At least on my i830M here it reliably results in hard system hangs
nowadays. This is much worse than falling back to software rendering,
so I think we should simply rip this out.

After all we don't have any gpu reset for gen3 either, and there are a
lot more of those still around.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In truly crazy circumstances shmem might give us the wrong type of
page. So be a bit paranoid and double check this.

Reviewer: Damien Lespiau <damien.lespiau@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
References: http://lkml.org/lkml/2011/7/11/238Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The PIPEA quirk is specifically for the issue with the PIPEB PLL on
830gm being slaved to the PIPEA PLL, and so to use PIPEB requires PIPEA
running. i845 doesn't even have the second PLL or pipe, and enabling
the quirk results in a blank DVO LVDS.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The policy's max frequency is not equal to the CPU's max frequency. The
ring frequency is derived from the CPU frequency, and not the policy
frequency.

One example of how this may differ through sysfs. If the sysfs max
frequency is modified, that will be used for the max ring frequency
calculation.
(/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq). As far as I
know, no current governor uses anything but max as the default, but in
theory, they could. Similarly distributions might set policy as part of
their init process.

It's ideal to use the real frequency because when we're currently scaled
up on the GPU. In this case we likely want to race to idle, and using a
less than max ring frequency is non-optimal for this situation.

AFAIK, this patch should have no impact on a majority of people.

This behavior hasn't been changed since it was first introduced:
commit 23b2f8bb
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Tue Jun 28 13:04:16 2011 -0700

    drm/i915: load a ring frequency scaling table v3

CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Flush the primary plane changes when enabling/disabling the primary
plane in response to sprite visibility.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The new names make it clearer which plane we're talking about.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Resolve small conflict with the haswell_crtc_disable_planes
extraction.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The intel_flush_primary_plane name actually tells us which plane
we're talking about.

Also reorganize the internals a bit and add a missing POSTING_READ()
to make sure the hardware has seen the changes by the time we
return from the function.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

IPS should be OK as long as one plane is enabled on the pipe, but
it does seem to cause problems when going between primary only and
sprite only.

This needs more investigations, but for now just disable IPS whenever
the primary plane is disabled.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Disable fbc before disabling the primary plane, and enable fbc after
the primary plane has been enabled again.

Also use intel_disable_fbc() to disable FBC to avoid the pointless
overhead of intel_update_fbc(), and especially avoid having to clean
up and set up the stolen mem compressed buffer again.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the setplane operation fails, we shouldn't save the user's requested
plane coordinates. Since we adjust the coordinates during the clipping
process, make a copy of the originals, and once the operation has
succeeded save them for later reuse when the plane gets re-enabled.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move the variable initialization to where the variables are declared,
and kill a pointless to_intel_crtc() cast when we already have the
casted pointer.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's not use goto when a simple if suffices. This is not error handling
code or anything, so the goto looks out of place.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We used to call the entire intel specific update_plane hook while
holding struct_mutex. Actually we only need to hold struct_mutex while
pinning/unpinning the obj. The plane state itself is protected by the
kms locks, and as the object is pinned we can dig out the offset and
tiling information from it without fearing that it would change
underneath us.

So now we don't need to drop and reacquire the lock around the
wait_for_vblank. Also we will need another wait_for_vblank in the IVB
specific update_plane hook, and this way we don't need to worry about
struct_mutex there either.

Also move the intel_plane->obj=NULL assignment outside strut_mutex in
disable_plane to make it clear that it's not protected by struct_mutex.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We allow cursors to be set up when the pipe is disabled. Do the same for
sprites as well.

We need to be somewhat careful with the primary disable logic as we
don't want to accidentally enable the primary plane on a disabled pipe.

v2: Skip primary enable/disable and plane registers
    writes on disabled pipe
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the primary gets marked as disabled while the pipe is off for
instance, we should still re-enable it when the pipe is turned on,
unless the sprite covers it fully also in that configuration.
Unfortunately we do the plane visibility checks only in the sprite code,
which is executed after the primary enabling when turning the pipe off.

