We disable the RPS interrupts for all platforms at the same spot, so
move it one level up in the callstack to simplify things.

No functional change.

v2:
- rebase on the GEN9 patches where RPS isn't supported yet, so we don't
  need to disable RPS interrupts on it (Paulo)
v3:
- avoid disabling the interrupts on GEN>9 too (Paulo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In sandybridge_pcode_read and sandybridge_pcode_write,
extend the mbox parameter from u8 to u32.

On Haswell and Sandybridge, bits 7:0 encode the mailbox
command and bits 28:8 are used for address control for
specific commands.

Based on suggestion from Ville Syrjälä.
Signed-off-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to "Cherryview_GFXclocks_y14w36d1.xlsx" the GPU frequency
divider should be 10 in when the CZ clock is 400 MHz. Change the code
to agree so that we report the correct frequencies.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The divider used in the GPU frequency calculations is compatible between
vlv and chv. vlv just wants doubled values compared to chv.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Always print the final PCBR register value on both vlv and chv, and
also tell us whether the BIOS was a good citizen or not.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Our freq<->opcode conversions assume that GPLL is always used.
Apparently that should be the case always, but let's scream if we
ever encounter something different.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Even with the rps debug messages signficantly recuced  by
 commit 67956867
 Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
 Date:   Tue Sep 2 15:12:17 2014 +0300

    drm/i915: Don't spam dmesg with rps messages on vlv/chv

we still get an inordinate amount of spam from this. Just kill the debug
print. If someone wants to observe it they can just use the tracepoint.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Given the history, there's some chance we'll keep the same WM code for a
bit (previously, we were able to reuse the same WM code from ILK to BDW,
so that sounds like a fair assumption).
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:

  Also according to Bspec the mailbox data1 register already existed
  since snb.  The hsw cdclk change sequence also mentions that it should
  be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
  in theory some pcode command might cause it to be clobbered, so I'm
  thinking we should just explicitly set it to 0 for all platforms in
  the pcode read/write functions
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When reading a CCK register we should obviously read it from CCK not
Punit. This problem has been present ever since this of code was
introduced in

 commit 67c3bf6f
 Author: Deepak S <deepak.s@linux.intel.com>
 Date:   Thu Jul 10 13:16:24 2014 +0530

    drm/i915: populate mem_freq/cz_clock for chv

The problem was raised during review by Mika [1] but somehow slipped
through the cracks, and the patch got applied with the problem unfixed.

[1] http://lists.freedesktop.org/archives/intel-gfx/2014-July/048937.html

Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The logical place for these functions is in i915_irq.c next to the rest of
PM interrupt handling functions.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The GEN6 and GEN8 versions differ only in the PM IIR and IER register
addresses and that on GEN8 we need to keep the
GEN8_PMINTR_REDIRECT_TO_NON_DISP PM interrupt unmasked. Abstract away
these 3 things in the GEN6 versions of the helpers and use them
everywhere.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The helpers to enable/disable PM IRQs for GEN6 and GEN8 are the same
except for the PM interrupt mask register, so abstract away this
register in the GEN6 versions and use these everywhere.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

-WaDisableDopClockGating:chv
-WaDisableSamplerPowerBypass:chv
-WaDisableGunitClockGating:chv
-WaDisableFfDopClockGating:chv
-WaDisableDopClockGating:chv

v2: Remove pre-production WA instead of restricting them
based on revision id (Ville)

For: VIZ-4090
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Configure and enable RC6 for Gen9.

v2: Rebase on top of BDW rc6 support (Damien)
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NZhe Wang <zhe1.wang@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we write new values for the DDB allocation and WM parameters, we now
need to trigger the double buffer update for the pipe to take the new
configuration into account.

As the DDB is a global resource shared between planes, enabling or
disabling one plane will result in changes for all planes that are
currently in use, thus the need write PLANE_SURF/CUR_BASE for more than
the plane we're touching.

v2: Don't wait for pipes that are off

v3: Split the staging results structure to not exceed the 1Kb stack
    allocation in skl_update_wm()

v4: Rework and document the algorithm after Ville found that it was all
    wrong.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To correctly flush the new DDB allocation we need to know about the pipe
allocation layout inside the DDB in order to sequence the re-allocation
to not cause a newly allocated pipe to fetch from a space that was
previously allocated to another pipe.

