Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 21 8月, 2009 4 次提交
  3. 20 8月, 2009 16 次提交
  5. 19 8月, 2009 2 次提交
  7. 18 8月, 2009 6 次提交
  9. 16 8月, 2009 3 次提交
    • M
      sh: Add support for DWARF GNU extensions · cd7246f0
      由 Matt Fleming 提交于 
      Also, remove the "fix" to DW_CFA_def_cfa_register where we reset the
frame's cfa_offset to 0. This action is incorrect when handling
DW_CFA_def_cfa_register as the DWARF spec specifically states that the
previous contents of cfa_offset should be used with the new
register. The reason that I thought cfa_offset should be reset to 0 was
because it was being assigned a bogus value prior to executing the
DW_CFA_def_cfa_register op. It turns out that the bogus cfa_offset value
came from interpreting .cfi_escape pseudo-ops (those used by the GNU
extensions) as CFA_DW_def_cfa ops.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
      cd7246f0
    • M
      sh: Try again at getting the initial return address for an unwind · b955873b
      由 Matt Fleming 提交于 
      The previous hack for calculating the return address for the first frame
we unwind (dwarf_unwinder_dump) didn't always work. The problem was that
it assumed once it read the rule for calculating the return address,
there would be no new rules for calculating it. This isn't true because
the way in which the CFA is calculated can change as you progress
through a function and the return address is figured out using the
CFA. Therefore, the way to calculate the return address can change.

So, instead of using some offset from the beginning of
dwarf_unwind_stack which is just a flakey approach, and instead of
executing instructions from the FDE until the return address is setup,
we now figure out the pc in dwarf_unwind_stack() just before we call
dwarf_cfa_execute_insns().
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
      b955873b
    • P
      sh: Merge the _32/_64 variants of arch/sh/kernel/Makefile. · 38f9ddf4
      由 Paul Mundt 提交于 
      This uses the BITS export as per x86 in order to allow the same Makefile
to be used.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      38f9ddf4
  11. 15 8月, 2009 9 次提交
    • P
      Merge branch 'sh/stable-updates' · 60e0a4c7
      由 Paul Mundt 提交于
      60e0a4c7
    • M
      sh: sh7724 ddr self-refresh changes · 237674e0
      由 Magnus Damm 提交于 
      This patch updates the SuperH Mobile sleep assembly code with
support for DBSC memory controller found in the sh7724 processor.

Without this fix the memory hooked up to the sh7724 processor
will never enter self-refresh mode before suspending to ram. The
effect of this is that the memory contents most likeley will be
lost upon resume which may or may not be what you want.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      237674e0
    • M
      sh: use in-soc KEYSC on se7724 · 9747e78b
      由 Magnus Damm 提交于 
      This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.

Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.

Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      9747e78b
    • M
      sh: CMT suspend/resume · f6431732
      由 Magnus Damm 提交于 
      This patch updates the SuperH CMT driver with suspend and resume
callbacks for the suspend-to-ram case. This patch stops the CMT
channel at suspend time to avoid unwanted wake up events.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      f6431732
    • M
      sh: skip disabled LCDC channels · 21bc1f02
      由 Magnus Damm 提交于 
      This patch updates the SuperH Mobile LCDC driver to skip
over disabled channels. Without this patch suspend-to-ram
operation will crash if deferred io is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      21bc1f02
    • M
      sh: Set the cfa_offset to 0 if we see a DW_CFA_def_cfa_register op · 180aa6e6
      由 Matt Fleming 提交于 
      The way that the CFA is calculated can change as we progress through a
function. If we see a DW_CFA_def_cfa_register op we need to reset the
frame's cfa_offset value which may have been previously setup.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      180aa6e6
    • P
      sh: delay slot future proofing via EXPMASK on SH-4A parts. · 7dd6662a
      由 Paul Mundt 提交于 
      This implements EXPMASK initialization code for SH-4A parts, where it is
possible to disable compat features that will go away in newer cores.
Presently this includes disabling support for non-nop instructions in the
rte delay slot, as well as a sleep instruction being placed in a delay
slot (neither of which the kernel does any longer). As a result of this,
any future offenders will have illegal slot exceptions generated for
them.

Associative writes for the memory-mapped cache array are still left
enabled, until such a point that special cache operations for SH-4A are
provided to move off of the current (and rather dated) SH-4 versions.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      7dd6662a
    • P
      sh: Make sure rte delay slots are nopped out on all parts. · 7a90e00d
      由 Paul Mundt 提交于 
      Future SH parts do not support any instruction but a nop in the rte delay
slot, so make the change for all offending parts. SH-5 is excluded from
this, and already has its own set of restrictions with regards to rte
delay slot handling.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      7a90e00d
    • P
      sh: stacktrace: Properly terminate the trace entry buffer. · 606b4c99
      由 Paul Mundt 提交于 
      This inserts a ULONG_MAX entry at the end of the valid entries in the
stack trace buffer so the default code doesn't need to scan to the end of
available slots. This also makes the trace buffer termination behaviour
consistent with the other architectures.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
      606b4c99