提交 · e3230494b57ece68750e3e32d3e53d6b00917058 · openeuler / raspberrypi-kernel

29 11月, 2016 2 次提交

net: phy: realtek: fix enabling of the TX-delay for RTL8211F · e3230494

由 Martin Blumenstingl 提交于 11月 25, 2016

The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. There are dedicated phy-modes which tell the
PHY driver to enable the RX and/or TX delays:
- PHY_INTERFACE_MODE_RGMII should disable the RX and TX delay in the
  PHY (if required, the MAC should add the delays in this case)
- PHY_INTERFACE_MODE_RGMII_ID should enable RX and TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_TXID should enable the TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_RXID should enable the RX delay in the PHY
  (currently not supported by RTL8211F)

With this patch we enable the TX delay for PHY_INTERFACE_MODE_RGMII_ID
and PHY_INTERFACE_MODE_RGMII_TXID.
Additionally we now explicity disable the TX-delay, which seems to be
enabled automatically after a hard-reset of the PHY (by triggering it's
reset pin) to get a consistent state (as defined by the phy-mode).

This fixes a compatibility problem with some SoCs where the TX-delay was
also added by the MAC. With the TX-delay being applied twice the TX
clock was off and TX traffic was broken or very slow (<10Mbit/s) on
1000Mbit/s links.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e3230494

Documentation: devicetree: clarify usage of the RGMII phy-modes · e5f3a4a5

由 Martin Blumenstingl 提交于 11月 25, 2016

RGMII requires special RX and/or TX delays depending on the actual
hardware circuit/wiring. These delays can be added by the MAC, the PHY
or the designer of the circuit (the latter means that no delay has to
be added by PHY or MAC).
There are 4 RGMII phy-modes used describe where a delay should be
applied:
- rgmii: the RX and TX delays are either added by the MAC (where the
  exact delay is typically configurable, and can be turned off when no
  extra delay is needed) or not needed at all (because the hardware
  wiring adds the delay already). The PHY should neither add the RX nor
  TX delay in this case.
- rgmii-rxid: configures the PHY to enable the RX delay. The MAC should
  not add the RX delay in this case.
- rgmii-txid: configures the PHY to enable the TX delay. The MAC should
  not add the TX delay in this case.
- rgmii-id: combines rgmii-rxid and rgmii-txid and thus configures the
  PHY to enable the RX and TX delays. The MAC should neither add the RX
  nor TX delay in this case.

Document these cases in the ethernet.txt documentation to make it clear
when to use each mode.
If applied incorrectly one might end up with MAC and PHY both enabling
for example the TX delay, which breaks ethernet TX traffic on 1000Mbit/s
links.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e5f3a4a5

28 11月, 2016 12 次提交

net, sched: respect rcu grace period on cls destruction · d9363774

由 Daniel Borkmann 提交于 11月 27, 2016

Roi reported a crash in flower where tp->root was NULL in ->classify()
callbacks. Reason is that in ->destroy() tp->root is set to NULL via
RCU_INIT_POINTER(). It's problematic for some of the classifiers, because
this doesn't respect RCU grace period for them, and as a result, still
outstanding readers from tc_classify() will try to blindly dereference
a NULL tp->root.

The tp->root object is strictly private to the classifier implementation
and holds internal data the core such as tc_ctl_tfilter() doesn't know
about. Within some classifiers, such as cls_bpf, cls_basic, etc, tp->root
is only checked for NULL in ->get() callback, but nowhere else. This is
misleading and seemed to be copied from old classifier code that was not
cleaned up properly. For example, d3fa76ee ("[NET_SCHED]: cls_basic:
fix NULL pointer dereference") moved tp->root initialization into ->init()
routine, where before it was part of ->change(), so ->get() had to deal
with tp->root being NULL back then, so that was indeed a valid case, after
d3fa76ee, not really anymore. We used to set tp->root to NULL long
ago in ->destroy(), see 47a1a1d4 ("pkt_sched: remove unnecessary xchg()
in packet classifiers"); but the NULLifying was reintroduced with the
RCUification, but it's not correct for every classifier implementation.

In the cases that are fixed here with one exception of cls_cgroup, tp->root
object is allocated and initialized inside ->init() callback, which is always
performed at a point in time after we allocate a new tp, which means tp and
thus tp->root was not globally visible in the tp chain yet (see tc_ctl_tfilter()).
Also, on destruction tp->root is strictly kfree_rcu()'ed in ->destroy()
handler, same for the tp which is kfree_rcu()'ed right when we return
from ->destroy() in tcf_destroy(). This means, the head object's lifetime
for such classifiers is always tied to the tp lifetime. The RCU callback
invocation for the two kfree_rcu() could be out of order, but that's fine
since both are independent.

