  It need not write iph->daddr again,
since that has already been done by ip_options_rcv_srr() as detailed
above.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

->read_proc interface is going away, switch to seq_file.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 1c5cae81 (net: call dev_alloc_name from register_netdevice),
a bug of bonding was involved, see example 1 and 2.

In register_netdevice(), the name of net_device is not valid until
dev_get_valid_name() is called. But dev->netdev_ops->ndo_init(that is
bond_init) is called before dev_get_valid_name(),
and it uses the invalid name of net_device.

I think register_netdevice() should make sure that the name of net_device is
valid before calling ndo_init().

example 1:
modprobe bonding
ls  /proc/net/bonding/bond%d

ps -eLf
root      3398     2  3398  0    1 21:34 ?        00:00:00 [bond%d]

example 2:
modprobe bonding max_bonds=3

[  170.100292] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[  170.101090] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
[  170.102469] ------------[ cut here ]------------
[  170.103150] WARNING: at /home/pwp/net-next-2.6/fs/proc/generic.c:586 proc_register+0x126/0x157()
[  170.104075] Hardware name: VirtualBox
[  170.105065] proc_dir_entry 'bonding/bond%d' already registered
[  170.105613] Modules linked in: bonding(+) sunrpc ipv6 uinput microcode ppdev parport_pc parport joydev e1000 pcspkr i2c_piix4 i2c_core [last unloaded: bonding]
[  170.108397] Pid: 3457, comm: modprobe Not tainted 2.6.39-rc2+ #14
[  170.108935] Call Trace:
[  170.109382]  [<c0438f3b>] warn_slowpath_common+0x6a/0x7f
[  170.109911]  [<c051a42a>] ? proc_register+0x126/0x157
[  170.110329]  [<c0438fc3>] warn_slowpath_fmt+0x2b/0x2f
[  170.110846]  [<c051a42a>] proc_register+0x126/0x157
[  170.111870]  [<c051a4dd>] proc_create_data+0x82/0x98
[  170.112335]  [<f94e6af6>] bond_create_proc_entry+0x3f/0x73 [bonding]
[  170.112905]  [<f94dd806>] bond_init+0x77/0xa5 [bonding]
[  170.113319]  [<c0721ac6>] register_netdevice+0x8c/0x1d3
[  170.113848]  [<f94e0e30>] bond_create+0x6c/0x90 [bonding]
[  170.114322]  [<f94f4763>] bonding_init+0x763/0x7b1 [bonding]
[  170.114879]  [<c0401240>] do_one_initcall+0x76/0x122
[  170.115317]  [<f94f4000>] ? 0xf94f3fff
[  170.115799]  [<c0463f1e>] sys_init_module+0x1286/0x140d
[  170.116879]  [<c07c6d9f>] sysenter_do_call+0x12/0x28
[  170.117404] ---[ end trace 64e4fac3ae5fff1a ]---
[  170.117924] bond%d: Warning: failed to register to debugfs
[  170.128728] ------------[ cut here ]------------
[  170.129360] WARNING: at /home/pwp/net-next-2.6/fs/proc/generic.c:586 proc_register+0x126/0x157()
[  170.130323] Hardware name: VirtualBox
[  170.130797] proc_dir_entry 'bonding/bond%d' already registered
[  170.131315] Modules linked in: bonding(+) sunrpc ipv6 uinput microcode ppdev parport_pc parport joydev e1000 pcspkr i2c_piix4 i2c_core [last unloaded: bonding]
[  170.133731] Pid: 3457, comm: modprobe Tainted: G        W   2.6.39-rc2+ #14
[  170.134308] Call Trace:
[  170.134743]  [<c0438f3b>] warn_slowpath_common+0x6a/0x7f
[  170.135305]  [<c051a42a>] ? proc_register+0x126/0x157
[  170.135820]  [<c0438fc3>] warn_slowpath_fmt+0x2b/0x2f
[  170.137168]  [<c051a42a>] proc_register+0x126/0x157
[  170.137700]  [<c051a4dd>] proc_create_data+0x82/0x98
[  170.138174]  [<f94e6af6>] bond_create_proc_entry+0x3f/0x73 [bonding]
[  170.138745]  [<f94dd806>] bond_init+0x77/0xa5 [bonding]
[  170.139278]  [<c0721ac6>] register_netdevice+0x8c/0x1d3
[  170.139828]  [<f94e0e30>] bond_create+0x6c/0x90 [bonding]
[  170.140361]  [<f94f4763>] bonding_init+0x763/0x7b1 [bonding]
[  170.140927]  [<c0401240>] do_one_initcall+0x76/0x122
[  170.141494]  [<f94f4000>] ? 0xf94f3fff
[  170.141975]  [<c0463f1e>] sys_init_module+0x1286/0x140d
[  170.142463]  [<c07c6d9f>] sysenter_do_call+0x12/0x28
[  170.142974] ---[ end trace 64e4fac3ae5fff1b ]---
[  170.144949] bond%d: Warning: failed to register to debugfs
Signed-off-by: NWeiping Pan <panweiping3@gmail.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug in the set_pauseparam
function that didn't well manage the ANE
field and returned broken values when use
ethtool -A|-a.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver used to call phy's ethtool configuration routine to start
auto-negotiation. This change has it call directly phy's routine to
start auto-negotiation.

