A hanging has been detected in ohci-at91 while going in suspend to ram. This is
due to asynchronous operations between ohci reset and ohci clocks shutdown.
This patch adds the reading of the control register between the reset of the
ohci and clocks stop. This "flush the writes" idea was taken from ohci-hcd.c
file (ohci_shutdown() function).
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Modify both host and gadget USB drivers for at91sam9g10.
This add a clock management equivalent to at91sam9261 on usb drivers.
It also add the way of handling gadget pull-ups (like the at91sam9261).
Signed-off-by: NHong Xu <hong.xu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

At91sam9g45 series has a set of high speed USB interfaces.
The host driver is an EHCI with its companion OHCI. OHCI is
always handled by ohci-at91.c.
This wrapper is just modified to allow IRQ sharing
between two controllers.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently, the vbus_pin assignment loop is limited by the value of the "ports"
variable in the platform data.  Now that the vbus_pin array is no longer
flexible, we can use its actual size.
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled.  Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub.  This approach turns out to be subject to races, resulting
in unnecessary polling.

The patch does away with the method entirely.  Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present.  This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file.  Remove these unnecessary
includes.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Looks like usb_put_hcd was missing. Also, make an always-zero function
return void.
Signed-off-by: NPete Zaitcev <zaitcev@yahoo.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit e8721549.

Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver.  Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example

	http://lkml.org/lkml/2008/7/5/236

for an analysis.

The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled.  Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub.  This approach turns out to be subject to races, resulting
in unnecessary polling.

The patch does away with the method entirely.  Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present.  This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed.  These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.

Until now these jobs have been carried out when the root hub is
resumed, not when the controller is.  Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed.  But this is wasteful and
unnecessary.

To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers.  They can call the new routine instead of
resuming their root hubs.  And ohci-pci.c can call it instead of using
its own special-purpose handler.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable USB HCDs,
to allow re-enable auto loading.

[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update the ohci-at91 bus glue to start understanding about the per-port
power switch GPIOs it's given (on the sam9263-ek and potentially other
boards).  For the moment this just claims them and forces them active
(assuming active-low power enables) whenever the HCD is loaded.

The assumption is still that board setup configures the GPIOs.  Using
gpio_request() tracks actual usage and guards against conflict.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The AT91SAM9261 needs to activate an AHB clock (HCK0) to use the USB Host
controller. Previously clock.c would just enable it at startup, but now
all the unused clocks are automatically disabled.

Based on patch from Nicolas Ferre.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The attached patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 USB Host driver.

It should resolve these kernel messages:
  Unbalanced IRQ x wake disable
  BUG: warning at kernel/irq/manage.c:167/set_irq_wake()

(The original code was debugged before a bug in the genirq wakeup irq
logic was fixed by adding the IRQ wake enable/disable refcounting.
Not all code yet uses the bugfixed model.)
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The previous model had the module_init & module_exit function in the
bus glue .c files themselves. That's a problem if several glues need
to be selected at once and the driver is built has module. This case
is quite common in embedded system where you want to handle both the
integrated ohci controller and some extra controller on PCI.

The ohci-hcd.c file now provide the module_init & module_exit and
appropriate driver registering/unregistering is done conditionally,
using #ifdefs.
Signed-off-by: NSylvain Munaut <tnt@246tNt.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove a warning about an unused variable in the OHCI bus glue for at91.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace
(space before tab, at end of line) as well as the obsolete inline changelog.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This includes two one-liners forwarded to me for the OHCI support on at91:

 - KB920x (and other boards with CPUs in non-BGA packages) need a slightly
   different way to say "ignore that port, it's not pinned out";

 - On resume, if we turn clocks on, record that we did so.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If some problem occurs during ehci startup, for instance, request_irq fails,
echi hcd driver tries it best to cleanup, but fails to unregister reboot
notifier, which in turn leads to crash on reboot/poweroff.

The following patch resolves this problem by not using reboot notifiers
anymore, but instead making ehci/ohci driver get its own shutdown method.  For
PCI, it is done through pci glue, for everything else through platform driver
glue.

One downside: sa1111 does not use platform driver stuff, and does not have its
own shutdown hook, so no 'shutdown' is called for it now.  I'm not sure if it
is really necessary on that platform, though.
Signed-off-by: NAleks Gorelov <dared1st@yahoo.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This teaches OHCI to use the root hub status change (RHSC) IRQ, bypassing
root hub timers most of the time and switching over to the "new" root hub
polling scheme.  It's complicated by the fact that implementations of OHCI
trigger and ack that IRQ differently (the spec is vague there).

Avoiding root hub timers helps mechanisms like "dynamic tick" leave the
CPU in lowpower modes for longer intervals.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OHCI updates for AT91 series processors:

 - Get ready for at91sam926x processors (ARMv5tej not ARMv4t)

 - Suspend/resume support now behaves properly

 - In "standby" mode, OHCI can be a source of system wakeup events
   (remote wakeup, device connect/disconnect, etc)

And minor cleanups.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

AT91: the two USB drivers (OHCI, UDC) got out of sync with various
usbcore and driver model PM updates; fix.

Also minor fixes to ohci:  whitespace/style, MODULE_ALIAS so coldplug works
using /sys/.../modalias, and turn off _both_ clocks during suspend.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds support for OHCI on AT91rm9200 based boards.

Possibly of interest here is the way this uses <linux/clk.h> to
gate clocks on/off during system pm state transitions.  That's
typical for non-PCI systems.  Some can go further; Mini-A host
side connectors enable ID-pin sensing.

From: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>