Bring in upstream updates for patches which depend on them

Pull scheduler fix from Thomas Gleixner:
 "Fix a long standing state race in finish_task_switch()"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Fix TASK_DEAD race in finish_task_switch()

Pull perf fix from Thomas Glexiner:
 "Fix build breakage on powerpc in perf tools"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Fix build break on powerpc due to sample_reg_masks

Pull maintainer email update from Thomas Gleixner:
 "Change Matt Fleming's email address in the maintainers file"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Change Matt Fleming's email address

Pull irq fixes from Thomas Gleixner:
 "Three trivial commits:

   - Fix a kerneldoc regression

   - Export handle_bad_irq to unbreak a driver in next

   - Add an accessor for the of_node field so refactoring in next does
     not depend on merge ordering"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdomain: Add an accessor for the of_node field
  genirq: Fix handle_bad_irq kerneldoc comment
  genirq: Export handle_bad_irq

Pull SCSI fixes from James Bottomley:
 "This is a set of three bug fixes, two of which are regressions from
  recent updates (the 3ware one from 4.1 and the device handler fixes
  from 4.2)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  3w-9xxx: don't unmap bounce buffered commands
  scsi_dh: Use the correct module name when loading device handler
  libiscsi: Fix iscsi_check_transport_timeouts possible infinite loop

Pull md bugfix from Neil Brown:
 "One bug fix for raid1/raid10.

  Very careless bug earler in 4.3-rc, now fixed :-)"

* tag 'md/4.3-rc4-fix' of git://neil.brown.name/md:
  crash in md-raid1 and md-raid10 due to incorrect list manipulation

If an irq chip does not implement the irq_disable callback, then we
use a lazy approach for disabling the interrupt. That means that the
interrupt is marked disabled, but the interrupt line is not
immediately masked in the interrupt chip. It only becomes masked if
the interrupt is raised while it's marked disabled. We use this to avoid
possibly expensive mask/unmask operations for common case operations.

Unfortunately there are devices which do not allow the interrupt to be
disabled easily at the device level. They are forced to use
disable_irq_nosync(). This can result in taking each interrupt twice.

Instead of enforcing the non lazy mode on all interrupts of a irq
chip, provide a settings flag, which can be set by the driver for that
particular interrupt line.
Reported-and-tested-by: NDuc Dang <dhdang@apm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1510092348370.6097@nanos

Merge tag 'gic-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core

GIC updates for Linux 4.4 from Marc Zyngier:

- Enable basic GICv3 support on 32bit ARM (mostly for running VMs with
  more than 8 virtual CPUs)
- arm64 changes to deal with firmware limitations that forces a GICv3
  to be used as a GICv2
- A GICv2m erratum workaround on Applied Micro X-Gene2

My Intel email address will soon expire. Replace it with my
personal address so people still know where to send patches.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1444494136-10333-1-git-send-email-matt@codeblueprint.co.ukSigned-off-by: NIngo Molnar <mingo@kernel.org>

Pull USB fixes from Greg KH:
 "Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.

  Nothing major here, full details in the shortlog, and all of these
  have been in linux-next for a while"

* tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: Add device quirk for Logitech PTZ cameras
  USB: chaoskey read offset bug
  USB: Add reset-resume quirk for two Plantronics usb headphones.
  usb: renesas_usbhs: Add support for R-Car H3
  usb: renesas_usbhs: fix build warning if 64-bit architecture
  usb: gadget: bdc: fix memory leak
  phy: berlin-sata: Fix module autoload for OF platform driver
  phy: rockchip-usb: power down phy when rockchip phy probe
  phy: qcom-ufs: fix build error when the component is built as a module

Pull tty/serial driver fixes from Greg KH:
 "Here are a few bug fixes for the tty core that resolve reported
  issues, and some serial driver fixes as well (including the
  much-reported imx driver problem)

  All of these have been in linux-next with no reported problems"

* tag 'tty-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  drivers/tty: require read access for controlling terminal
  serial: 8250: add uart_config entry for PORT_RT2880
  tty: fix data race on tty_buffer.commit
  tty: fix data race in tty_buffer_flush
  tty: fix data race in flush_to_ldisc
  tty: fix stall caused by missing memory barrier in drivers/tty/n_tty.c
  serial: atmel: fix error path of probe function
  tty: don't leak cdev in tty_cdev_add()
  Revert "serial: imx: remove unbalanced clk_prepare"

Pull staging fixes from Greg KH:
 "Here are two tiny staging tree fixes for 4.3-rc5.

