On systems with very large numbers (> 1600 or so) of SCSI devices,
cat /proc/scsi/scsi ends up failing with -ENOMEM. This is due to
the show routine simply iterating over all of the devices with
bus_for_each_dev(), and trying to dump all of them into the buffer
at the same time. On my test system (using scsi_debug with 4064 devices),
the output ends up being ~ 632k, far more than kmalloc will typically allow.

This patch defines its own seq_file opreations to iterate over the scsi
devices.The result is that each show() operation only dumps ~ 180 bytes
into the buffer at a time so we don't run out of memory.

If the "Attached devices" header isn't required, we can dump the
sfile->private bit completely.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Bump the driver version.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch fixes an issue seen where an event occurs
which causes the ibmvscsi driver to reset its CRQ. Upon
re-registering its CRQ, it receives H_CLOSED, indicating
the Virtual I/O Server is not yet ready to receive commands.
This resulted in the ibmvscsi driver essentially offlining
the adapter and not recovering. The fix is to re-enable
our interrupt so that when the Virtual I/O server is ready
and sends a CRQ init, we will be able to receive it and
resume initialization of the VSCSI adapter.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Currently the size of the dump generated by the driver is limited
in 4MB, which is insufficient to gather much useful data from the
new 64 bit adapters.

This patch makes the needed changes to increase the dump limit
for the 64 bit adapters to 32MB, or even to a bigger value in the
future, but keeping the current limitations for the legacy 32 bit
adapters.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

1. Add support for Task collector mode.
2. Fixed relative collector mode bug:
   - I/O failed when disks is on two ports
   - system hang when hotplug disk
   - system hang when unplug disk during run IO
3. Unlock ap->lock within .lldd_execute_task for direct mode to
   improve performance
Signed-off-by: NXiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is support for Marvell 88SE9445/88SE9485 SAS/SATA HBA, which
is based on Marvell 88SE9480.
Signed-off-by: NXiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The SCSI ALUA handler currently fails to attach to devices
reporting an UNAVAILABLE/OFFLINE AAS. But given that an
UNAVAILABLE/OFFLINE AAS can transition to other states
like ACTIVE/OPTIMIZED, ACTIVE/NON-OPTIMIZED, etc. as per
SPC4, this ALUA handler behavior should be rectified so
as to attach to devices which also report an
UNAVAILABLE/OFFLINE AAS.
Signed-off-by: NMartin George <marting@netapp.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Adding support for inline data padding for TAPE drive when running U320.

[jejb: whitespace fixes]
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Remove debug print from mptscsih_qcmd function call.
This debug print cause flood of prints and difficult to debug other issues.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

FW may take more time cleaning up IOs issued to multiple targets.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Use MISC_DBG instead.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If the session is not ready yet, we ask the SCSI-ml to retry. However, if the
session is just uploaded, we should not retry, but instead call scsi_done to
fail the IO.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Prematurely decrementing the reference may lead to cmd_mgr becoming NULL with
the cmds are still active.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Creating and destroying fcoe interface in a tight loop leads to a system
deadlock with the following call traces:

