Flush the macvlan filters on VF reset to avoid conflict with other VFs that
may end up using the same MAC address.

The main change here is the call to ixgbe_set_vf_macvlan() with index 0.

Moved ixgbe_set_vf_macvlan() in front of ixgbe_vf_reset_event() to avoid
adding a prototype.
Reported-by: NSritej Kanakadandi Sritej Rama <skanakad@cisco.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid setting adapter->num_vfs early in the init code path when
using the max_vfs module parameter by passing it to ixgbe_enable_sriov()
as a function parameter.

This fixes an issue where if we failed to allocate vfinfo in
__ixgbe_enable_sriov() the driver will crash with NULL pointer in
ixgbe_disable_sriov() when attempting to free the vfinfo struct based
on adapter->num_vfs. Also it cleans up the assignment of adapter->num_vfs
since now it will only be set in __ixgbe_enable_sriov() and cleared in
ixgbe_disable_sriov().
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we exit at the end of the block, we can save a level of
indentation by performing an early return, and make the next several
sections of code more legible, with fewer 80 character line breaks.

Also moved allocating vfinfo at the beginning and the notification
for enabling SRIOV at the end of the function when we know that it
will succeed.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the code allocating memory for list of MAC addresses that
the VFs can use for MACVLAN into its own function.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When DCB is enabled, add checks to ensure creation of number of VF's is
valid based on the traffic classes configured by the device.
Signed-off-by: NUsha Ketineni <usha.k.ketineni@intel.com>
Tested-by: NRonald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch extends the xcast mailbox message to include support for
unicast promiscuous mode.  To allow a VF to enter this mode the PF
must be in promiscuous mode.

A later patch will add the support needed in the VF driver (ixgbevf)
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are two methods for setting mac addresses in a Macvlan, that
differentiate themselves in the function macvlan_set_mac_Address.
If the macvlan mode is passthru, then we use the dev_set_mac_address
method, otherwise we use the dev_uc api via macvlan_sync_addresses.
The latter method (which would stem from using any non-passthru mode,
like bridge, or vepa), calls down into the driver in a path that terminates
in ixgbevf_set_uc_addr_vf, which sends a IXGBE_VF_SET_MACVLAN message,
which causes the pf to spawn the noted error message.  This occurs because
it appears that the guest is trying to delete the mac address of the macvlan
before adding another.

The other path in macvlan_set_mac_address uses dev_set_mac_address, which
calls into ixgbevf_set_mac which uses the IXGBE_VF_SET_MAC_ADDR to the
pf to set the macvlan mac address.

The discrepancy here is in the handlers.  The handler function for
IXGBE_VF_SET_MAC_ADDR (ixgbe_set_vf_mac_addr) has a check for
the vfinfo[].trusted bit to allow the operation if the vf is trusted.
In comparison, the IXGBE_VF_SET_MACVLAN message handler
(ixgbe_set_vf_macvlan_msg) has no such check of the trusted bit.
Signed-off-by: NKen Cox <jkc@redhat.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.

For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.

Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
  Set vf vlan protocol 802.1ad:
    ip link set eth0 vf 1 vlan 100 proto 802.1ad
  Set vf to VST (802.1Q) mode:
    ip link set eth0 vf 1 vlan 100 proto 802.1Q
  Or by omitting the new parameter
    ip link set eth0 vf 1 vlan 100
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling SRIOV while the ixgbevf driver is loaded will result in all
mailbox requests from ixgbevf_open() being rejected by ixgbe because
adapter->clear_to_send is set to false on reset.

Call ixgbe_sriov_reinit() before pci_enable_sriov() to make sure that
mailbox requests are handled from the time ixgbevf is loaded.
Reported-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting spoofing, both VLAN and MAC need to be set together.
This change resolves an issue where MAC-VLANs on the VF fail to pass
traffic due to spoofed packets.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several areas of ixgbe were written before widespread usage of the
BIT(n) macro. With the impending release of GCC 6 and its associated new
warnings, some usages such as (1 << 31) have been noted within the ixgbe
driver source. Fix these wholesale and prevent future issues by simply
using BIT macro instead of hand coded bit shifts.

