Interface iteration in mac80211 can be done without holding any
locks because I converted it to RCU. Initially, I thought this
wouldn't be needed for ieee80211_iterate_active_interfaces but
it's turning out that multi-BSS AP support can be much simpler
in a driver if ieee80211_iterate_active_interfaces can be called
without holding locks. This converts it to use RCU, it adds a
requirement that the callback it invokes cannot sleep.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch restructures the Rx handlers chain by incorporating previously
handlers ieee80211_rx_h_802_1x_pae and ieee80211_rx_h_drop_unencrypted
into ieee80211_rx_h_data, already in 802.3 form. this scheme follows more
precisely after the IEEE802.11 data plane archituecture, and will prevent
code duplication to IEEE8021.11n A-MSDU handler.

added function:
 - ieee80211_data_to_8023: transfering 802.11 data frames to 802.3 frame
 - ieee80211_deliver_skb: delivering the 802.3 frames to upper stack
eliminated handlers:
 - ieee80211_rx_h_drop_unencrypted: now function ieee80211_drop_unencrypted
 - ieee80211_rx_h_802_1x_pae: now function ieee80211_802_1x_pae
changed handlers:
 - ieee80211_rx_h_data: now contains calls to four above function
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The scan code in mac80211 makes the software scan assumption in various
places. For example, we stop the Tx queue during a software scan so that
all the Tx packets will be queued by the stack. We also drop frames not
related to scan in the software scan process. But these are not true for
hardware scan.

Some wireless hardwares (for example iwl3945/4965) has the ability to
perform the whole scan process by hardware and/or firmware. The hardware
scan is relative powerful in that it tries to maintain normal network
traffic while doing a scan in the background. Some drivers (i.e iwlwifi)
do provide a way to tune the hardware scan parameters (for example if the
STA is associated, what's the max time could the STA leave from the
associated channel, how long the scans get suspended after returning to
the service channel, etc). But basically this is transparent to the
stack. mac80211 should not stop Tx queues or drop Rx packets during a
hardware scan.

This patch resolves the above problem by spliting the current scan
indicator local->sta_scanning into local->sta_sw_scanning and
local->sta_hw_scanning. It then changes the scan related code to be aware
of hardware scan or software scan in various places. With this patch,
iwlwifi performs much better in the scan-while-associated condition and
disable_hw_scan=1 should never be required.

Cc: Mohamed Abbas <mohamed.abbas@intel.com>
Cc: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This only includes fixing the space-indented lines and
removing one unneeded else after the goto.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I moved the call to kmalloc() from the *t declaration into
the code (this is confusing when a variable is initialized
with the result of some call) and removed unneeded comment
near the error path. Just like I did with the neigh ctl-s.

Besides, I fixed the goto's and the labels - they were indented
with spaces :(
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The appropriate path is prepared right inside this function. It
is prepared similar to how the ctl tables were.

Since the path is modified, it is put on the stack, to avoid
possible races with multiple calls to neigh_sysctl_register() : it
is called by protocols and I didn't find any protection in this
case. Did I overlooked the rtnl lock?.

The stack growth of the neigh_sysctl_register() is 40 bytes. I
believe this is OK, since this is not that much and this function
is not called with the deep stack (device/protocols register).

The device's name is stored on the template to free it later.

This will help with the net namespaces, as each namespace should
have its own set of these ctls.

Besides, this saves ~350 bytes from the neigh template :)
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This mainly removes the err variable, as this call always
return the same error code (-ENOBUFS).

Besides, I moved the call to kmalloc() from the *t declaration
into the code (this is confusing when a variable is initialized
with the result of some call) and removed unneeded comment near
the error path.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the core.

 * add the ctl_table_header on the struct net;
 * make the unix_sysctl_register and _unregister clone the table;
 * moves calls to them into per-net init and exit callbacks;
 * move the .data pointer in the proper place.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike previous ones, this patch is useful by its own,
as it decreases the vmlinux size :)

But it will be used later, when the per-namespace sysctl
is added.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will make all the sub-namespaces always use the
default value (10) and leave the tuning via sysctl
to the init namespace only.

Per-namespace tuning is coming.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the struct net * argument to both of them to use in
the future. Also make the register one return an error code.

It is useless right now, but will make the future patches
much simpler.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the netmask/prefix-length of an IPsec SPD entry is not included in
any of the SPD related audit messages.  This can cause a problem when the
audit log is examined as the netmask/prefix-length is vital in determining
what network traffic is affected by a particular SPD entry.  This patch fixes
this problem by adding two additional fields, "src_prefixlen" and
"dst_prefixlen", to the SPD audit messages to indicate the source and
destination netmasks.  These new fields are only included in the audit message
when the netmask/prefix-length is less than the address length, i.e. the SPD
entry applies to a network address and not a host address.