Dropping the RCU_INIT_POINTER(tp->root, NULL) for these classifiers here
means that 1) we don't need a useless NULL check in fast-path and, 2) that
outstanding readers of that tp in tc_classify() can still execute under
respect with RCU grace period as it is actually expected.

Things that haven't been touched here: cls_fw and cls_route. They each
handle tp->root being NULL in ->classify() path for historic reasons, so
their ->destroy() implementation can stay as is. If someone actually
cares, they could get cleaned up at some point to avoid the test in fast
path. cls_u32 doesn't set tp->root to NULL. For cls_rsvp, I just added a
!head should anyone actually be using/testing it, so it at least aligns with
cls_fw and cls_route. For cls_flower we additionally need to defer rhashtable
destruction (to a sleepable context) after RCU grace period as concurrent
readers might still access it. (Note that in this case we need to hold module
reference to keep work callback address intact, since we only wait on module
unload for all call_rcu()s to finish.)

This fixes one race to bring RCU grace period guarantees back. Next step
as worked on by Cong however is to fix 1e052be6 ("net_sched: destroy
proto tp when all filters are gone") to get the order of unlinking the tp
in tc_ctl_tfilter() for the RTM_DELTFILTER case right by moving
RCU_INIT_POINTER() before tcf_destroy() and let the notification for
removal be done through the prior ->delete() callback. Both are independant
issues. Once we have that right, we can then clean tp->root up for a number
of classifiers by not making them RCU pointers, which requires a new callback
(->uninit) that is triggered from tp's RCU callback, where we just kfree()
tp->root from there.

Fixes: 1f947bf1 ("net: sched: rcu'ify cls_bpf")
Fixes: 9888faef ("net: sched: cls_basic use RCU")
Fixes: 70da9f0b ("net: sched: cls_flow use RCU")
Fixes: 77b9900e ("tc: introduce Flower classifier")
Fixes: bf3994d2 ("net/sched: introduce Match-all classifier")
Fixes: 952313bd ("net: sched: cls_cgroup use RCU")
Reported-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Roi Dayan <roid@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

d9363774

tipc: fix link statistics counter errors · 95901122

由 Jon Paul Maloy 提交于 11月 25, 2016

In commit e4bf4f76 ("tipc: simplify packet sequence number
handling") we changed the internal representation of the packet
sequence number counters from u32 to u16, reflecting what is really
sent over the wire.

Since then some link statistics counters have been displaying incorrect
values, partially because the counters meant to be used as sequence
number snapshots are now used as direct counters, stored as u32, and
partially because some counter updates are just missing in the code.

In this commit we correct this in two ways. First, we base the
displayed packet sent/received values on direct counters instead
of as previously a calculated difference between current sequence
number and a snapshot. Second, we add the missing updates of the
counters.

This change is compatible with the current netlink API, and requires
no changes to the user space tools.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

95901122

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec · 8eb4adf6

由 David S. Miller 提交于 11月 27, 2016

Steffen Klassert says:

====================
pull request (net): ipsec 2016-11-25

1) Fix a refcount leak in vti6.
   From Nicolas Dichtel.

2) Fix a wrong if statement in xfrm_sk_policy_lookup.
   From Florian Westphal.

3) The flowcache watermarks are per cpu. Take this into
   account when comparing to the threshold where we
   refusing new allocations. From Miroslav Urbanek.

Please pull or let me know if there are problems.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

8eb4adf6

driver: macvtap: Unregister netdev rx_handler if macvtap_newlink fails · e824265d

由 Gao Feng 提交于 11月 25, 2016

The macvtap_newlink registers the netdev rx_handler firstly, but it
does not unregister the handler if macvlan_common_newlink failed.
Signed-off-by: NGao Feng <fgao@ikuai8.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e824265d

Merge branch 'more-phydev-leaks' · a1cad5ee

由 David S. Miller 提交于 11月 27, 2016

Johan Hovold says:

====================
net: fix phydev reference leaks

This series fixes a number of phydev reference leaks (and one of_node
leak) due to failure to put the reference taken by of_phy_find_device().

Note that I did not try to fix drivers/net/phy/xilinx_gmii2rgmii.c which
still leaks a reference.

Against net but should apply just as fine to net-next.

v2:
 - use put_device() instead of phy_dev_free() to put the references
   taken in net/dsa (patch 1/4).
 - add four new patches fixing similar leaks
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

a1cad5ee

net: qcom/emac: fix of_node and phydev leaks · 6ffe1c4c