Also fix a few shifts that are shifting values into place by using the
'u' prefix to indicate unsigned. It doesn't strictly matter in these
cases because we're not shifting by too large a value, but these are all
unsigned values and should be indicated as such.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously the PF driver would only set VLAN spoof checking if
the VF had created VLANs. This was done by setting and checking
a counter (vlan_count) whenever a VLAN was created by the VF.
However it is possible for the vlan_count to be !=0 while there are
no VLANs assigned to the VF due to the count incrementing every
time a VLAN 0 is added on ifdown/up, which resulted in VLAN spoofing
always being set for those VFs.

This patch cleans up the logic by unconditionally setting VLAN based on
how the VF is configured (via ip link set ethX vf Y spoofchk on/off).
This change also resolves an issue where the VLAN spoofing can remain
set even after being disabled by the user due to the driver enabling
VLAN spoof checking every time a VLAN is added to the VF, but would
only allow changes in the setting if vlan_count != 0.

Also default_vf_vlan_id and vlans_enabled were removed from the
vf_data_storage structure since they are not being used in the driver.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Consolidate the logic behind configuring spoof checking:

Move the setting of the MAC, VLAN and Ethertype spoof checking into
ixgbe_ndo_set_vf_spoofchk().

Change ixgbe_set_mac_anti_spoofing() to set MAC spoofing per VF similar
to the VLAN and Ethertype functions - this allows us to call the helper
functions in ixgbe_ndo_set_vf_spoofchk() for all spoof check types and
only disable MAC spoof checking when creating MACVLAN.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit adds a callback which allows to adjust the maximum transmit
bitrate the card can output. This makes it possible to get a smooth
traffic instead of the default burst-y behaviour when trying to output
e.g. a video stream.

Much of the logic needed to get a correct bcnrc_val was taken from the
ixgbe_set_vf_rate_limit() function.
Signed-off-by: NRostislav Pehlivanov <atomnuker@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While doing the work on igb I realized there were a few cases where we were
still adding VLANs to the VLVF entries for the PF when they were not
needed.  This patch cleans that up so that the only time we add a PF entry
to the VLVF is either for VLAN 0 or if the PF has requested a VLAN that a VF
is already using.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When running certain routing protocols like VRRP, VF guests need the
ability to set the unicast address of the interface.  Extend the new ndo
trust feature to let the hypervisor trust a guest to set/update its own
unicast address.
Signed-off-by: NChas Williams <3chas3@gmail.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When I had rewritten the code for ixgbe_clear_vf_vlans() it looks like I
had transitioned back and forth between using word as an offset and using
word as a register offset.  As a result I honestly don't see how the code
was working before other than the fact that resetting the VLANs on the VF
like didn't do much to clear them.

Another issue found is that the mask was using a divide instead of a
modulus.  As a result the mask bit was incorrectly being set to either bit
0 or 1 based on the value of the VF being tested.  As a result the wrong
VFs were having their VLANs cleared if they were enabled.

I have updated the code so that word represents the offset in the array.
This way we can use the modulus and xor operations and they will make sense
instead of being performed on a 4 byte aligned value.

I replaced the statement "(word % 2) ^ 1" with "~word % 2" in order to
reduce the line length as the line exceeded 80 characters with the register
name inserted.  The two should be equivalent so the change should be safe.
Reported-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch guarantees that the VFs do not have access to VLANs that they
were not supposed to.  What this patch does is add code so that we delete
the previous port VLAN after adding a new one, and if we reset the VF we
clear all of the filters associated with it.

Previously the code was leaving all previous VLANs mapped to the VF and
they didn't get deleted unless the VF specifically requested it or if the
PF itself was reset.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry.  What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN.  The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The code for checking the PF bit in ixgbe_set_vf_vlan_msg was using the
wrong offset and as a result it was pulling the VLAN off of the PF even if
there were VFs numbered greater than 40 that still had the VLAN enabled.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Save VF device pointers and take references to speed accesses used
to monitor the device behavior to avoid slot resets. The saved
information avoids lock contention during the search used to access
each of the VFs.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NDarin Miller <darin.j.miller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The limitation of the number of multicast address for VF is not enough
for the large scale server with SR-IOV feature. IPv6 requires the multicast
MAC address for each IP address to handle the Neighbor Solicitation
message. We couldn't assign over 30 IPv6 addresses to a single VF.