Example audit message:

 type=UNKNOWN[1415] msg=audit(1196105849.752:25): auid=0 \
   subj=root:system_r:unconfined_t:s0-s0:c0.c1023 op=SPD-add res=1 \
   src=192.168.0.0 src_prefixlen=24 dst=192.168.1.0 dst_prefixlen=24

In addition, this patch also fixes a few other things in the
xfrm_audit_common_policyinfo() function.  The IPv4 string formatting was
converted to use the standard NIPQUAD_FMT constant, the memcpy() was removed
from the IPv6 code path and replaced with a typecast (the memcpy() was acting
as a slow, implicit typecast anyway), and two local variables were created to
make referencing the XFRM security context and selector information cleaner.
Signed-off-by: NPaul Moore <paul.moore@hp.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on a previous patch by Gerrit Renker.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The user interface is: register_net_sysctl_table and
unregister_net_sysctl_table.  Very much like the current
interface except there is a network namespace parameter.

With this any sysctl registered with register_net_sysctl_table
will only show up to tasks in the same network namespace.

All other sysctls continue to be globally visible.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the basic infrastructure for per namespace sysctls.

A list of lists of sysctl headers is added, allowing each namespace to have
it's own list of sysctl headers.

Each list of sysctl headers has a lookup function to find the first
sysctl header in the list, allowing the lists to have a per namespace
instance.

register_sysct_root is added to tell sysctl.c about additional
lists of sysctl_headers.  As all of the users are expected to be in
kernel no unregister function is provided.

sysctl_head_next is updated to walk through the list of lists.

__register_sysctl_paths is added to add a new sysctl table on
a non-default sysctl list.

The only intrusive part of this patch is propagating the information
to decided which list of sysctls to use for sysctl_check_table.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By doing this we allow users of register_sysctl_paths that build
and dynamically allocate their ctl_table to be simpler.  This allows
them to just remember the ctl_table_header returned from
register_sysctl_paths from which they can now find the
ctl_table array they need to free.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a number of modules that register a sysctl table
somewhere deeply nested in the sysctl hierarchy, such as
fs/nfs, fs/xfs, dev/cdrom, etc.

They all specify several dummy ctl_tables for the path name.
This patch implements register_sysctl_path that takes
an additional path name, and makes up dummy sysctl nodes
for each component.

This patch was originally written by Olaf Kirch and
brought to my attention and reworked some by Olaf Hering.
I have changed a few additional things so the bugs are mine.

After converting all of the easy callers Olaf Hering observed
allyesconfig ARCH=i386, the patch reduces the final binary size by 9369 bytes.

.text +897
.data -7008

   text    data     bss     dec     hex filename
   26959310        4045899 4718592 35723801        2211a19 ../vmlinux-vanilla
   26960207        4038891 4718592 35717690        221023a ../O-allyesconfig/vmlinux

So this change is both a space savings and a code simplification.

CC: Olaf Kirch <okir@suse.de>
CC: Olaf Hering <olaf@aepfle.de>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kill the defines again, convert to the new checksum helper names and
remove the dependency of NET_ACT_NAT on NETFILTER.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows to get rid of the CONFIG_NETFILTER dependency of NET_ACT_NAT.
This patch redefines the old names to keep the noise low, the next patch
converts all users.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes a redundant test for unexpected packet types. In dccp_rcv_state_process
it is tested twice whether a DCCP-server has received a CloseReq (Step 7):

 * first in the combined if-statement,
 * then in the call to dccp_rcv_closereq().

The latter is necesssary since dccp_rcv_closereq() is also called from
__dccp_rcv_established().

This patch removes the duplicate test.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the necessary state transitions for the two forms of passive-close

 * PASSIVE_CLOSE    - which is entered when a host   receives a Close;
 * PASSIVE_CLOSEREQ - which is entered when a client receives a CloseReq.

Here is a detailed account of what the patch does in each state.

1) Receiving CloseReq

  The pseudo-code in 8.5 says:

     Step 13: Process CloseReq
          If P.type == CloseReq and S.state < CLOSEREQ,
              Generate Close
              S.state := CLOSING
              Set CLOSING timer.

  This means we need to address what to do in CLOSED, LISTEN, REQUEST, RESPOND, PARTOPEN, and OPEN.

   * CLOSED:         silently ignore - it may be a late or duplicate CloseReq;
   * LISTEN/RESPOND: will not appear, since Step 7 is performed first (we know we are the client);
   * REQUEST:        perform Step 13 directly (no need to enqueue packet);
   * OPEN/PARTOPEN:  enter PASSIVE_CLOSEREQ so that the application has a chance to process unread data.