Call Trace:
[<ffffffff814f4b3d>] schedule_timeout+0x1fd/0x2c0
[<ffffffff814f469f>] ? wait_for_common+0x4f/0x190
[<ffffffff814f469f>] ? wait_for_common+0x4f/0x190
[<ffffffff814f4737>] wait_for_common+0xe7/0x190
[<ffffffff81042fa0>] ? default_wake_function+0x0/0x20
[<ffffffff81082c2d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff814f48bd>] wait_for_completion+0x1d/0x20
[<ffffffff81066d90>] flush_workqueue+0x290/0x5f0
[<ffffffff81066b00>] ? flush_workqueue+0x0/0x5f0
[<ffffffff81067148>] destroy_workqueue+0x38/0x340
[<ffffffffa0260289>] fc_remove_host+0x1b9/0x1f0 [scsi_transport_fc]
[<ffffffffa02ed195>] bnx2fc_if_destroy+0xc5/0x1f0 [bnx2fc]
[<ffffffffa02ed33a>] bnx2fc_destroy+0x7a/0x100 [bnx2fc]
[<ffffffffa02c789b>] fcoe_transport_destroy+0x9b/0x1b0 [libfcoe]
[<ffffffff81069ec2>] param_attr_store+0x52/0x80
[<ffffffff81069976>] module_attr_store+0x26/0x30
[<ffffffff8119e726>] sysfs_write_file+0xe6/0x170
[<ffffffff81134710>] vfs_write+0xd0/0x1a0
[<ffffffff811348e4>] sys_write+0x54/0xa0
[<ffffffff81002e02>] system_call_fastpath+0x16/0x1b
Call Trace:
[<ffffffff81074865>] async_synchronize_cookie_domain+0x75/0x120
[<ffffffff8106caa0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff81074925>] async_synchronize_cookie+0x15/0x20
[<ffffffff8107494c>] async_synchronize_full+0x1c/0x40
[<ffffffffa0057466>] sd_remove+0x36/0xc0 [sd_mod]
[<ffffffff81358a75>] __device_release_driver+0x75/0xe0
[<ffffffff81358bef>] device_release_driver+0x2f/0x50
[<ffffffff81357aee>] bus_remove_device+0xbe/0x120
[<ffffffff813553ef>] device_del+0x12f/0x1e0
[<ffffffff8137454d>] __scsi_remove_device+0xbd/0xc0
[<ffffffff81374585>] scsi_remove_device+0x35/0x50
[<ffffffff813746a7>] __scsi_remove_target+0xe7/0x110
[<ffffffff81374730>] ? __remove_child+0x0/0x30
[<ffffffff81374753>] __remove_child+0x23/0x30
[<ffffffff81354a2c>] device_for_each_child+0x4c/0x80
[<ffffffff81374703>] scsi_remove_target+0x33/0x60
[<ffffffffa02622c6>] fc_starget_delete+0x26/0x30 [scsi_transport_fc]
[<ffffffffa026271a>] fc_rport_final_delete+0xaa/0x200 [scsi_transport_fc]
[<ffffffff8106585a>] process_one_work+0x1aa/0x540
[<ffffffff810657eb>] ? process_one_work+0x13b/0x540
[<ffffffffa0262670>] ? fc_rport_final_delete+0x0/0x200 [scsi_transport_fc]
[<ffffffff81067ac9>] worker_thread+0x179/0x410
[<ffffffff81067950>] ? worker_thread+0x0/0x410
[<ffffffff8106c546>] kthread+0xb6/0xc0
[<ffffffff8103879b>] ? finish_task_switch+0x4b/0xe0
[<ffffffff81003ca4>] kernel_thread_helper+0x4/0x10
[<ffffffff814f7994>] ? restore_args+0x0/0x30
[<ffffffff8106c490>] ? kthread+0x0/0xc0
[<ffffffff81003ca0>] ? kernel_thread_helper+0x0/0x10

fc_remove_host() waits for flushing the workqueue, but it is stuck at flushing
the first work. The first work doesnt complete, because it is waiting for async
layer to complete the IOs. The async layer cannot complete the IO as the
terminate_rport_io for the second work was not called, which will be called
only when the first work completes. Hence the deadlock.  To resolve this
deadlock, the workqueue allocation has been modified from
create_singlethread_workqueue() to alloc_workqueue().

In addition, fc_terminate_rport_io() should be called before the
scsi_flush_work() to avoid the similar deadlock as above.

scsi fc alloc queue. move terminate rport io before flush
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Update driver version to 8.3.22
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Fixed the mixed declarations and codes which violate ISO C90
   (declarations in subsections that assign at declaration)
- Add BSG data transfer size protection in mailbox command pass-through path
- Invoke BSG job_done while holding spinlock to fix deadlock
- Added support for checking SLI_CONFIG subcommands
- Fixed bug in BSG mailbox size check to non-embedded external buffer
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fixes related to new hardware

- Restrict driver to look at BAR2 or BAR4 only for if_type 0.
- Allow SLI4 with FCOE_MODE not set for new SLI4 FC adapters.
- Add Temporary RPI field to the ELS request WQE.
- Do not override CT field in issue_els_flogi for SLI4 IF type 2
- For RQ_CREATE_V2 mbx cmd: fill in the rqe_size and page_size for RQ_CREATE.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Miscellaneous fixes

