This Conexant codec has a single jack that can be used as either
headphone or mic (but not headset). The existing hp_mic functionality
does not apply here, because the mic and the HP are on separate pins.

Hence make a lighter version of what has been earlier done for Realtek
codecs.

BugLink: https://bugs.launchpad.net/bugs/1198030Tested-by: NFranz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

sound/pci/rme9652/hdspm.c:1110:2-3: Unneeded semicolon

Generated by: coccinelle/misc/semicolon.cocci
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Commit 8f898e92 removed the redundant
reads of bInterfaceProtocol from the descriptors, but introduced a
regression to devices with quirks of type QUIRK_AUDIO_FIXED_ENDPOINT,
since fp->protocol is not set in setup process.

As a consequence, audio streams would not get initialized, as the
following logs show:

[   48.923043] setting usb interface 3:1
[   48.923056] Creating new capture data endpoint #81
[   48.923484] 4:3:1: cannot set freq 48000 to ep 0x81

This patch sets fp->protocol in create_fixed_stream_quirk() and
resolves the regression.
Signed-off-by: NEldad Zack <eldad@fogrefinery.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

"pcm" member in struct fwspk is used to set pcm operations but is not used
again. This commit remove this member and set pcm operations with
snd_pcm_set_ops().
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ALC5505 DSP is enabled even though we don't use the features yet at
all.  This results in the unnecessarily high power consumption, more
than 100mV higher.  Until we implement the DSP support, better to
bypass DSP for saving more power.
Reported-by: NMengdong Lin <mengdong.lin@intel.com>
[Patch modified by Mengdong to cal alc5505_dsp_init() with extra
acl5505_dsp_halt().]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMartin Dausel <martin.dausel@iosono-sound.com>
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also use snd_ctl_enum_info() to fill the autosync text fields on AES32
and MADI cards (only users of snd_hdspm_info_autosync_ref).
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also use snd_ctl_enum_info() to fill the autosync enumerated controls.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use snd_ctl_enum_info() to fill most of the enumerated controls. More
non-trivial occurrences will follow in separate commits.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch finally enables TCO support on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a new ALSA control to read the external sample rate from
userspace on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch refactors the code to query the external sample rate and its
translation into the corresponding enum into a helper function to
prevent future code duplication.

A later commit will make use of this new helper function.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Also report TCO status and Sync-In via /proc/ on AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch enables the user to select "TCO" and "Sync In" as a preferred
sync reference on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds support to read the TCO sample rate in
hdspm_external_sample_rate() on RME AES(32) cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

As mentioned in the comment, the AES32 cards must not set the format
bit, since it is used to indicate the preferred sync setting instead.

We hence simply skip the corresponding part in the hw_params function.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds AES32 specific code to hdspm_get_tco_sample_rate to
query the TCO sample rate.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds AES32 specific code to hdspm_get_wc_sample_rate() to
query the wordclock frequency.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch only introduces prototype declarations, no real change. The
functions themselves are already present.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Helper function to return the AES sample rate class. This class needs to
be translated via HDSPM_bit2freq() to get the more common
representation.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Provide the text for the two new clock options "TCO" and "Sync In" on
AES32 cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HDSPM_AUTOSYNC_REF macro is only implemented for MADI and AES32
cards, so it doesn't make sense to call it on AIO boards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch does nothing, it's sole intent is to clean up the code.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

HDSPM_tco_lock and HDSPM_tcoLock were too close, so the previous code
didn't honour the difference between the two.

Let's be more verbose and use HDSPM_tcoLockMadi for MADI cards,
HDSPM_tcoLockAes for AES(32) and fix the code that makes use of both.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch separates the TCO bits from snd_hdspm_proc_read_madi(), so
the new function can later be shared between MADI and AES32 cards.

It's essentially only moving code around, no new functionality.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This is a left-over mistake from old code, the correct register offset is
provided in kcontrol->private_value, not in the index.
Cf. RayDAT case, where it has already been corrected.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AIO cards allow to use AEB (Analogue Expansion Boards) to add four
input and/or output channels.

This patch adds the necessary code to detect and enable the additional
I/O channels.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch uses the newly introduced HDSPM_CONTROL_TRISTATE functions to
create and expose the following ALSA controls:

   - Gain selection for Input, Output and Phones (HiGain, +4dBu, -10dbV)
   - S/PDIF Input select (Coaxial, Optical, Internal)
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

AIO cards offer at least four individual settings options with three
states each. Those settings are represented as two bits in the settings
register with the following meaning:

   0*some_base_bit --> Option value 0
   1*some_base_bit --> Option value 1
   2*some_base_bit --> Option value 2
   3*some_base_bit --> mask to select the two involved bits

This patch adds a generic ALSA control macro for such a value-to-bit
pattern mapping. It will be used in a later commit to expose four new
controls.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ENUMERATED_CTL_INFO is a macro, so the binary code is generated multiple
times. To avoid code duplication, refactor the involved functionality
into a function and make ENUMERATED_CTL_INFO a call to this function.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds the following ALSA controls:

   - S/PDIF Out Optical to switch S/PDIF Out from coaxial to optical
   - S/PDIF Out Professional to send the Pro bit in the output stream
   - ADAT-Internal to enable ADAT/TDIF Expansion Board (AEB/TEB)
   - XLR Breakout Cable if analogue I/O uses the XLR breakout cable
   - WCK48 to force WordClock to the 32-48kHz range (single speed) if
     the card is operating at higher frequencies
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This commit adds new ALSA controls to send single-speed WordClock and
S/PDIF-Professional on RME RayDAT cards.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

hdspm_set_system_clock_mode() is almost a one-by-one copy of
hdspm_set_toggle_setting(). To improve code quality, remove the
duplication.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HDSPM_TOGGLE_SETTING functions alter the control_register on older
cards. On newer cards (AIO/RayDAT), they have to operate on the
settings_register instead.

This patch augments the existing functions to work with AIO/RayDAT, too.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

RME RayDAT and AIO cards are new designs with different register
settings. Since we need to distinguish them from older cards multiple
times in the driver, refactor the code into a separate helper function.

No functional change intended.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The driver did not support all possible configurations. These defines
will be used by later commits to add the missing functionality.
Signed-off-by: NAdrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Finally all the static quirks in patch_analog.c are reduced by this
patch.  As machines with AD1986A codec are all old and often their
BIOS are buggy, we need to keep at least a few static pin conifgs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Most of ASUS laptops and Lenovo N100 provide proper BIOS pin-configs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The BIOS provides good pin-configurations, so we can drop the static
quirk now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BIOS on Samsung R55, M55 and M50 provide the proper pin-configs,
so we can remove the corresponding static quirk entries gracefully.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>