  One fixes the broken speakup subsystem as reported by a user, and the
  other removes an entry in the MAINTAINERS file for a developer that
  doesn't want to be listed anymore"

* tag 'staging-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: speakup: fix speakup-r regression
  MAINTAINERS: Remove myself as nvec co-maintainer

Pull char/misc driver fixes from Greg KH:
 "Here are some small fixes for some misc drivers that resolve some
  reported issues.  All of these have been linux-next for a while"

* tag 'char-misc-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mcb: Fix error handling in mcb_pci_probe()
  mei: hbm: fix error in state check logic
  nvmem: sunxi: Check for memory allocation failure
  nvmem: core: Fix memory leak in nvmem_cell_write
  nvmem: core: Handle shift bits in-place if cell->nbits is non-zero
  nvmem: core: fix the out-of-range leak in read/write()

Pull MIPS fixes from Ralf Baechle:

 - MIPS didn't define the new ioremap_uc.  Defined it as an alias for
   ioremap_uncached.

 - Replace workaround for MIPS16 build issue with a correct one.

* git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Define ioremap_uc
  MIPS: UAPI: Ignore __arch_swab{16,32,64} when using MIPS16
  Revert "MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16."

Pull swiotlb fixlet from Konrad Rzeszutek Wilk:
 "Enable the SWIOTLB under 32-bit PAE kernels.

  Nowadays most distros enable this due to CONFIG_HYPERVISOR|XEN=y which
  select SWIOTLB.  But for those that are not interested in
  virtualization and wanting to use 32-bit PAE kernels and wanting to
  have working DMA operations - this configures it for them"

* 'stable/for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb: Enable it under x86 PAE

Leandro Awa writes:
 "After switching to version 4.1.6, our parallelized and distributed
  workflows now fail consistently with errors of the form:

  T34: ./regex.c:39:22: error: config.h: No such file or directory

  From our 'git bisect' testing, the following commit appears to be the
  possible cause of the behavior we've been seeing: commit 766c4cbf"

Al Viro says:
 "What happens is that 766c4cbf got the things subtly wrong.

  We used to treat d_is_negative() after lookup_fast() as "fall with
  ENOENT".  That was wrong - checking ->d_flags outside of ->d_seq
  protection is unreliable and failing with hard error on what should've
  fallen back to non-RCU pathname resolution is a bug.

  Unfortunately, we'd pulled the test too far up and ran afoul of
  another kind of staleness.  The dentry might have been absolutely
  stable from the RCU point of view (and we might be on UP, etc), but
  stale from the remote fs point of view.  If ->d_revalidate() returns
  "it's actually stale", dentry gets thrown away and the original code
  wouldn't even have looked at its ->d_flags.

  What we need is to check ->d_flags where 766c4cbf does (prior to
  ->d_seq validation) but only use the result in cases where we do not
  discard this dentry outright"
Reported-by: NLeandro Awa <lawa@nvidia.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=104911
Fixes: 766c4cbf ("namei: d_is_negative() should be checked...")
Tested-by: NLeandro Awa <lawa@nvidia.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: NTrond Myklebust <trond.myklebust@primarydata.com>
Acked-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull power management and ACPI fixes from Rafael Wysocki:
 "These are four fixes for bugs in the devfreq and cpufreq subsystems,
  including two regression fixes (one for a recent regression and one
  for a problem introduced in 4.2).

  Specifics:

   - Two fixes for cpufreq regressions, an acpi-cpufreq driver one
     introduced during the 4.2 cycle when we started to preserve cpufreq
     directories for offline CPUs and a general one introduced recently
     (Srinivas Pandruvada).

   - Two devfreq fixes, one for a double kfree() in an error code path
     and one for a confusing sysfs-related failure (Geliang Tang, Tobias
     Jakobi)"

* tag 'pm+acpi-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: prevent lockup on reading scaling_available_frequencies
  cpufreq: acpi_cpufreq: prevent crash on reading freqdomain_cpus
  PM / devfreq: fix double kfree
  PM / devfreq: Fix governor_store()

Pull strscpy powerpc fix from Chris Metcalf.

Fix powerpc big-endian build.

* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/powerpc: provide zero_bytemask() for big-endian

Pull sound fixes from Takashi Iwai:
 "We see various small fixes, but nothing looks too scary, all are small
  gentle bug fixes:

   - Most of changes are for ASoC codecs: Realtek, SGTL5000, TAS2552,
     TLV320, WM8962

   - A couple of dwc and imx-ssi fixes

   - Usual oneliner HD-audio quirks

   - An old emux synth code fix"

* tag 'sound-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  MAINTAINERS: Remove wm97xx entry
  ASoC: tas2552: fix dBscale-min declaration
  ALSA: synth: Fix conflicting OSS device registration on AWE32
  ALSA: hda - Disable power_save_node for IDT 92HD73xx chips
  ALSA: hda - Apply SPDIF pin ctl to MacBookPro 12,1
  ALSA: hda: Add dock support for ThinkPad T550
  ASoC: dwc: fix dma stop transferring issue
  ASoC: dwc: correct irq clear method
  ASoC: tlv320aic3x: Prevent writing reserved registers on tlv320aic3104 CODECs
  ASoC: rt5645: Correct the naming and setting of ADC Boost Volume Control
  ASoC: sgtl5000: fix wrong register MIC_BIAS_VOLTAGE setup on probe
  ASoC: wm8962: balance pm_runtime_enable
  ASoC: imx-ssi: Fix DAI hardware signal inversions
  ASoC: sgtl5000: fix error message output for MicBias voltage
  ASoC: db1200: Fix DAI link format for db1300 and db1550

Pull clk fixes from Stephen Boyd:
 "A Samsung driver fix and a handful of TI driver fixes"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: ti: dflt: fix enable_reg validity check
  clk: ti: fix dual-registration of uart4_ick
  clk: ti: clk-7xx: Remove hardwired ABE clock configuration
  clk: samsung: fix cpu clock's flags checking

Pull MMC fixes from Ulf Hansson:
 "MMC host:
   - omap_hsmmc: Fix boot regressions for omap4430
   - omap_hsmmc: Fix legacy boot regression for omap3
   - sdhci-pxav3: Fix some clock issues for Armada 38x
   - sdhci-pxav3: Fix error handling at probe
   - sdhci-of-at91: Fix clock stabilization problem"

* tag 'mmc-v4.3-rc4' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: sdhci-of-at91: use SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST quirk
  mmc: sdhci: add quirk SDHCI_QUIRK2_NEED_DELAY_AFTER_INT_CLK_RST
  mmc: sdhci-pxav3: fix error handling of armada_38x_quirks
  mmc: sdhci-pxav3: disable clock inversion for HS MMC cards
  mmc: sdhci-pxav3: remove broken clock base quirk for Armada 38x sdhci driver
  mmc: host: omap_hsmmc: Fix MMC for omap3 legacy booting
  Revert "mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias status"

Pull dm fixes from Mike Snitzer:
 "Three stable fixes:

   - DM core AB-BA deadlock fix in the device destruction path (vs
     device creation's DM table swap).

   - DM raid fix to properly round up the region_size to the next
     power-of-2.

   - DM cache fix for a NULL pointer seen while switching from the
     "cleaner" cache policy.

  Two fixes for regressions introduced during the 4.3 merge:

   - request-based DM error propagation regressed due to incorrect
     changes introduced when adding the bi_error field to bio.

   - DM snapshot fix to only support snapshots that overflow if the
     client (e.g. lvm2) is prepared to deal with the associated
     snapshot status interface change"

* tag 'dm-4.3-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm snapshot: add new persistent store option to support overflow
  dm cache: fix NULL pointer when switching from cleaner policy
  dm: fix request-based dm error reporting
  dm raid: fix round up of default region size
  dm: fix AB-BA deadlock in __dm_destroy()

Pull btrfs fixes from Chris Mason:
 "These are small and assorted.  Neil's is the oldest, I dropped the
  ball thinking he was going to send it in"

* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: support NFSv2 export
  Btrfs: open_ctree: Fix possible memory leak
  Btrfs: fix deadlock when finalizing block group creation
  Btrfs: update fix for read corruption of compressed and shared extents
  Btrfs: send, fix corner case for reference overwrite detection

Pull nfsd bugfix from Bruce Fields:
 "Just one RDMA bugfix"

* tag 'nfsd-4.3-1' of git://linux-nfs.org/~bfields/linux:
  svcrdma: handle rdma read with a non-zero initial page offset

Pull ARM SoC fixes from Arnd Bergmann:
 "The fixes for this week include one small patch that was years in the
  making and that finally fixes using all eight CPUs on exynos542x.