  When already in PASSIVE_CLOSEREQ, no second CloseReq is enqueued. In any other state, the CloseReq is ignored.
  I think that this offers some robustness against rare and pathological cases: e.g. a simultaneous close where
  the client sends a Close and the server a CloseReq. The client will then be retransmitting its Close until it
  gets the Reset, so ignoring the CloseReq while in state CLOSING is sane.

2) Receiving Close

  The code below from 8.5 is unconditional.

     Step 14: Process Close
          If P.type == Close,
              Generate Reset(Closed)
              Tear down connection
              Drop packet and return

  Thus we need to consider all states:
   * CLOSED:           silently ignore, since this can happen when a retransmitted or late Close arrives;
   * LISTEN:           dccp_rcv_state_process() will generate a Reset ("No Connection");
   * REQUEST:          perform Step 14 directly (no need to enqueue packet);
   * RESPOND:          dccp_check_req() will generate a Reset ("Packet Error") -- left it at that;
   * OPEN/PARTOPEN:    enter PASSIVE_CLOSE so that application has a chance to process unread data;
   * CLOSEREQ:         server performed active-close -- perform Step 14;
   * CLOSING:          simultaneous-close: use a tie-breaker to avoid message ping-pong (see comment);
   * PASSIVE_CLOSEREQ: ignore - the peer has a bug (sending first a CloseReq and now a Close);
   * TIMEWAIT:         packet is ignored.

   Note that the condition of receiving a packet in state CLOSED here is different from the condition "there
   is no socket for such a connection": the socket still exists, but its state indicates it is unusable.

   Last, dccp_finish_passive_close sets either DCCP_CLOSED or DCCP_CLOSING = TCP_CLOSING, so that
   sk_stream_wait_close() will wait for the final Reset (which will trigger CLOSING => CLOSED).
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds two auxiliary states to deal with passive closes:
  * PASSIVE_CLOSE    (reached from OPEN via reception of Close)    and
  * PASSIVE_CLOSEREQ (reached from OPEN via reception of CloseReq)
as internal intermediate states.

These states are used to allow a receiver to process unread data before
acknowledging the received connection-termination-request (the Close/CloseReq).

Without such support, it will happen that passively-closed sockets enter CLOSED
state while there is still unprocessed data in the queue; leading to unexpected
and erratic API behaviour.

PASSIVE_CLOSE has been mapped into TCPF_CLOSE_WAIT, so that the code will
seamlessly work with inet_accept() (which tests for this state).

The state names are thanks to Arnaldo, who suggested this naming scheme
following an earlier revision of this patch.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a nasty bug: dccp_send_reset() is called by both DCCPv4 and DCCPv6, but uses
inet_sk_rebuild_header() in each case. This leads to unpredictable and weird behaviour:
under some conditions, DCCPv6 Resets were sent, in other not.

The fix is to use the AF-independent rebuild_header routine.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch was based on another made by Gerrit Renker, his changelog was:

    ------------------------------------------------------
The patch set migrates TFRC TX history to a singly-linked list.

The details are:
 * use of a consistent naming scheme (all TFRC functions now begin with `tfrc_');
 * allocation and cleanup are taken care of internally;
 * provision of a lookup function, which is used by the CCID TX infrastructure
   to determine the time a packet was sent (in turn used for RTT sampling);
 * integration of the new interface with the present use in CCID3.
    ------------------------------------------------------

Simplifications I did:

. removing the tfrc_tx_hist_head that had a pointer to the list head and
  another for the slabcache.
. No need for creating a slabcache for each CCID that wants to use the TFRC
  tx history routines, create a single slabcache when the dccp_tfrc_lib module
  init routine is called.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Skip condition used to be wrong way around which made SACK
processing very broken, missed many blocks because of that.

2) Use highest_sack advancement only if some skbs are already
sacked because otherwise tcp_write_queue_next may move things
too far (occurs mainly with GSO). The other similar advancement
is not problem because highest_sack was previosly put to point
a sacked skb.

These problems were located because of problem report from Matt
Mathis <mathis@psc.edu>.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The

        if (statement)
                WARN_ON(1);

looks much better as

        WARN_ON(statement);
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch includes support for the Intra-Site Automatic Tunnel
Addressing Protocol (ISATAP) per RFC4214. It uses the SIT
module, and is configured using extensions to the "iproute2"
utility. The diffs are specific to the Linux 2.6.24-rc2 kernel
distribution.

