struct soc_camera_link imx074_link in board-ap4evb.c doesn't have
to be global.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Name the SDHI1 instance sh_sdhi1_info to be consistent with sh_sdhi0_info.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

USB1 can use IRQ interrupt and notify function for usbhs driver,
but USB0 is using polling for it.
The priority of usbhs devices order USB1 > USB0 is good idea
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

- usb0 pipe is same as default. own pipe config is not needed
- usb1 lost get_id function
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

While SH7377 and others were updated to properly use SCIFA/B port types,
SH7367 was left behind. Fix it up accordingly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Initialize ->irq_set_wake() in gic_arch_extn to unbreak wake
up from the KEYSC device on AG5EVM in case of Suspend-to-RAM.

Without this patch "echo mem > /sys/power/state" and a key
press results in the following message on resume:

WARNING: at kernel/irq/manage.c:507 irq_set_irq_wake+0x7c/0xd8()
Unbalanced IRQ 103 wake disable
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch updates the board specific USB support
code for the sh7372 Mackerel board.

With this patch applied port CN22 is driven by the
recently added renesas_usbhs driver using the first
USB controller included in sh7372 aka USBHS0.

Hotplugging of USBHS0 unfortunately has to be
handled by software polling. The sh7372 SoC itself
obviously supports hotplug notification by IRQ but
on the Mackerel board this IRQ happens to be used
for the touch screen.

Also fix the pinmux configuration to avoid setting
up unused pins and fix minor spelling errors.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add a flag for SDHI1 to enable SDIO IRQ, and remove DMA Engine
slave id:s to disable DMA as a workaround.

Tested on sh73a0/AG5EVM with a BCM4318-based SDIO card.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

On sh7372 the card-detection pin of SDHI0 can also produce interrupts,
when configured as GPIO. Use this feature to power down SDHI0, when no
card is plugged in.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

renesas_usbhs driver can use external interrupt mode
(which come from USB-PHY) or autonomy mode (it use own interrupt)
for detecting connection/disconnection when Function.
And it will be power OFF while it has been disconnecting
if external interrupt mode is selected.

mackerel board has 2 USB ports.

But we can not use external interrupt mode
on CN22 USB0 port which is only for USB Function.
IRQ7-PORT40 is already used by Touchscreen,
and USB-PHY needs IRQ7-PORT167.
It is impossible to use IRQ7 demux on mackerel.

We can use external interrupt mode USB-Function on "USB1".
USB1 can become Host by r8a66597, and become Function by renesas_usbhs.
But don't select both drivers in same time.
These 2 drivers are not supporting IRQ SHARD.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This obviously should have been 0xe6d500ff, fix it up accordingly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

renesas_usbhs is remake version of r8a66597
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Based on the patch by Takanari Hayama <taki@igel.co.jp>

Add the necessary platform data to add MERAM functionality to LCDC

Includes platform data for both the AP4EVB and mackerel
Signed-off-by: NDamian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This makes it possible to leave DMA slave IDs in the platform data
at default 0 value without hitting DMA channel allocation error paths.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This makes it possible to leave DMA slave IDs in the platform data
at default 0 value without hitting DMA channel allocation error paths.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SDHI0 and SDHI1 slave ids for RX and TX to enable
DMA Engine support for SDHI on the AG5EVM board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Simply add MMCIF slave ids for RX and TX to enable
DMA Engine support for the AG5EVM board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SY-DMAC support via shdma.c to the sh73a0 SoC
including slave ids, platform data and clock bindings.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch ties in the previously added sh7372 sleep
mode known as Core Standby together with the shared
SH-Mobile ARM CPUIdle implementation.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds a shared SH-Mobile ARM specific CPUIdle
implementation supporting WFI only at this point. It
serves as a common point for late registration of the
arch-specific CPUIdle code, and supports adding extra
sleep modes using the callback shmobile_cpuidle_setup()
together with shmobile_cpuidle_modes[].
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add sh7372 Core Standby sleep mode support and tie it
in with the shared SH-Mobile ARM suspend code.

The Core Standby mode is the lightest sh7372-specific
sleep mode, cutting power to the ARM core excluding the
L2 cache. Any interrupt source can be used for wakeups.

The low level portion of this code is based on the
TI OMAP sleep code in sleep34xx.S, thanks to them.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds a simple Suspend-to-RAM implementation
for SH-Mobile ARM. The struct shmobile_suspend_ops are
kept global to allow cpu-specific code to override
the callbacks if needed.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use soc_camera_platform helper functions to dynamically manage the
camera device.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SDHI0 and SDHI1 support to the AG5EVM board
including platform data, pinmux configuration
and clock bindings.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch reverts "ARM: mach-shmobile: sh7372 SDHI vector merge" and
supplies 3 IRQ resources for each SDHI block.

Some blocks have a 4th IRQ, but this is used for DRM feathres
that I do not have access tot he documentation for and are almost
certainly tainted by licensing issues. So the 4th IRQ is not
hooked-up even if it exists.

Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the struct resources for DSI0 to include the
hardware block name. Purely cosmetic, makes /proc/iomem
look slightly better.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix the case of too late twd_base initialization for SMP
on sh73a0 which bas been broken because sh73a0 specific
smp_prepare_cpu() and percpu_timer_setup() changed order
in the commits:

05c74a6c
c413521e

Without this fix the sh73a0 SMP kernel panics on boot.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Git commit f4117ac9
introduced PLAT_PHYS_OFFSET, but headsmp.S was left
unchanged which results in a compile error:

  AS      arch/arm/mach-shmobile/headsmp.o
arch/arm/mach-shmobile/headsmp.S: Assembler messages:
arch/arm/mach-shmobile/headsmp.S:27: Error: undefined symbol `secondary_startup' in operation
arch/arm/mach-shmobile/headsmp.S:27: Error: undefined symbol `PHYS_OFFSET' in operation
make[1]: *** [arch/arm/mach-shmobile/headsmp.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the sh7372 clock code to set the RT side
set of MSTP bits to a fixed disabled state.

The sh7372 SoC contains two sets of MSTP bits,
one for the ARM (SYS) side, and one for the
SH4AL-DSP (RT) side. The actual clock associated
with the MSTP bit will only be stopped when both
sides have set the MSTP bit to disabled mode.

Some MSTP bits are enabled by default after
hardware reset, so this patch adjusts the code
to disable all MSTP bits associated with the RT
side to allow the SYS side to have full control.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The PLLC2 clock on AP4 systems does not need to run constantly to be
able to use HDMI. The HDMI hotplug interrupt works without the PLL
too, after which all the necessary clocks will be turned on by the
runtime PM.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add DMA mode support for the MMCIF controller on mackerel.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remember to also check for the CONFIG_MMC_SH_MMCIF_MODULE option
for the case of a modular MMCIF driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Export the following sh7377 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Export the following sh7372 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Export the following sh7367 multimedia hardware blocks
using UIO: VPU, VEU[0-3], VEU2H, JPU and SPU1
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the sh7377 serial port types to make use of
PORT_SCIFA and PORT_SCIFB. This makes the software
match the sh7377 data sheet.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* Set receive enable and transmit enable bits of SCASCR0 (E6C400089).
  Values previously written to this register was bogus.

  Curiously earlyprintk works with the previous code.

* Remove duplicate initialisation of GPIO port 152, SCIFA0_TXD (0xE6053098).
  This should have no effect other than to very slightly reduce the amount of
  code.
Reported-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>