  The rest are lots of minor changes for sunxi, imx, exynos and shmobile

   - fixing the minimum voltage for Allwinner A20
   - thermal boot issue on SMDK5250.
   - invalid clock used for FIMD IOMMU.
   - audio on Renesas r8a7790/r8a7791
   - invalid clock used for FIMD IOMMU
   - LEDs on exynos5422-odroidxu3-common
   - usb pin control for imx-rex
   - imx53: fix PMIC interrupt level
   - a Makefile typo"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: Fix wrong clock binding for sysmmu_fimd1_1 on exynos5420
  ARM: dts: Fix bootup thermal issue on smdk5250
  ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain for sound
  ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain for sound
  arm-cci500: Don't enable PMU driver by default
  ARM: dts: fix usb pin control for imx-rex dts
  ARM: imx53: qsrb: fix PMIC interrupt level
  ARM: imx53: include IRQ dt-bindings header
  ARM: dts: add suspend opp to exynos4412
  ARM: dts: Fix LEDs on exynos5422-odroidxu3
  ARM: EXYNOS: reset Little cores when cpu is up
  ARM: dts: Fix Makefile target for sun4i-a10-itead-iteaduino-plus
  ARM: dts: sunxi: Raise minimum CPU voltage for sun7i-a20 to meet SoC specifications

Hardware virtualisation of GICv3 is only supported by 64bit hosts for
the moment. Some VGICv3 bits are missing from the 32bit side, and this
patch allows to still be able to build 32bit hosts when CONFIG_ARM_GIC_V3
is selected.

To this end, we introduce a new option, CONFIG_KVM_ARM_VGIC_V3, that is
only enabled on the 64bit side. The selection is done unconditionally
because CONFIG_ARM_GIC_V3 is always enabled on arm64.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This patch allows ARM guests to use GICv3 on an arm64 host
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Implement the system and memory-mapped register accesses in
asm/arch_gicv3.h for 32bit architectures.

This patch is a straightforward translation of the arm64 header. 64bit
accesses are done in two times and don't need atomicity: TYPER is
read-only, and the upper-word of IROUTER is always zero on 32bit
architectures.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

On 32bit platforms, we cannot assure that an I/O ldrd or strd will be
done atomically. Besides, an hypervisor would be unable to emulate such
accesses.
In order to allow the AArch32 version of the driver to split them into
two 32bit accesses while keeping the requirement for atomic writes, this
patch specializes the IROUTER and TYPER accesses.
Since the latter is an ID register, it won't need to be read atomically,
but we still avoid future confusion by using gic_read_typer instead of a
generic gic_readq.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This patch does a few simple compatibility-related changes:
- change the system register access prototypes to their actual size,
- homogenise mpidr accesses with unsigned long,
- force the 64bit register values to unsigned long long.

Note: the list registers are 64bit on GICv3, but the AArch32 vGIC driver
will need to split their values into two 32bit registers: LRn and LRCn.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This patch moves the GICv3 system register access helpers to
arch/arm64/. Their 32bit counterparts will need to use mrc/mcr accesses
instead of mrs_s/msr_s.

[maz: fixed conflict with Cavium erratum handling]
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

APM X-Gene GICv2m implementation has an erratum where the
MSI data needs to be the offset from the spi_start in order to
trigger the correct MSI interrupt. This is different from the
standard GICv2m implementation where the MSI data is the absolute
value within the range from spi_start to (spi_start + num_spis)
of each v2m frame.

This patch reads MSI_IIDR register (present in all GICv2m
implementations) to identify X-Gene GICv2m implementation and
apply workaround to change the data portion of MSI vector.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NDuc Dang <dhdang@apm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The current requirements do not describe the case where a GICv3
system gets booted with system register access disabled, and
expect the kernel to drive GICv3 in GICv2 mode.

Describe the expected settings for that particular case.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When using a GICv3 in compatibility (v2) mode, having GICv3 system
register access enabled is not really compliant with the architecture.

Warn if the firmware (or the hypervisor) has been lazy.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

As the firmware (or the hypervisor) may have disabled SRE access,
check that SRE can actually be enabled before declaring that we
do have that capability.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In order for gic_enable_sre to be used by the arm64 core code,
move it to arm-gic-v3.h. As a bonus, we now also check if
system registers have been already enabled, and return early
if they have.

In all cases, the function now returns a boolean indicating if
the enabling has been successful.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Contrary to what was originally expected, EL3 firmware can (for whatever
reason) disable GICv3 system register access. In this case, the kernel
explodes very early.

Work around this by testing if the SRE bit sticks or not. If it doesn't,
abort the GICv3 setup, and pray that the firmware has passed a DT that
doesn't contain a GICv3 node.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Commit 76c44f6d introduced the possibly for "Overflow" to be reported
by the snapshot device's status.  Older userspace (e.g. lvm2) does not
handle the "Overflow" status response.

Fix this incompatibility by requiring newer userspace code, that can
cope with "Overflow", request the persistent store with overflow support
by using "PO" (Persistent with Overflow) for the snapshot store type.
Reported-by: NZdenek Kabelac <zkabelac@redhat.com>
Fixes: 76c44f6d ("dm snapshot: don't invalidate on-disk image on snapshot write overflow")
Reviewed-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>