This version includes the diff for ./include/linux/if.h which was
missing in the v2.4 submission and is needed to make the
patch compile. The patch has been installed, compiled and
tested in a clean 2.6.24-rc2 kernel build area.
Signed-off-by: NFred L. Templin <fred.l.templin@boeing.com>
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 3rd argument is always zero (according to grep :) Eliminate
it and merge the function with sk_stream_alloc_skb.

This saves 44 more bytes, and together with the previous patch
we have:

add/remove: 1/0 grow/shrink: 0/8 up/down: 183/-751 (-568)
function                                     old     new   delta
sk_stream_alloc_skb                            -     183    +183
ip_rt_init                                   529     525      -4
arp_ignore                                   112     107      -5
__inet_lookup_listener                       284     274     -10
tcp_sendmsg                                 2583    2481    -102
tcp_sendpage                                1449    1300    -149
tso_fragment                                 417     258    -159
tcp_fragment                                1149     988    -161
__tcp_push_pending_frames                   1998    1837    -161
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function seems too big for inlining. Indeed, it saves
half-a-kilo when uninlined:

add/remove: 1/0 grow/shrink: 0/7 up/down: 195/-719 (-524)
function                                     old     new   delta
sk_stream_alloc_pskb                           -     195    +195
ip_rt_init                                   529     525      -4
__inet_lookup_listener                       284     274     -10
tcp_sendmsg                                 2583    2486     -97
tcp_sendpage                                1449    1305    -144
tso_fragment                                 417     267    -150
tcp_fragment                                1149     992    -157
__tcp_push_pending_frames                   1998    1841    -157
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fib_hash: kmalloc + memset conversion to kzalloc
fix to avoid memset entirely.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fib_semantics: kmalloc + memset conversion to kzalloc
fix to avoid memset entirely.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

2007/11/26, Patrick McHardy <kaber@trash.net>:
> How about also switching vmalloc/get_free_pages to GFP_ZERO
> and getting rid of the memset entirely while you're at it?
>

xfrm_hash: kmalloc + memset conversion to kzalloc
fix to avoid memset entirely.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Better place exists in update_send_head (other non-queue related
adjustments are done there as well) which is the only caller of
tcp_advance_send_head (now that the bogus call from mtu_probe is
gone).
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently this size is 16, but as the comment says this
is so only because all the chains (except one) has the
length 1. I think, that some day this may change, so
growing this hash will be much easier.

Besides, symbolic names are read better than magic constants.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sock_wake_async() performs a bit different actions
depending on "how" argument. Unfortunately this argument
ony has numerical magic values.

I propose to give names to their constants to help people
reading this function callers understand what's going on
without looking into this function all the time.

I suppose this is 2.6.25 material, but if it's not (or the
naming seems poor/bad/awful), I can rework it against the
current net-2.6 tree.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This continues from the previous patch and adds support for actively aborting
a DCCP connection, using a Reset Code 2, "Aborted" to inform the peer of an
abortive release.

I have tried this in various client/server settings and it works as expected.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes one FIXME with regard to close when there is still unread data.
The mechanism is implemented similar to TCP: with regard to DCCP-specifics,
a Reset with Code 2, "Aborted" is sent to the peer.

This corresponds in part to RFC 4340, 8.1.1 and 8.1.5.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes a comment which identifies an `issue' with dccp_write_xmit() where there is none.
The comment assumes it is possible that a packet is sent between the calls to

	ccid_hc_tx_send_packet(),
	dccp_transmit_skb(),
	ccid_hc_tx_packet_sent()

(in the above order) in dccp_write_xmit().

I think that this is impossible, since dccp_write_xmit() is always called under lock:

 * when called as dccp_write_xmit(sk, 1) from dccp_send_close(), the socket is locked
   (see code comment above dccp_send_close());
 * when called as dccp_write_xmit(sk, 0) from dccp_send_msg(), it is after lock_sock() has been called;
 * when called as dccp_write_xmit(sk, 0) from dccp_write_xmit_timer(), bh_lock_sock() has been called
   and the if/else statement has made sure that sk_lock.owner is not set;
 * there are no other places where dccp_write_xmit() is called.

Furthermore, the debug statement for printing the sequence number of the packet just sent has been
removed, since the entire list is being printed anyway and so the entry of that number appears last.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code used two different variables to count Acks, one of them redundant.
This patch reduces the number of Ack counters to one.

The type of the Ack counter has also been changed to u32 (twice the range of int);
and the variable has been renamed into `packets_acked' - for consistency with
RFC 3465 (and similarly named variables are used by TCP and SCTP).

Lastly, a slightly less aggressive `maxincr' increment is used (for even Ack Ratios,
maxincr was Ack Ratio/2 + 1 instead of Ack Ratio/2).
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>