The association in the decice tree between PCI and MSI
using fsl,msi property was an artificial one and it does
not reflect the actual hardware.
Signed-off-by: NDiana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add DTS file for a4m072 board and add its name to the list
of the supported boards.
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Grant Likely <grant.likely@secretlab.ca>
cc: devicetree-discuss@ozlabs.org
cc: Wolfgang Denk <wd@denx.de>
cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

This patch updates the dts file for bluestone board with support:
- UART1
- L2 cache
- NAND with NDFC
- PCI-E
Signed-off-by: NVinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The MSIIR register for each MSI bank is aliased to a different
address. The MSI node reg property was updated to contain this
address:

e.g. reg = <0x41600 0x200 0x44140 4>;

The first region contains the address and length of the MSI
register set and the second region contains the address of
the aliased MSIIR register at 0x44140.
Signed-off-by: NDiana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Create mpc8548cds_36b.dts. Support 36-bit mode.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Create mpc8548cds.dtsi
* Move lbc, soc and pci0 nodes to mpc8548cds_32b.dtsi
* Change cuImage.mpc8548cds to cuImage.mpc8548cds_32b
* Rename mpc8548cds.dts to mpc8548cds_32b.dts
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove FPGA(CADMUS) macros in code. Move it to dts.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Correct ethernet1 and add ethernet2 and ethernet3.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NZhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix the compatible string of sec 4.0 to match with CAAM driver according
to Documentation/devicetree/bindings/crypto/fsl-sec4.txt
Signed-off-by: NLiu Shuo <shuo.liu@freescale.com>
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The mpc836x_mds platform has been broken since the commit
6fe32649

  "netdev/phy: Use mdiobus_read() so that proper locks are taken"

which caused the fsl_pq_mdio TBI autoprobe to oops.  The oops
was "fixed" in commit 28d8ea2d

  "fsl_pq_mdio: Clean up tbi address configuration"

by simply removing the the autoscan code, and making tbi nodes
mandatory.  Some of the newer reference platforms were updated
to have tbi nodes in 22066949

  "powerpc: Add TBI PHY node to first MDIO bus"

but the older mpc836x didn't get one and hence was just failing
with -EBUSY as follows:

 fsl-pq_mdio: probe of e0102120.mdio failed with error -16
   ...
 net eth0: Could not attach to PHY
 eth0: Cannot initialize PHY, aborting.

Add a TBI node and use the 1st free address for it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: NMartyn Welch <martyn.welch@ge.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus

PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot

10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021

USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot

Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NZhicheng Fan <b32736@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJin Qing <b24347@freescale.com>
Signed-off-by: NJia Hongtao <B38951@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.

Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NOR flash, need to be disabled.

This also means that the localbus is not a 'simple-bus' any more, so remove
that string from the compatible node.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Create a 32-bit address space version of p1022ds.dts.  To avoid confusion,
p1022ds.dts is renamed to p1022ds_36b.dts.  We also create p1022ds.dtsi
to store some common nodes.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The properties indicates that the hardware supports waking up via magic
packet.
Signed-off-by: NXie Xiaobo <X.Xie@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add partitions for NOR and NAND Flash.
Signed-off-by: NXie Xiaobo <X.Xie@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Fix typo introduced by "powerpc: Add TBI PHY node to first MDIO bus"
from Andy Fleming.
It's device_type rather than device-type, which causes the mdio probe to
fail thus making all gianfar ethernet interfaces unusable.
Signed-off-by: NGustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This is here most likely since the FSL bsp. Back in the FSL bsp it was
set to 50Mhz and working. However the driver divided the SoC freq. only
by 2. According to the TRM the platform clock (which the manual refers
in its formula) is the system clock divided by two. So in the end it has
to divide by 4 and this is what the fsl-spi driver in tree is doing.
Since then the flash is not wokring I guess. After chaning the freq from
50Mhz to 40Mhz like others do then I can access the flash.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

It is not at 0xffa00000. According to current u-boot source the NAND
controller is always at 0xff800000 and it is either at CS0 or CS1
depending on NAND or NAND+NOR mode. In 36bit mode it is shifted to
0xfff800000 but it has always an eight there and never an A.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus

PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot

10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021

USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot

Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NZhicheng Fan <b32736@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add usb controller version info for the following:
MPC8536, P1010, P1020, P1021, P1022, P1023, P2020, P2041,
P3041, P3060, P5020
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NTang Yuantian <b29983@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
    - x1 PCIe slot or x1 PCIe to dual SATA controller
    - x1 mini-PCIe slot
USB 2.0
    - ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic’s GL850A
    - Two USB2.0 Type A receptacles
    - One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NMatthew McClintock <msm@freescale.com>
Signed-off-by: NXu Jiucheng <B37781@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This compatible value will be used to distinguish some special features of APM821XX EMAC: no half duplex mode support, configuring jumbo frame.
Signed-off-by: NDuc Dang <dhdang@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FreeScale PowerQUICC-III-compatible (mpc85xx/mpc86xx) MPICs do not
correctly report the number of hardware interrupt sources, so software
needs to override the detected value with "256".

To avoid needing to write custom board-specific code to detect that
scenario, allow it to be easily overridden in the device-tree.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The Freescale MPIC (and perhaps others in the future) is incapable of
routing non-IPI interrupts to more than once CPU at a time.  Currently
all of the Freescale boards msut pass the MPIC_SINGLE_DEST_CPU flag to
mpic_alloc(), but that information should really be present in the
device-tree.

Older board code can't rely on the device-tree having the property set,
but newer platforms won't need it manually specified in the code.

[BenH: Remove unrelated changes, folded in a different patch]
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The MPIC code checks for a "big-endian" property and sets the flag
MPIC_BIG_ENDIAN if one is present, although prior to the "mpic->flags"
fixup that would never have worked anways.

Unfortunately, even now that it works properly, the Freescale mpic
device-node (the "PowerQUICC-III"-compatible one) does not specify it,
so all of the board ports need to manually pass it to mpic_alloc().

Document the flag and add it to the pq3 device tree.  Existing code will
still need to pass the MPIC_BIG_ENDIAN flag because their dtb may not
have this property, but new platforms shouldn't need to do so.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Add usb2 controller node for P1020RDB, P2020RDB, P2020DS, P1021MDS
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable USB2 controller node for P1020RDB. USB2 controller is used only
when board boots from SPI or SD as it is muxed with eLBC
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

According to latest kernel, the auto-cmd12 property should be
"sdhci,auto-cmd12", and according to the SDHC binding and the workaround for
the special chip, add the chip compatible for eSDHC: "fsl,p1022-esdhc",
"fsl,mpc8536-esdhc", "fsl,p1020-esdhc", "fsl,p2020-esdhc" and
"fsl,p1010-esdhc".
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features.  Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

PCI ranges, localbus reg and localbus chip-select 2 range do not match
the memory map setup by bootloader.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.

The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Based on original work by David 'Shaggy' Kleikamp.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.

This adds it using ppc40x_simple and provides a device-tree.

There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.

The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>