The previous code had hardcoded the PHY_INTERFACE_MODE_MII of phy_connect.
So some Gigabit PHYs will not behave correctly.
The patch adds the phy_interface in sh_eth_plat_data, so we can select
the phy interface.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SH7763 has GETHER. So the specification of some registers differs than
other CPUs. This patch removes almost #ifdef of CONFIG_CPU_SUBTYPE_SH7763.
Then we are able to add other CPU's GETHER easily.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The defination is hardcoded in this driver for some CPUs. This patch
modifies to get resource of TSU address from platform_device.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous code cannot handle the ETHER and GETHER both as same time
because the definitions of register was hardcoded.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I intend to turn struct flowi into a union of AF specific flowi
structs.  There will be a common structure that each variant includes
first, much like struct sock_common.

This is the first step to move in that direction.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PFC configuration is not cleared until the device is reset. This
has not been a problem because setting DCB attributes forced a
hardware reset. Now that we no longer require this reset to occur
PFC remains configured even after being disabled until the
device is reset.

This removes a goto in the PFC hardware set routines for 82598 and
82599 devices that was short circuiting the clear.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implemented ixgbe_ndo_set_vf_bw function which is being used by iproute2
tool. In addition, updated ixgbe_ndo_get_vf_config function to show the
actual rate limit to the user.

The rate limitation can be configured only when the link is up and the
link speed is 10Gb.
The rate limit value can be 0 or ranged between 11 and actual link
speed measured in Mbps. A value of '0' disables the rate limit for
this specific VF.

iproute2 usage will be 'ip link set ethX vf Y rate Z'.
After the command is made, the rate will be changed instantly.
To view the current rate limit, use 'ip link show ethX'.

The rates will be zeroed only upon driver reload or a link speed change.

This feature is being supported by 82599 and X540 devices.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

DCB provides a guaranteed bandwidth in the case with 0%
bandwidth then no bandwidth is guaranteed. However the
traffic class should still be able to transmit traffic.
For this to work the traffic class must be given the
minimum credits required to send a frame.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

VF Free Running Timer register name missing an F.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updates the PHY setup code to support 100Mbps capable PHYs
as well as 10G and 1Gbps.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF mailbox polling for acks and messages would reset the timer to zero
on a timeout. Under heavy load a timeout may actually occur without being
the result of an error and when this occurs it is not practical to perform
a full VF driver reset on every message timeout. Instead, just return an
error (which is already done) and the VF driver will have an opportunity
to retry the operation.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

DCB settings are cleared in the hardware across link events
during ifup ixgbe reprograms the hardware for DCB if it is
enabled. Now that we have two modes CEE or IEEE we need to
use the correct set of configuration data.

This patch checks the dcbx_cap bits and then enables the
device in the correct mode.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support to use the priority assignment
table in the ieee_ets structure to map priorities to
traffic classes. Previously ixgbe only supported a
1:1 mapping. Now we can enable and disable hardware
DCB support when multiple traffic classes are actually
being used. This allows the default case all priorities
mapped to traffic class 0 to work in normal hardware
mode and utilize the full packet buffer.

This patch does not address putting the hardware in
4TC mode so packet buffer space may be underutilized
in this case. A follow up patch can address this
optimization. But at least we have the hooks to do
this now.

Also CEE will behave as it always has and map priorities
1:1 with traffic classes.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The patch below  allowed IEEE 802.1Qaz and CEE DCB hardware
configurations to use common hardware set routines,

commit 88eb696cc6a7af8f9272266965b1a4dd7d6a931b
Author: John Fastabend <john.r.fastabend@intel.com>
Date:   Thu Feb 10 03:02:11 2011 -0800

    ixgbe: DCB, abstract out dcb_config from DCB hardware configuration

However the case when CEE link strict and group strict
are set was missed and are currently being mapped
incorrectly in some configurations.

This patch resolves this.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RSS had previously been disabled when DCB was enabled because
DCB was single queued per traffic class. Now that DCB implements
multiple Tx/Rx rings per traffic class enable RSS.

Here RSS hashes across the queues in the traffic class.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain.@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the ndo_tc_setup to ixgbe. By default we set
the device to use strict priority.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain.@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This enables multiple {Tx|Rx} rings per traffic class while in DCB
mode. In order to get this working as expected the tc_to_tx net
device mapping is configured as well as the prio_tc_map.

skb priorities are mapped across a range of queue pairs to get
a distribution per traffic class. The maximum number of
queue pairs used while in DCB mode is capped at 64. The hardware
max is actually 128 queues but 64 is sufficient for now and
allocating more seemed a bit excessive. It is easy enough to
increase the cap later if need be.