This patch introduces the new mailbox API, IXGBE_VF_UPDATE_XCAST_MODE,
to update multicast mode of VF. This adds 3 modes;
  - NONE     only L2 exact match addresses or Flow Director enabled
  - MULTI    BAM and ROMPE set
  - ALLMULTI BAM, ROMPE and MPE set

If a guest VF user wants over 30 MAC multicast addresses, set IFF_ALLMULTI
to request PF to update xcast mode to enable VF multicast promiscuous mode.

On the other hand, enabling VF multicast promiscuous mode may affect
security and performance in the network of the NIC. Only trusted VF can
enable multicast promiscuous mode. The behavior of untrusted VF is the
same as previous version.
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implements the new netdev op to trust VF in ixgbe.

The administrator can turn on and off VF trusted by ip command which
supports trust message.
 # ip link set dev eth0 vf 1 trust on
or
 # ip link set dev eth0 vf 1 trust off

Send a ping to reset VF on changing the status of trusting.
VF driver will reconfigure its features on reset.
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For 82599 and x540 VFs and PF share the same RSS Key. Therefore we will
return the same RSS key for all VFs.

Support for other devices will be added later.
Signed-off-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add this new command for 82599 and x540 devices only. Support for other
devices will be added later.

82599 and x540 VFs and PF share the same RSS redirection table (RETA).
Therefore we just return it for all VFs.

For 82599 and x540 RETA table is an array of 32 registers (128 bytes) and
the maximum number of registers that may be delivered in a single VF-PF
channel command is 15. On the other hand VFs of these devices can be
configured to have up to 4 RSS queues. Therefore we will "compress" the
RETA by transferring only 2 bits per entry and thereby it will take only 8
registers (DWORDS) to transfer the whole VF RETA.

Thus this patch does the following:

  - Adds a new API version (to specify a new commands set).
  - Adds the IXGBE_VF_GET_RETA command to the VF-PF commands set.
Signed-off-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implements the new netdev op to allow user to enable/disable the ability
of a specific VF to query its RSS Indirection Table and an RSS Hash Key.

This patch limits the new feature support to 82599 and x540 devices only.
Support for other devices will be added later.
Signed-off-by: NVlad Zolotarov <vladz@cloudius-systems.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are currently storing our BRIDGE_MODE as a bit in our adapter flags.
This patch will store the actual mode instead which minimizes obfuscation
and makes following patches for X550 simpler.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.

$ git ls-files drivers/net/ethernet/ | \
  while read file ; do \
    codespell -w $file; \
  done

I removed a false positive in e1000_hw.h
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes couple of issues introduced by
commit 2b509c0c ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan")

- fix setting of the VLAN inside ixgbe_enable_port_vlan()
- disable the "hide VLAN" bit in PFQDE when port VLAN is disabled
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_set_sriov_queues() has the logic to allow multiple queues, this patch
just removes the limitation.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The new X550 family of MAC's will have a larger RSS hash (16 -> 64).
It will also support individual VF to have their own independent RSS
hash key.  This patch will enable this functionality
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch will add in the new MAC defines and fit it into the switch
cases throughout the driver.  New functionality and enablement support will
be added in following patches.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move setting of drop enable to support function.  This not only makes the
code more readable but is also prep for following patches that add
additional MAC support.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up functionality in ixgbe_ndo_set_vf_vlan that will simplify later
patches.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().

The following patch is all we need to protect against this panic:

ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]
Reported-by: NThierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NThierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Hardware has a limited number of pools available (64). Previously, no
checks were in place to limit the number of accelerated macvlan devices
based on the number of pools. Normally this would be ok, because there
was already a limit for these well below the number of available pools.
However, SR-IOV uses the very same pools. Therefor, we need to ensure
that the total number of pools (number of VFs plus the number of non-VF
pools in use for accelerated macvlans) does not exceed the number of
pools available in hardware.