- Do not limit RPI Count to a minimum of 64
- Fix FCFI incorrect on received unsolicited frames.
- Save the FCFI returned in the REG_FCFI mailbox command if it was successful.
- Fixed Vports not sending FDISC after lips.
- Align based on the SLI4_PAGE_SIZE.
- Fixed double byte swap on received RRQ.
- Fixed mask size for the wq_id mask from 0x7F to 0x7FFF.
- Clear FC_FABRIC flag when NPIV LOGO completes (and add a log message).
- Modified driver to skip round robin only when ulpStatus==LOCAL_REJECT
  and word4=SEQUENCE_TIMEOUT to prevent FLOGI to disconnected FCF.
- Don't add rport if driver unloading
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Debugfs enhancements

- Added iDiag support for new adapters.
- Added queue entry access methods.
- Fix host/port index in decimal
- Added Doorbell register access methods.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Move the initialization of debugfs before bfa init, to enable us to
collect driver/firmware traces if init fails.  Also add a printk to
display message on bfa_init failure.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch includes fixes for two issues releated to firmware download
implementation: 1) Merged memory leak fix provided by Jesper Juhl
<jj@chaosbits.net>. Basically we need to call release_firmware() after
request_firmware(). 2) fixed issues with the firmware download interface
as pointed out by Rolf Eike Beer <eike@sf-mail.de> in linux-scsi. Rearranged
the code and fixed related function protypes.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

During performance testing on P7 machines it was observed that the interrupt
service routine was doing unnecessary MMIO operations.

This patch rearranges the logic of the routine and moves some of the code out
of the main routine.  The result is that there are now fewer MMIO operations in
the performance path of the code.

As a result of the above change, an existing condition was exposed where the
driver could get an "unexpected" hrrq interrupt.  The original code would flag
the interrupt as unexpected and then reset the adapter.  After further analysis
it was confirmed that this condition can occasionally occur and that the
interrupt can safely be ignored.  Additional code in this patch detects this
condition, clears the interrupt and allows the driver to continue without
resetting the adapter.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Based on the operating modes, handler decides whether to send mode
select or not. Purpose here is to reduce io-shipping as much as
possible whenever there is an option.
Signed-off-by: NBabu Moger <babu.moger@lsi.com>
Reviewed-by: NYanling Qi <yanling.qi@lsi.com>
Reviewed-by: NSudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: NSomasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: NBob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: NVijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch detects different operating RDAC modes during the
discovery. It also collects the information about the preferred path.
Signed-off-by: NBabu Moger <babu.moger@lsi.com>
Reviewed-by: NYanling Qi <yanling.qi@lsi.com>
Reviewed-by: NSudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: NSomasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: NBob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: NVijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch adds definitions to support for different operating modes
for LSI rdac storage.  Currently, rdac support 3 operation modes.

1. RDAC mode(legacy)
2. AVT mode
3. IOSHIP mode

These definitions are used while activating the path(rdac_activate).
Signed-off-by: NBabu Moger <babu.moger@lsi.com>
Reviewed-by: NYanling Qi <yanling.qi@lsi.com>
Reviewed-by: NSudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: NSomasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: NBob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: NVijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch removes three volatile declarations based on some feedback and code
analysis.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch has Support for the new solid state device product SSS6200
from LSI and relavent features w.r.t SSS6200.

The major feature added in this driver is supporting Direct-I/O to the
SSS6200 storage.There are some additional changes done to avoid exposing
the RAID member disks to the OS and hiding/exposing drives based on the
OEM Specific Flag in Manufacturing Page10 (this is required to handle
specific changes in the SSS6200 firmware).

Each and every changes are listed below.
1. Hiding IR related messages.
For SSS6200, the driver is modified not to print IR related events.
Even if the debugging is enabled the IR related messages will not be displayed.
In some places if there is a need to display a message related to IR the
string "IR" is replaced with string "DD" and the string "volume" is replaced
with "direct drive". But the function names are not changed hence there are
some places where the reference to volume can be seen if debug level is set.

2. Removed RAID transport support
In Linux the user can retrieve RAID volume information from the sysfs directory.
This support is removed for SSS6200.

