Network devices need to be free'd with free_netdev() not kfree()
otherwise the kernel will panic if an application has /sys/class/net/ethX/value
open and reads it.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Complete removal of proc stuff from chelsio. The orignal driver had a debug
proc interface, but not all the code got removed.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Whitespace cleanups.  Replace leading spaces with tabs and fix indentation
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The chelsio network driver has some extra ifdef's that got in because the
driver was originally based on code that worked on 2.4 as well as 2.6.
This patch removes the dead code.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Include of_platform header, and use
new of_[un]register_platform_driver() fns.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use NULL instead of 0 for pointers (cures sparse warnings).

drivers/net/sundance.c:1106:16: warning: Using plain integer as NULL pointer
drivers/net/sundance.c:1652:16: warning: Using plain integer as NULL pointer
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: 1G/10G Ethernet Driver updates
	- Temparature monitoring and device control
	- Memory footprint reduction
	- Driver changes to support newer version of firmware
Signed-off-by: NAmit S. Kale <amitkale@netxen.com>

 netxen_nic.h          |  165 ++++++++++++++++++++++++++++++++--
 netxen_nic_ethtool.c  |   89 ++++++++++++------
 netxen_nic_hdr.h      |   71 +++++++++++++-
 netxen_nic_hw.c       |  206 +++++++++++++++++++++++++++++--------------
 netxen_nic_hw.h       |    8 +
 netxen_nic_init.c     |  239 +++++++++++++++++++++++++++++++++++++++++---------
 netxen_nic_ioctl.h    |   12 +-
 netxen_nic_isr.c      |   54 +++++------
 netxen_nic_main.c     |  121 +++++++++++++++++--------
 netxen_nic_niu.c      |  172 +++++++++++++++++++++++++++--------
 netxen_nic_phan_reg.h |   24 ++++-
 11 files changed, 891 insertions(+), 270 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAmit S. Kale <amitkale@netxen.com>

 netxen_nic_main.c |    3 ++-
 1 files changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When scanning in debug mode, softmac is very chatty in that it puts
3 lines in the logs for each time it scans. This patch has only one
line containing all the information previously reported.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bcm43xx and ipw2100 currently duplicate the same simplistic get_stats
handler.  Additionally, zd1211rw requires the same handler to fix a
bug where all stats are reported as 0.

This patch adds a generic implementation to the ieee80211 layer,
which drivers are free to override.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds zd1211rw driver support for the softmac functionality I
added a while back. We now obey changes in basic rates, use short
preamble if it is available (but long if the AP says it's not),
and send self-CTS in the proper situations.

Locking fixed and improved by Ulrich Kunitz.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These controlset rate constants are also applicable in places outside
the controlset, such as in the RTS/CTS control register.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Eric Goff found that he could not use his ZD1211 device which is
programmed for the Japan regulatory domain. It turns out that ZyDAS
deviate from the spec here: they do not use the newer Japan region code
(0x41) but their drivers do operate as if the newer Japan legal
frequency range is in effect.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a high number of split USB transactions, which contain
only one packet but have a length info field. This patch optimizes
this code by stopping parsing the length info structure if a zero
length field is encountered.
Signed-off-by: NUlrich Kunitz <kune@deine-taler.de>
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bit-field constants in zd_chip.h are now defined using a shift expression.
The value 0x08 is now (1 << 3). The fix is intended to improve readability.

Remove misleading comment in zd_mac.c: The function already returns -EPERM
in managed mode (IW_MODE_INFRA).

Remove unused code in zd_mac.c: The unused code intended for debugging
rx_status values is no longer useful.

Added dump_stack() to ZD_ASSERT macro: Output of the stack helps to debug
assertions. Keep in mind that the ZD_ASSERT() macro only results in code,
if DEBUG is defined.

Improved comments for filter_rx()

zd_usb.c: Added driver name to module init and exit functions
Signed-off-by: NUlrich Kunitz <kune@deine-taler.de>
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

http://bugzilla.kernel.org/show_bug.cgi?id=7399

zd1211rw's support for IW_FREQ_AUTO is broken: when specified, the driver
tries to change to a channel specified in an uninitialized integer. As
IW_FREQ_AUTO is hard to implement properly, the solution (at least for now)
is to drop support for it and start ignoring the flags like all other wireless
drivers do.

This has the added advantage that kismet also starts working with zd1211rw,
even though kismet requesting IW_FREQ_AUTO is also a bug (fixed in their svn)
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And use kmemdup and kzalloc where applicable
Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

zd1211b chip 050d:705c v4810 high 00-17-3f AL2230_RF pa0 g--N

Tested by Bryan Barnard
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

zd1211 chip 14ea:ab13 v4330 high 00-90-cc AL2230_RF pa0 g---

Tested by Tetsuya Yatagai.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Failure of pci_set_mwi should not be considered a fatal error.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the patch sent by Daniel Drake under the title "[PATCH] ieee80211: Move
IV/ICV stripping into ieee80211_rx", a needed line was accidentally removed.

(NOTE: I'm pretty sure this was my fault, not Daniel's. -- JWL)
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 477c517903d57047150b01608149e02c6e9d83dd.

This patch depended on something that was not yet committed.

Driver for the Atmel MACB on-chip ethernet module.

Tested on AVR32/AT32AP7000/ATSTK1000. I've heard rumours that it works
with AT91SAM9260 as well, and it may be possible to share some code with
the at91_ether driver for AT91RM9200.

Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682

Changes since previous version:
  * Probe for PHY ID instead of depending on it being provided through
    platform_data.
  * Grab initial ethernet address from the MACB registers instead
    of depending on platform_data.
  * Set MII/RMII mode correctly.

These changes are mostly about making the driver more compatible with
the at91 infrastructure.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Another thing, reported recently to me by several people - DSCC4 WAN
driver now (and perhaps for the last couple of years+) requires the
generic HDLC. I've fixed the Kconfig and moved the DSCC4 option
under CONFIG_HDLC so it's consistent visually.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add tsi108/9 on chip Ethernet controller driver support.

The driver code collects the feedback of previous posting form the mailing
list and gives the update.

MPC7448HPC2 platform in arch/powerpc uses tsi108 bridge.

The following is a brief description of the Ethernet controller:

The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1.  It uses a single Management interface to
manage the two physical connection devices (PHYs).  Each Ethernet port has
its own statistics monitor that tracks and reports key interface
statistics.  Each port supports a 256-entry hash table for address
filtering.  In addition, each port is bridged to the Switch Fabric through
a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.

Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows.  The Ethernet DMA channels use
descriptors set up in memory, the memory map of the device, and access via
the Switch Fabric.  The Ethernet Controller’s DMA arbiter handles
arbitration for the Switch Fabric.  The Controller also has a register bus
interface for register accesses and status monitor control.

The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes.  The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs.  Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each

Ethernet port uses its transmit and receive DMA channels to manage data
flows through buffer descriptors that are predefined by the system (the
descriptors can exist anywhere in the system memory map).  These
descriptors are data structures that point to buffers filled with data
ready to transmit over Ethernet, or they point to empty buffers ready to
receive data from Ethernet.
Signed-off-by: NAlexandre Bounine <Alexandre.Bounine@tundra.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

[PATCH] sundance: solve host error problem in low performance embedded system when continune down and up

Solve host error problem in low performance embedded system when continune
down and up.  It will cause IP100A DMA TargetAbort.  So we need more safe
process to up and down IP100A with wait hardware completely stop and software
cur_tx/ dirty_tx/cur_task/last_tx be clear.
Signed-off-by: NJesse Huang <jesse@icplus.com.tw>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ia64:

 drivers/built-in.o(.text+0xd9a72): In function `e1000_xmit_frame':
 : undefined reference to `csum_ipv6_magic'

Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch requires the new support for configurable PHY
interfaces.

Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent
Signed-off-by: NAndrew Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The patch inlined below adds NET_POLL_CONTROLLER support for gianfar network driver, slightly modified wrt the comments from Andy Fleming.

 drivers/net/gianfar.c |   33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)
Signed-off-by: NVitaly Wool <vwool@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Clean-up some warnings from missing return code checks, mostly from
calling pci_enable_device during a PCI resume.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SoftMAC contains a number of debug-type messages that continue to print
even when debugging is turned off. This patch substitutes dprintkl for
printkl for those lines.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the softmac version of bcm43xx, the core scan logs whether each core is
enabled or disabled. This information is useless as one of the next steps
is to enable all cores. This patch removes this output from the log.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the periodic work function in bcm43xx was converted for voluntary preemption
to reduce latency, a new function was created to estimate the "badness" of
each step, and this quantity was used to determine if preemption should be
enabled when periodic work was undertaken. This concept was quite useful
while debugging of periodic work was in progress. Now that this routine
seems to be working correctly, it is time to simplify the code. This
patch keeps the functionality intact, but simplifies the code.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most contributed and Signed-off-by: Andrew Morton <akpm@osdl.org>
with some from me as well.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Correct initial and close hardware step.  In some embedded system down and up
IP100A will cause DMA crash.  We add some for safe down and up IP100A.
Signed-off-by: NJesse Huang <jesse@icplus.com.tw>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* genphy_update_link is now exported
* Added a fix from ncase@xes-inc.com which changes forcing so it
  only updates the link.  Otherwise, it never tries the lower
  values, since it is always overwriting the speed/duplex values
  with the current ones, rather than the intended ones.
* Fixed a bug where bringing up a PHY with no link caused it to
  timeout, and enter forcing mode.  Once in forcing mode,
  plugging in the link didn't autonegotiate.  Now the AN state
  detects the lack of link, and enters the NO_LINK state.  AN
  only times out if the link is up and AN fails
* Cleaned up the PHY_AN case, reducing one level of indentation
  for the timeout code.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix TX Pause bug (reset_tx, intr_handler).  When MaxCollisions occurred, need
to re-enable Tx.  But just after re-enable, MaxCollisions maybe occurred again
and with TxStatusOverflow.  This will cause driver can't check new
MaxCollisions to re-enable Tx again, because TxStatusOverflow.  For this
reason, after re-enable Tx, we need to make sure Tx was actually enabled.
Signed-off-by: NJesse Huang <jesse@icplus.com.tw>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

For patent issue need to remove TxStartThresh and RxEarlyThresh.  This patent
is cut-through patent.  If use this function, Tx will start to transmit after
few data be move in to Tx FIFO.  We are not allow to use those function in
DFE530/DFE550/DFE580/DL10050/IP100/IP100A.  It will decrease a little
performance.
Signed-off-by: NJesse Huang <jesse@icplus.com.tw>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove the code to change the E8390_CMD register from ei_watchdog().
The 8390-page is always 0 outside the spin_lock.

Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support for the new mcp67 device into forcedeth.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>