Ideally we should compute the plane visibility before touching the
hardware at all, but for now just set the primary_disabld flag
in intel_{enable,disable}_plane.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If channel equalization succeeds, there's no indication something went
wrong in clock recovery (unless debug is enabled). We should shout about
the failures and fix them instead of hiding them under the carpet.

This has allowed bugs like [1] stay dormant for a long time.

[1] https://bugs.freedesktop.org/show_bug.cgi?id=70117Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The VGACNTRL register contains a bunch of other stuff besides
the VGA_DISP_DISABLE bit. When we write the register we always set those
other bits to zero, so normally the current check would work.

However on HSW disabling and re-enabling the power well will reset the
VGACNTRL register to its default value, which has several of the other
bits set as well.

So only look at the VGA_DISP_DISABLE bit when checking whether the VGA
plane needs re-disabling.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Everyone else uses intel_PLL_is_valid(), so make VLV use it as well.

We don't have any special p and m limits on VLV, so skip those tests,
and we also need to skip the m1<=m2 test line PNV.

Reorganize the function a bit to move the n check alongside the rest of
the test for the non-derived dividers, and check the derived values
afterwards.

Note that this changes vlv_find_best_dpll() in two ways:
- The .vco comparison is now >max instead of >=max, and since we round
  down when calculating that stuff, we may now allow frequencies slightly
  above the max as we do on other platforms. The previous method
  disallowed exactly max and anything above it.
- We now check the .dot frequency against the data rate limits, which we
  didn't do before.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If vlv_find_best_dpll() couldn't find suitable PLL settings,
just say so instead of lying to caller.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

After aligning the p1 divider limits, and removing the unused p and m
limits, intel_limits_vlv_dac and intel_limits_vlv_hdmi are identical.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We don't use .dot_limit for anything on VLV, so don't populate it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We never check the p and m limits (which according to comments are
based on someone's guesswork), so just remove them.

VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm has no p and m
limits listed.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm tells us that the
minimum p2 divider is 2. Use that limit on the code.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm p1
can be 2-3 always.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For some reason there's a sort of off by one issue with the p1 divider.
The actual p1 limits according to
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm is 2-3, so we should
just say that instead of saying 1-3 and avoiding the 1 via the choice of
comparison operator.

I don't know why we're using different p1 limits for intel_limits_vlv_dac
and intel_limits_vlv_hdmi, but let's preserve that for now.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We limit the maximum n divider value in order to make sure the PLL's
reference inout is at least 19.2 MHz. I assume that is done to satisfy
some hardware requirement.

However we never check whether that calculated limit is below the
maximum supoorted N divider value (7). In practice that is always true
since we only support 100 MHz reference clock, but making the code
safe against higher reference clocks seems like a reasoanble thing to
do.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The p2 divider on VLV needs to be even when it's > 10. The current code
to make that happen is rather weird. Just make the step size adjustement
in the for loop decrement step.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rewrite vlv_find_best_dpll() to use intel_clock_t rather than
an army of local variables.

Also extract the code to calculate the derived values into
vlv_clock().

v2: Split up the earlier fixes, extract vlv_clock()
v3: Initialize best_clock
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We do 'bestppm - 10' in vlv_find_best_dpll() but never check whether
that might underflow. Add such a check.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use div_u64() to make the ppm calculation in vlv_find_best_dpll() safe
against interger overflows.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The interface uses an unsigned long, and we can use the unsigned counter
throughout our code, so do so. In the process, we notice one instance
where the shrink count is based on a heuristic rather than the result,
and another where we ask for too many pages to be purged.

v2: nr_to_scan needs to be promoted to a long as well, so just use
    sc->nr_to_scan directly.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since we are waiting upon IO completion, inform the kernel through use
of the io_schedule() call rather than the regular schedule(). This
should allow the kernel to make better decisions regarding scheduling
and power management.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.

i915_dma.c is just adjacent lines changed, nothing nefarious there.

Conflicts:
	drivers/gpu/drm/i915/i915_dma.c
	drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The user of these counters was killed in

 commit d79cdc83
 Author: Daniel Vetter <daniel.vetter@ffwll.ch>
 Date:   Thu Aug 8 15:41:32 2013 +0200

    drm: no-op out GET_STATS ioctl

so clean up the leftovers as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>