This patch resolves a kernel NULL pointer dereference caused by the following commands:

$modprobe ixgbe max_vfs=63

$ethtool -K eth2 l2-fwd-offload on

$ip link add link eth2 macvlan0 type macvlan

$ip link set dev macvlan0 up

[  992.950080] BUG: unable to handle kernel NULL pointer dereference at 0000000000000056
[  992.951109] IP: [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.951684] PGD 22a80e067 PUD 232e9b067 PMD 0
[  992.952389] Oops: 0000 [#1] SMP
[  992.953014] Modules linked in: nfsd lockd nfs_acl exportfs auth_rpcgss oid_registry sunrpc bridge stp llc vhost_net macvtap macvlan vhost tun kvm_intel kvm ioatdma ixgbe mdio igb dca
[  992.956042] CPU: 2 PID: 11928 Comm: ifconfig Not tainted 3.16.0-rc6-net-next-07-29-2014-FCoE+ #1
[  992.956915] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.0003.041920141333 04/19/2014
[  992.957791] task: ffff8804341c0000 ti: ffff8801d7dc8000 task.ti: ffff8801d7dc8000
[  992.958660] RIP: 0010:[<ffffffffa003b71e>]  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.959613] RSP: 0018:ffff8801d7dcbbb8  EFLAGS: 00010286
[  992.960093] RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000001
[  992.960575] RDX: ffff880232eb7000 RSI: 0000000000000000 RDI: ffff88022dc05800
[  992.961059] RBP: ffff8801d7dcbbd8 R08: 0000000000000000 R09: 0000000000000000
[  992.961541] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88022ec20980
[  992.962023] R13: ffff880232eb7000 R14: 0000000000000001 R15: 0000000000000001
[  992.962508] FS:  00007fab264887a0(0000) GS:ffff880237640000(0000) knlGS:0000000000000000
[  992.963378] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  992.963858] CR2: 0000000000000056 CR3: 000000022a939000 CR4: 00000000001427e0
[  992.964340] Stack:
[  992.964806]  ffff88022ec28840 ffff88022ec20980 ffff88022dc05800 ffff880232eb7000
[  992.965976]  ffff8801d7dcbc28 ffffffffa003bae8 ffff8801d7dcbbe8 0000000000000400
[  992.967147]  000000000000000d ffff88022ec20980 ffff88022ec20000 ffff88022dc05800
[  992.968319] Call Trace:
[  992.968795]  [<ffffffffa003bae8>] ixgbe_fwd_ring_up+0x88/0x280 [ixgbe]
[  992.969284]  [<ffffffffa0041d83>] ixgbe_fwd_add+0x173/0x220 [ixgbe]
[  992.969767]  [<ffffffffa015056c>] macvlan_open+0x1bc/0x230 [macvlan]
[  992.970256]  [<ffffffff816b8de7>] __dev_open+0xd7/0x150
[  992.970735]  [<ffffffff816b8bd7>] __dev_change_flags+0xa7/0x170
[  992.971220]  [<ffffffff816b8ccb>] dev_change_flags+0x2b/0x70
[  992.971703]  [<ffffffff817471b2>] devinet_ioctl+0x602/0x6d0
[  992.972184]  [<ffffffff81748168>] inet_ioctl+0x78/0x90
[  992.972666]  [<ffffffff816a143b>] sock_do_ioctl+0x2b/0x70
[  992.973146]  [<ffffffff816a14ed>] sock_ioctl+0x6d/0x260
[  992.973627]  [<ffffffff811ad3b4>] do_vfs_ioctl+0x84/0x540
[  992.974109]  [<ffffffff811a4c81>] ? final_putname+0x21/0x50
[  992.974593]  [<ffffffff818725d5>] ? sysret_check+0x22/0x5d
[  992.975073]  [<ffffffff811ad901>] SyS_ioctl+0x91/0xa0
[  992.975550]  [<ffffffff818725a9>] system_call_fastpath+0x16/0x1b
[  992.976026] Code: ff 66 66 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 48 83 ec 20 48 89 5d e8 4c 89 65 f0 48 89 f3 4c 89 6d f8 4c 8b a7 08 02 00 00 <44> 0f b6 6e 56 44 03 af 14 02 00 00 4c 89 e7 e8 5e f2 ff ff be
[  992.982261] RIP  [<ffffffffa003b71e>] ixgbe_disable_fwd_ring+0x1e/0xf0 [ixgbe]
[  992.983212]  RSP <ffff8801d7dcbbb8>
[  992.983681] CR2: 0000000000000056
[  992.984248] ---[ end trace 9f54802b5cc3638b ]---

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The contents of this patch were originally generated by
"scripts/checkpatch.pl --fix-inplace --types CODE_INDENT,LEADING_SPACE
drivers/net/ethernet/ixgbe/*.[ch]", and then hand verified for
consistency.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>