3. Direct I/O support.
The driver tries to enable direct I/O when a volume is reported to the driver
by the firmware through IRCC events and the driver does this just before
reporting to the OS, hence all the OS issued I/O can go through direct path
if they can, The first validation is to see whether the manufacturing page10
flag is set to expose all drives always. If that is set, the driver will not
enable direct I/O and displays the message "DDIO" is disabled globally as
drives are exposed. The driver checks whether there is more than one volume
in the controller, if so the direct I/O will be disabled globally for all
volumes in the controller and the message displayed will be "DDIO is disabled
globally as number of drives > 1.
If retrieving number of PD is failed the driver will not enable direct I/O
and displays the message Failure in computing number of drives DDIO disabled.
If memory allocation for RAIDVolumePage0 is failed, the driver will not enable
direct I/O and displays the message Memory allocation failure for
RVPG0 DDIO disabled.  If retrieving RAIDVolumePage0 is failed the driver will
not enable direct I/O and displays the message Failure in retrieving
RVPG0 DDIO disabled

If the number of PD in a volume is greater than 8, then the direct I/O will
be disabled.
If any of individual drives handle retrieval is failed then the DD-IO will
be disabled.
If the volume is not RAID0 or if the block size is not 512 then the DD-IO will
be disabled.
If the volume size is greater than 2TB then the DD-IO will be disabled.
If the driver is not able to find a valid stripe exponent using the configured
stripe size then the DD-IO will be disabled

When the DD-IO is enabled the driver will check every I/O request issued to
the storage and checks whether the request is either
READ6/WRITE6/READ10/WRITE10, if it is and if the complete I/O transfer
is within a stripe size then the I/O is redirected to
the drive directly instead of the volume.

On completion of every I/O, if the completion is failure means if the reply
is address reply with a reply frame associated with it, then the type of I/O
will be checked, if the I/O is direct then the I/O will be retried to
the volume once.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: NEric Moore <eric.moore@lsi.com>
Reviewed-by: NSathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The SCSI midlayer stops all command processing when in error handling, which
means there is no chance for command reuse when the abort handler is called.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The SCSI midlayer stops all command processing when in error handling, which
means there is no chance for command reuse when the abort handler is called.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: N"Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The isd200 sub-driver increments the command serial number despite not
using it at all in it's routine for sending internal scsi commands.
Remove the increment to prepare for removing the serial_number field.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Stop using cmd->serial_number in printks.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Currently fcoe interface cleanup is done after ndo_fcoe_disable
and that prevents logoff going out to the peer, so this patch
moves all netdev cleanup and its releasing inside
fcoe_interface_cleanup to have log off before ndo_fcoe_disable
disables the fcoe.

This patch also fixes asymmetric rtnl locking around fcoe_if_destroy,
as currently this function requires rtnl held by its caller
and then have this func drops the lock, instead now don't have
any processing under rtnl inside fcoe_if_destroy, this required
moving few func to get build working again.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added REC_TOV_CONST intent was to have rec tov as e_d_tov + 1s
but currently it is e_d_tov + 1ms since e_d_tov is stored in ms
unit.

Also returned rec tov by get_fsp_rec_tov is in ms and this ms tov
is used as-is with fc_fcp_timer_set expecting jiffies tov.

Fixed this by having get_fsp_rec_tov return rec tov in jiffies
as e_d_tov + 1s and then use jiffies tov w/ fc_fcp_timer_set.

Also some cleanup, no need to cache get_fsp_rec_tov return value
in local rec_tov at various places.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

As ema_list is already initialized by libfc_host_alloc.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

fix typo of '_attach' -> '_detach' in the comment.
Reported-by: NFrank Zhang <frank_1.zhang@intel.com>
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

possible buffer overflow in fcoe_transport_show when reaching the end of
buffer and crossing PAGE_SIZE boundary.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When rmmoving the underlying fcoe transport driver module by force when
it's attached and in use, the correspoding netdev mapping should be
cleaned up properly as well, otherwise the lookup for a given netdev
for the transport would still return non NULL pointer, causing "unable
to handle paging request" bug.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The host_lock is still used to protect the can_queue
value in the Scsi_Host, but it doesn't need to be held
and released by each caller. This patch moves the lock
usage into the fc_fcp_can_queue_ramp_up and
fc_fcp_can_queue_ramp_down routines.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>