This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Structs called at91_nand_data where renamed to atmel_nand_data
and configs called *MTD_NAND_AT91* where renamed to
*MTD_NAND_ATMEL*. This was unfortunately not done consistently,
causing NAND chips not being initialised on several ARM boards.

I am aware that the author of the original change did not rename
MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example.
All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order
to keep naming consistency.

This patch was only tested on a MACH_SAM9_L9260, as this is the
only ARM board I have to my disposal.

Before this patch:

$ git-ls-files |xargs grep atmel_nand |wc -l
105
$ git-ls-files |xargs grep at91_nand |wc -l
4
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
8
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
47

After this patch:

$ git-ls-files |xargs grep atmel_nand |wc -l
109
$ git-ls-files |xargs grep at91_nand |wc -l
0
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
55
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
0
Signed-off-by: NPieter du Preez <pdupreez@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.

New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf).
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: NHåvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

typo in mci configuration in devices files
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

All the SAM9 boards supported by mainline and the AT91 patches have
been converted to the new-style UART initialization.  Therefore drop
support for the old at91_init_serial() interface for SAM9.

at91_uarts[] array can also be marked as __initdata.

The warning that no serial-console is defined moved from
at91_set_serial_console() to at91_add_device_serial() since the whole
point is the board-specific file is not calling
at91_set_serial_console().
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Register platform_devices for the Timer/Counter Block peripherals
found on the AT91RM9200, SAM9 & CAP9 processors.

Original patch from David Brownell.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On AT91 processors that include an ECC controller, pass its base
address to the NAND driver via platform_device resources.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91CAP9 processor includes the same Static Memory Controller
(SMC) peripheral as the SAM9 processors, but replaces the SDRAM
Controller with a DDR/SDR Controller (DDRSDRC).

This patch splits the existing
include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and
at91sam9_smc.h.
It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the LED initialization code out of the various *_devices.c files,
and into leds.c.
Also add support for NEW_LEDs.

Patch from David Brownell.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.

The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.

As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Map the complete memory region (SZ_256M) as is done on the other AT91
processors.

The SMC_SMARTMEDIA bit should be set in the EBI controller to enable
the hardware NAND logic.
  (Patch from Sascha Erlacher)
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Core support of the Atmel SSC library for all Atmel AT91 processors.

Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Replace hard-coded DMA mask (0xffffffff) with DMA_BIT_MASK(32) as
defined in dma-mapping.h.
Set "dma_mask" field for the UART platform_devices.
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add platform_device and initialization for the RTT (Real Time Timer)
and WDT (Watchdog) integrated in the Atmel AT91SAM9 processors.

For SAM9263, register both RTT peripherals.
   [From: David Brownell <dbrownell@users.sourceforge.net>]

Provide platform_resources for RTT peripherals
  [From: David Brownell <dbrownell@users.sourceforge.net>]

Add support for RTC peripheral on AT91SAM9RL (same RTC peripherals as
AT91RM9200)
  [From: David Brownell <dbrownell@users.sourceforge.net>]
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the Image Sensor Interface (ISI) peripheral integrated
in the Atmel AT91SAM9263 processor.

Patch from MaLiK
Signed-off-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91 I2C driver is currently marked as "broken" due to hardware
issues.  This patch enables AT91-based platforms to also use the
bitbanged GPIO for I2C.

This updates platform setup logic (setting up an i2c-gpio device
using the same pins as the i2c-at91 device, unless only the BROKEN
driver is enabled).

Also make use of the new-style initialization of I2C devices using
i2c_register_board_info().
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

- Include atmel_lcdc.h in at91sam926{1,3}_devices.c
Signed-off-by: NJan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Define SZ_512, SZ_256 and SZ_16 in asm-arm/sizes.h.
Remove the definitions from the at91*_devices.c files.

(Dependent on ARM patch #4370/2)
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The duplicate file "include/asm-arm/arch-at91rm9200/entry-macro.S" can
be removed - it was already moved to include/asm-arm/arch-at91/.

Fix 3 small typo's - two in comments, and the incorrect clock was
specified for the LCD device.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add support for the Atmel AT91SAM9263 processor.  It is similar to the
AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc.

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.

These changes are:
      * The system peripheral I/O region we remap has increased from
        0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
      * The increased I/O region forces changes to entry-macro.S and
        debug-macro.S due to ARM's limited immediate offset addressing
        modes.
      * Maximum number of GPIO banks increases to 5.
      * 2 MMC controllers so the board-setup code needs to specify which
        controller it wishes to use when calling at91_add_device_mmc().

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix build failure of AT91SAM9260.

The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a
"struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263)
ethernet driver (macb.c) [developed on the AVR32 architecture] expects a
"struct eth_platform_data".

Since the platform data of the two drivers is very similar, we continue
to use the "struct at91_eth_data" for all AT91 processors but add a
    #define eth_platform_data      at91_eth_data
in board.h to keep the MACB driver happy.

Original patch by Jan Altenberg.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add missing include for NAND device support on AT91SAM9260.
Signed-off-by: NWojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch includes the pin initialization, resource definition and
registration of the platform_devices for the SAM9260 and SAM9261
processors.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>