The initial version was hiding phy_start_aneg() return value,
this patch returns it (<0 upon error).

Tested: module compiles, tested on STM HDK7108 STB.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The file st5481_init.c locally defines and initializes the adapter_list
variable, but does not use it for anything.  Removing the list makes it
possible to remove the list field from the st5481_adapter data structure.
In the function probe_st5481, it also makes it possible to free the locally
allocated adapter value on an error exit.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds IPPROTO_ICMP socket kind.  It makes it possible to send
ICMP_ECHO messages and receive the corresponding ICMP_ECHOREPLY messages
without any special privileges.  In other words, the patch makes it
possible to implement setuid-less and CAP_NET_RAW-less /bin/ping.  In
order not to increase the kernel's attack surface, the new functionality
is disabled by default, but is enabled at bootup by supporting Linux
distributions, optionally with restriction to a group or a group range
(see below).

Similar functionality is implemented in Mac OS X:
http://www.manpagez.com/man/4/icmp/

A new ping socket is created with

    socket(PF_INET, SOCK_DGRAM, PROT_ICMP)

Message identifiers (octets 4-5 of ICMP header) are interpreted as local
ports. Addresses are stored in struct sockaddr_in. No port numbers are
reserved for privileged processes, port 0 is reserved for API ("let the
kernel pick a free number"). There is no notion of remote ports, remote
port numbers provided by the user (e.g. in connect()) are ignored.

Data sent and received include ICMP headers. This is deliberate to:
1) Avoid the need to transport headers values like sequence numbers by
other means.
2) Make it easier to port existing programs using raw sockets.

ICMP headers given to send() are checked and sanitized. The type must be
ICMP_ECHO and the code must be zero (future extensions might relax this,
see below). The id is set to the number (local port) of the socket, the
checksum is always recomputed.

ICMP reply packets received from the network are demultiplexed according
to their id's, and are returned by recv() without any modifications.
IP header information and ICMP errors of those packets may be obtained
via ancillary data (IP_RECVTTL, IP_RETOPTS, and IP_RECVERR). ICMP source
quenches and redirects are reported as fake errors via the error queue
(IP_RECVERR); the next hop address for redirects is saved to ee_info (in
network order).

socket(2) is restricted to the group range specified in
"/proc/sys/net/ipv4/ping_group_range".  It is "1 0" by default, meaning
that nobody (not even root) may create ping sockets.  Setting it to "100
100" would grant permissions to the single group (to either make
/sbin/ping g+s and owned by this group or to grant permissions to the
"netadmins" group), "0 4294967295" would enable it for the world, "100
4294967295" would enable it for the users, but not daemons.

The existing code might be (in the unlikely case anyone needs it)
extended rather easily to handle other similar pairs of ICMP messages
(Timestamp/Reply, Information Request/Reply, Address Mask Request/Reply
etc.).

Userspace ping util & patch for it:
http://openwall.info/wiki/people/segoon/ping

For Openwall GNU/*/Linux it was the last step on the road to the
setuid-less distro.  A revision of this patch (for RHEL5/OpenVZ kernels)
is in use in Owl-current, such as in the 2011/03/12 LiveCD ISOs:
http://mirrors.kernel.org/openwall/Owl/current/iso/

Initially this functionality was written by Pavel Kankovsky for
Linux 2.4.32, but unfortunately it was never made public.

All ping options (-b, -p, -Q, -R, -s, -t, -T, -M, -I), are tested with
the patch.