This patch preserves the per-pipe (start,end) allocation to be used in
the flush.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can reduce the indentation level by continuing early.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The transition WMs code was doing a shortcut and the values were copied
from the WM0 ones at compute_wm_results() time. Going forward, we want
to compute them like the other WMs and resolve their final register
values in the same way as well.

This patch does just that and isolate the transtion WM compute code in
skl_compute_transition_wm() while skl_compute_wm_results() takes care of
the register values.

We also take the opportunity to disable the transition WMs for now.
We've noticed underruns and they seem to be the culprit.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The DDB allocation code managed to split in two the compute functions.

Bring back skl_compute_transition_wm() and skl_compute_linetime_wm()
with their little friends.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To align with the ilk WM code and because it makes sense to test against
the upper bounds as soon as possible on variables that are bigger than
the number of bits in the register, let's move the maximum checks from
skl_compute_wm_results() to skl_compute_plane_wm().

v2: Leave the result values to 0 when overflowing the limits (Ville)
    Use 32 bits intermediate variables (Damien)

Instead of using the 16 and 8 bits space we have in the result
structure, use 32 bits local variables until we're sure they fit into
the constraints.
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

What we're talking about here is the DDB allocation (in blocks). That's
more descriptive than 'max_page_buff_alloc'.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ville suggested that we should use the same semantics as C arrays to
reduce the number of those pesky +1/-1 in the allocation code.

This patch leaves the debugfs file as is, showing the internal DDB
allocation structure, not the values written in the registers.

v2: Remove the test on ->end in skl_ddb_entry_size() (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Don't check DDB on pre-SKL platforms
    Don't check DDB state on disabled pipes

v3: Squash "Expose skl_ddb_get_hw_state()"
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This logically belongs to the WM state, so do it there.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We're going to add a new step, let's not hide the copy of the new WM
state inside one inner function, but as a 1st level operation in the WM
update.

v2: Split the staging results structure to not exceed the 1Kb stack
    allocation in skl_update_wm()
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to updated BSpec, If level 1 or any higher level has a value of 0x00,
that level and any higher levels are unused and the associated watermark
registers must not be enabled.

This patch checks for latency 0 for level >=1 and does not enable WM
corresponding to level m | m>=n, if level n (n != 0) has a 0us latency.

v2: Satheesh's review comments
	- zero-out latency values (for all higher levels if latency of given
	level is zero ) in read_wm_latency() function itself

v3: removed redundant check as per Satheesh's observation.
v4: rebase on top before merging (Damien)
v5: Rebase on top of the default value removal (Ville)

Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to the updated Bspec, The mailbox response data is not currently
accounting for memory read latency. Add 2 microseconds to the result for
each level.
This patch adds 2us to latency of level 0 for all cases and
for all other levels (1-7) only if latency[level] > 0.

v2: Slightly rework the patch and add a big comment (Damien)
v3: Rebase on top of the renames of the memory latency defines

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v1)
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: M, Satheeshakrishna <satheeshakrishna.m@intel.com> (v1)
Cc: Lespiau, Damien <damien.lespiau@intel.com>
Cc: M, Satheeshakrishna <satheeshakrishna.m@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch provides the implementation for reading the pipe wm HW
state.

v2: Incorporated Damien's review comments and also made modifications
    to incorporate the plane/cursor split.

