Move rt2x00rfkill_register(rt2x00dev) to rt2x00lib_probe_dev
  function. It fixes of starting rfkill_poll function at the
  right time if sets hard rfkill block and reboot. rt2x00mac_rfkill_poll
  should be starting before bringing up the wireless interface.
Signed-off-by: NChen, Chien-Chia <machen@suse.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
CC: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The following is seen during allmodconfig builds for MIPS:

drivers/bcma/driver_pci_host.c:518:2: error: implicit declaration
of function 'pcibios_enable_device' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/bcma/driver_pci_host.o] Error 1

Most likey introduced by commit 49dc9577

    "bcma: add PCIe host controller"

Add the header instead of implicitly assuming it will be present.
Sounds like a good idea, but that alone doesn't fix anything.

The real problem is that the Kconfig has settings related to whether
PCI is possible, i.e.

  config BCMA_HOST_PCI_POSSIBLE
        bool
        depends on BCMA && PCI = y
        default y

  config BCMA_HOST_PCI
        bool "Support for BCMA on PCI-host bus"
        depends on BCMA_HOST_PCI_POSSIBLE

...but what is missing is that BCMA_DRIVER_PCI_HOSTMODE doesn't
have any dependencies on the above.  Add one.

CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the rate-control indexing is incorrectly set up, mac80211 issues
a warning and returns NULL from the call to ieee80211_get_tx_rate().
When this happens, avoid a NULL pointer dereference.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before the switch to asynchronous firmware loading (mainline commit b0302aba),
it was necessary to load firmware when initializing the first of the units
in a dual-mac system. After the change, it is necessary to load firmware in
both units.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.

To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DA9052/53 PMIC has capability to supply power for upto 3 banks of 6
white serial LEDS.  It can also control intensity of independent banks
and to drive these banks boost converter will provide up to 24V and
forward current of max 50mA.

This patch allows to control intensity of the individual WLEDs bank
through DA9052/53 PMIC.

This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op.  This leads to a
proliferation of the default_open() implementation across the entire
tree.

Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().

This replacement was done with the following semantic patch:

<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}

@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to 88pm860x spec, rtc alarm irq enable control is bit3 for
RTC_ALARM_EN, so fix it.
Signed-off-by: NJett.Zhou <jtzhou@marvell.com>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change send_sig_all() to use do_send_sig_info(SEND_SIG_FORCED) instead
of force_sig(SIGKILL).  With the recent changes we do not need force_ to
kill the CLONE_NEWPID tasks.

And this is more correct.  force_sig() can race with the exiting thread,
while do_send_sig_info(group => true) kill the whole process.

Some more notes from Oleg Nesterov:

> Just one note. This change makes no difference for sysrq_handle_kill().
> But it obviously changes the behaviour sysrq_handle_term(). I think
> this is fine, if you want to really kill the task which blocks/ignores
> SIGTERM you can use sysrq_handle_kill().
>
> Even ignoring the reasons why force_sig() is simply wrong here,
> force_sig(SIGTERM) looks strange. The task won't be killed if it has
> a handler, but SIG_IGN can't help. However if it has the handler
> but blocks SIGTERM temporary (this is very common) it will be killed.

Also,

> force_sig() can't kill the process if the main thread has already
> exited. IOW, it is trivial to create the process which can't be
> killed by sysrq.

So, this patch fixes the issue.
Suggested-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The driver uses a 2-order allocation, which is too much on architectures
like ppc64, which has a 64KiB page. This particular allocation is used
for large packet fragments that may have a size of 512, 1024, 4096 or
fill the whole allocation. So, a minimum size of 16384 is good enough
and will be the same size that is used in architectures of 4KiB sized
pages.

This will avoid allocation failures that we see when the system is under
stress, but still has plenty of memory, like the one below.

This will also allow us to set the interface MTU to higher values like
9000, which was not possible on ppc64 without this patch.

Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB
83137 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap  = 10420096kB
Total swap = 10420096kB
107776 pages RAM
1184 pages reserved
147343 pages shared
28152 pages non-shared
netstat: page allocation failure. order:2, mode:0x4020
Call Trace:
[c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable)
[c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930
[c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170
[c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en]
[c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en]
[c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en]
[c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en]
[c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450
[c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290
[c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24
[c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110
[c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0
[c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Tested-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit (bfab27a1 stmmac: add the experimental PCI support) the
IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup()
function. This patch re-adds the flag.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch clears a warning message of "MDC/MDIO access timeout" which may
appear when interface is loaded due to missing clock setting before resetting
the LED, and starting periodic function too early.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a link problem on the second port of BCM57711 + BCM84823 boards due to
incorrect macro usage.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by
removing a logic error checking for a different PHY.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better
link strength.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 57810-KR flow-control handling link is achieved via CL37 AN.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modified from original patch from Chris.

The sky2 driver has to have 8 byte alignment of receive buffer
on some chip versions. On architectures which don't support efficient
unaligned access this doesn't work very well. The solution is to
just copy all received packets which is what the driver already
does for small packets.

This allows the driver to be used on the Tilera TILEmpower-Gx, since
the tile architecture doesn't currently handle kernel unaligned accesses,
just userspace.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.

Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 7d26bb10 "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Tegra30 support was added to the Tegra GPIO driver, a few places
which iterated over all banks were not converted to use the variable
tegra_gpio_bank_count rather than hard-coding the bank count. Fix this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

Tegra20 and Tegra30 share the same register layout within registers, but
the addresses of the registers is a little different. Fix the driver to
cope with this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>

This fixes the CPUFREQ dependency for regarding EXYNOS SoCs
such as EXYNOS4210, EXYNOS4X12 and EXYNOS5250. Its cpufreq
driver should be built with selection of SoC arch part.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Compilation error in case of non-DT configuration without this
of.h header file.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

Change number of ports to 3 for newer SoCs. Modify pdata structure
and ohci-at91 code that was dealing with ports information and check
of port indexes.
Several coding style errors have been addresses as the patch was touching
affected lines of code and was producing errors while run through
checkpatch.pl.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

The DT information are filled in a pdata structure and then passed on
to the usual check code of the probe function. Thus we do not need to
redo the gpio checking and irq configuration in the DT-related code.
On the other hand, we setup GPIO direction in driver for vbus and
overcurrent. It will be useful when moving to pinctrl subsystem.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>

The information is not properly taken into account
for {get|set}_power() functions.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>		[3.2+]

This reverts commit d06221c0.

It turns out to trigger the "BUG_ON(!PageCompound(page))" in kfree(),
apparently because the code ends up trying to free somethng that was
never kmalloced in the first place.

BenH points out that the patch was untested and wasn't meant to go into
the upstream kernel that quickly in the first place.

Backtrace:
  bios_shadow
  bios_shadow_prom
  nv_mask
  init_io
  bios_shadow
  nouveau_bios_init
  NVReadVgaCrtc
  NVSetOwner
  nouveau_card_init
  nouveau_load
Reported-by: NMeelis Roos <mroos@linux.ee>
Requested-by: NDave Airlie <airlied@gmail.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

MCA details seldom change inbetween the models of a family so don't
be too conservative and enable decoding on everything starting from
K8 onwards. Minor adjustments can come in later but most importantly,
we have some decoding infrastructure in place for upcoming models by
default.
Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>

The keyboard on my SUN SPARCstation 5 no longer worked.

    The culprint was: d4e33fac
    ("serial: Kill off NO_IRQ")

Fix up logic for no irq / irq so the keyboard works again.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver was recently moved from IIO (where it worked) to hwmon (where
it doesn't.) This breakage occured because the hwmon version neglected to
correctly initialize a reference to spi_dev in its drvdata. The result is a
segfault every time the temperature is queried.
Signed-off-by: NGraeme Smecher <gsmecher@threespeedlogic.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

NAPI is disabled during suspend and needs to be enabled on resume. Without
this the driver locks up during resume in rtl_reset_work() trying to disable
NAPI again.
Signed-off-by: NArtem Savkov <artem.savkov@gmail.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 621b4d66 updated the bnx2x driver to a new FW version, but lacked
a commit to a header file with changes to the firmware's interface.
The missing interface change causes iscsi and fcoe to misbehave with the
updated firmware.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.

This patch also fixes the return value of ip101a_config_init.

Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>