To get the 802.1Q priority tags inserted correctly ixgbe was
previously using the skb queue_mapping field to directly set
the 802.1Q priority. This no longer works because we have removed
the 1:1 mapping between queues and traffic class. Each ring
is aligned with an 802.1Qaz traffic class so here we add an
extra field to the ring struct to identify the 802.1Q traffic
class. This uses an extra byte of the ixgbe_ring struct
fortunately there was a 2byte hole,

struct ixgbe_ring {
        void *                     desc;                 /*     0     8 */
        struct device *            dev;                  /*     8     8 */
        struct net_device *        netdev;               /*    16     8 */
        union {
                struct ixgbe_tx_buffer * tx_buffer_info; /*           8 */
                struct ixgbe_rx_buffer * rx_buffer_info; /*           8 */
        };                                               /*    24     8 */
        long unsigned int          state;                /*    32     8 */
        u8                         atr_sample_rate;      /*    40     1 */
        u8                         atr_count;            /*    41     1 */
        u16                        count;                /*    42     2 */
        u16                        rx_buf_len;           /*    44     2 */
        u16                        next_to_use;          /*    46     2 */
        u16                        next_to_clean;        /*    48     2 */
        u8                         queue_index;          /*    50     1 */
        u8                         reg_idx;              /*    51     1 */
        u16                        work_limit;           /*    52     2 */

        /* XXX 2 bytes hole, try to pack */

        u8 *                       tail;                 /*    56     8 */
        /* --- cacheline 1 boundary (64 bytes) --- */

Now we can set the VLAN priority directly and it will be
correct. User space can indicate the 802.1Qaz priority
using the SO_PRIORITY setsocket() option and QOS layer will
steer the skb to the correct rings. Additionally using
the multiq qdisc with a queue_mapping action works as
well.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove ixgbe_fcoe_getapp() and use the generic kernel
routine instead. Also add application priority to the
kernel maintained list on setapp so applications and
stacks can query the value.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement ieee_setapp dcbnl ops in ixgbe. This is required
to setup FCoE which requires dedicated resources. If the
app data is not for FCoE then no action is taken in ixgbe
except to add it to the dcb_app_list.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This implements dcbnl get and set capabilities ops. The
devices supported by ixgbe can be configured to run in
IEEE or CEE modes but not both.

With the DCBX set capabilities bit we add an explicit
signal that must be used to toggle between these modes.
This patch adds logic to fail the CEE command set_hw_all()
which programs the device with a CEE configuration if
the CEE caps bit is not set. Similarly, IEEE set
commands will fail if the IEEE caps bit is not set. We
allow most CEE config set commands to occur because they
do not touch the hardware until set_hw_all() is called.

The one exception to the above is the {set|get}app routines.
These must always be protected by caps bits to ensure
side effects do not corrupt the current configured mode.

By requiring the caps bit to be set correctly we can
maintain a consistent configuration in the hardware
for CEE or IEEE modes and prevent partial hardware
configurations that may occur if user space does
not send a complete IEEE or CEE configurations.

It is expected that user space will signal a DCBX mode
before programming device.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates igb version to 3.0.6.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch add DMA Coalescing which is a power-saving feature that
coalesces DMA writes in order to stay in a low-power state as much
as possible.  Feature is disabled by default.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions and functions pointers to accommodate
differences between NVM interfaces and options for i350 devices,
82580 devices and the rest.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the EEE feature for i350 devices, enabled by default.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the driver string to match the PF driver string format.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel version string is off by a major version number since
new silicon was just introduced and also uses the wrong format for
the version postfix.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver doesn't support Wake-on-ARP, so don't advertise through ethtool
that it does.

Cleanup some coding style issues in the same functions.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If/when an OEM enables MACsec in the 82579 EEPROM, disable jumbo frames
support in the driver due to an interoperability issue in hardware that
prevents jumbo packets from being transmitted or received.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When PHY reset is intentionally blocked on 82577/8/9, do not toggle the
LANPHYPC value bit (essentially performing a hard power reset of the
device) otherwise the PHY can be put into an unknown state.

Cleanup whitespace in the same function.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The link can be unexpectedly dropped when the timer for entering EEE low-
power-idle quiet state expires too soon.  The timer needs to be extended
from 196usec to 200usec after every LCD (PHY) reset to prevent this from
happening.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With some PHYs supported by this driver, link establishment can take a
little longer when connected to certain switches.  Extend the timeout to
reduce the number of false diagnostic failures, and cleanup a code style
issue in the same function.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a report and patch originally submitted by Prasanna Panchamukhi.

Use dev_kfree_skb_irq() in e1000_clean_jumbo_rx_irq() since this latter
function is called only in interrupt context.  This avoids "Warning:
kfree_skb on hard IRQ" messages.

Cc: "Prasanna S. Panchamukhi" <prasanna.panchamukhi@riverbed.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removed Tx hang detection mechanism from ixgbevf.
This mechanism has no affect and can cause false alarm messages in some
cases. Especially when VF Tx rate limit is turned on.

The same mechanism was removed recently from igbvf.
Signed-off-by: NLior Levy <lior.levy@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Jesse Gross <jesse@nicira.com>

This switches the ixgb driver to use the new VLAN interfaces.
In doing this, it completes the work begun in
ae54496f allowing the use of
hardware VLAN insertion without having a VLAN group configured.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 5750 ASIC rev was never released as a PCI device.  It only exists as
a PCIe device.  This patch removes the code that supports the former
configuration.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the function that initializes the link configuration
closer to the place where the rest of the phy code is initialized.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>