v3: No need to ident a line that was fitting 80 chars
    Return early instead of indenting the remaining of a function
    (Damien)

v4: Rebase on top of nightly (minor conflict in intel_drv.h)
v5: Rebase on top of nightly (minor conflict in intel_drv.h)
v6: Rebase on top of nightly (minor conflict in intel_drv.h)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NPradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Adapt to the planes/cursor split
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Fix the 3rd plane/cursor logic (Pradeep Bhat)
v3: Fix one-by-one error in the DDB allocation code
v4: Rebase on top of the skl_pipe_pixel_rate() argument change
v5: Replace the available/start/end output parameters of
    skl_ddb_get_pipe_allocation_limits() by a single ddb entry constify
    a few arguments
    Make nth_active_pipe 0 indexed
    Use sizeof(variable) instead of sizeof(type)
    (Ville)
v6: Use the for_each_crtc() macro instead of list_for_each_entry()
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch implements the watermark algorithm and its necessary
functions. Two function pointers skl_update_wm and
skl_update_sprite_wm are provided. The skl_update_wm will update
the watermarks for the crtc provided as an argument and then
checks for change in DDB allocation for other active pipes and
recomputes the watermarks for those Pipes and planes as well.
Finally it does the register programming for all dirty pipes.
The trigger of the Watermark double buffer registers will have
to be once the plane configurations are done by the caller.

v2: fixed the divide-by-0 error in the results computation func.
    Also reworked the PLANE_WM register values computation func to
    make it more compact. Incorporated all other review comments
    from Damien.

v3: Changed the skl_compute_plane_wm function to now return success
    or failure. Also the result blocks and lines are computed here
    instead of in skl_compute_wm_results function.

v4: Adjust skl_ddb_alloc_changed() to the new planes/cursor split
    (Damien)

v5: Reworked the affected functions to implement new plane/cursor
    split.

v6: Rework the logic that triggers the DDB allocation and WM computation
    of skl_update_other_pipe_wm() to not depend on non-computed DDB
    values.
    Always give a valid cursor_width (at boot it's 0) to keep the
    invariant that we consider the cursor plane always enabled.
    Otherwise we end up dividing by 0 in skl_compute_plane_wm()
    (Damien Lespiau)

v7: Spell out allocation
    skl_ddb_ functions should have the ddb as first argument
    Make the skl_ddb_alloc_changed() parameters const
    (Damien)

v8: Rebase on top of the crtc->primary changes

v9: Split the staging results structure to not exceed the 1Kb stack
    allocation in skl_update_wm()

v10: Make skl_pipe_pixel_rate() take a pointer to the pipe config
     Add a comment about overflow considerations for skl_wm_method1()
     Various additions of const
     Various use of sizeof(variable) instead of sizeof(type)
     Various move of variable definitons to a narrower scope
     Zero initialize some stack allocated structures to make sure we
     don't have garbage in case we don't write all the values
     (Ville)

v11: Remove non-necessary default number of blocks/lines when the plane
     is disabled (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NPradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch defines the structures needed for computation of
watermarks of pipes and planes for SKL.

v2: Incorporated Damien's review comments and removed unused fields
    in structs for future features like rotation, drrs and scaling.
    The skl_wm_values struct is now made more generic across planes
    and cursor planes for all pipes.

v3: implemented the plane/cursor split.

v4: Change the wm union back to a structure (Ville, Daniel)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NPradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch reads the memory latency values for all the 8 levels for
SKL. These values are needed for the Watermark computation.

v2: Incorporated the review comments from Damien on register
    indentation.

v3: Updated the code to use the sandybridge_pcode_read for reading
    memory latencies for GEN9.

v4: Don't put gen 9 in the middle of an ordered list of ifs
    (Damien)

v5: take the rps.hw_lock around sandybridge_pcode_read() (Damien)

v6: Use gen >= 9 in the pcode_read() function for data1.
    Move the defines near the gen6 ones and prefix them with PCODE.
    Remove unused timeout define (the pcode_read() code has a larger
    timeout already).
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NPradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Current chv spec teels we can only use either 16 or 32 bits as precision.

Although in the past VLV went from 16/32 to 32/64 and spec might not be updated,
these precision values brings stability and fixes some issues Wayne was facing.

Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: NWayne Boyer <wayne.boyer@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Sprinkle const as requested by Ville.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's clean this a bit

v2: Rebase after other Mika's patch that removed some BDW production workarounds.
v3: Removed stepping info.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>