PATCH v3:
    - switched to flowi4.
    - minor changes to be consistent with raw sockets code.

PATCH v2:
    - changed ping_debug() to pr_debug().
    - removed CONFIG_IP_PING.
    - removed ping_seq_fops.owner field (unused for procfs).
    - switched to proc_net_fops_create().
    - switched to %pK in seq_printf().

PATCH v1:
    - fixed checksumming bug.
    - CAP_NET_RAW may not create icmp sockets anymore.

RFC v2:
    - minor cleanups.
    - introduced sysctl'able group range to restrict socket(2).
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adapt new API.
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates compile warnings. The affected
variables are removed.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates a compile warning. The affected
variable is removed.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates compile warnings. The affected
variables are removed.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

-Wunused-but-set-variable generates a compile warning for lcs' tasklet
function. Invoked functions contain already error handling; thus
additional return code checking is not needed here.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused return code handling. The claw driver is mostly dead, so
just make sure it keeps compiling without warnings.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fill in the owner of qeth's ccw device driver.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch improves FFDC (first failure data capture) by requesting
a hardware trace in case the device driver, the hardware or a user
detects an error.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set rx csum default to hw checksumming again.
Remove sysfs interface for rx csum (checksumming) and TSO (large_send).
With the new hw_features it does not work to keep the old sysfs
interface in parallel. Convert options.checksum_type to new hw_features.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update driver version number
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver checks if the previous dump has been cleared before taking the dump.
It doesn't take the dump if it is not cleared.

Changes from v2:
Added lock to protect dump data structures from being mangled while
dumping or setting them via ethtool.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added code to take FW dump.
o Driver queries FW at the init time and gets the dump template
o It takes FW dump as per the dump template
o Level of FW dump (and its size) is configured via dump flag
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sending mbox cmds require multiple steps of writing to the DB register and polling
for an ack. Gettting interrupted in the middle by a signal breaks the mbox protocol.
Use msleep() to not get interrupted.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If waiting on POST returns prematurely (due to a signal), abort polling and return an error.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added code to take FW dump via ethtool. Dump level can be controlled via setting the
dump flag. A get function is provided to query the current setting of the dump flag.
Dump data is obtained from the driver via a separate get function.

Changes from v3:
Fixed buffer length issue in ethtool_get_dump_data function.
Updated kernel doc for ethtool_dump struct and get_dump_flag function.

Changes from v2:
Provided separate commands for get flag and data.
Check for minimum of the two buffer length obtained via ethtool and driver and
use that for dump buffer
Pass up the driver return error codes up to the caller.
Added kernel doc comments.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Save a bit of space.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I swear none of my compilers warned about this, yet it is so
obvious.

> net/ipv4/ip_forward.c: In function 'ip_forward':
> net/ipv4/ip_forward.c:87: warning: 'iph' may be used uninitialized in this function
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No matter what kind of header mangling occurs due to IP options
processing, rt->rt_dst will always equal iph->daddr in the packet.

So we can safely use iph->daddr instead of rt->rt_dst here.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already copy the 4-byte nexthop from the options block into
local variable "nexthop" for the route lookup.

Re-use that variable instead of memcpy()'ing again when assigning
to iph->daddr after the route lookup succeeds.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All call sites conditionalize the call to ip_options_rcv_srr()
with a check of opt->srr, so no need to check it again there.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should also fix updating of vlan_features and propagating changes to
VLAN devices on the bond.

Side effect: it allows user to force-disable some offloads on the bond
interface.

Note: NETIF_F_VLAN_CHALLENGED is managed by bond_fix_features() now.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It will be needed by bonding and other drivers changing vlan_features
after ndo_init callback.

As a bonus, this includes kernel-doc for netdev_update_features().
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes:
- while making NTB, driver shall check if device dwNtbOutMaxSize is higher than
 host value and shall add a short packet if this is the case
- previous temporary patch for this issue is replaced by this one
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove all remaining references to rt->rt_{src,dst}
by using dest->dst_saddr to cache saddr (used for TUN mode).
For ICMP in FORWARD hook just restrict the rt_mode for NAT
to disable LOCALNODE. All other modes do not allow
IP_VS_RT_MODE_RDR, so we should be safe with the ICMP
forwarding. Using cp->daddr as replacement for rt_dst
is safe for all modes except BYPASS, even when cp->dest is
NULL because it is cp->daddr that is used to assign cp->dest
for sync-ed connections.
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>