Commit "ath9k_hw: remove ATH_BTCOEX_CFG_MCI" removed
MCI as a separate coex scheme, but we need it to
avoid fiddling with GPIO registers during
ath9k_init_btcoex() that are meant only for 3-wire
cards.

Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

- Use generic bitops instead of custom hackery
- Move interrupt enable/disable logic from ath9k to ath9k_hw
- Decouple ISR call from btcoex
- Make the overflow callback optional (to prevent IRQ storms)
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On lower WLAN signal strength, WLAN downlink traffic might suffer
from retransmissions. At the mean time, playing SCO/A2DP profiles
is affecting WLAN stability. In such scenario, by stomping SCO/A2DP
BT traffic completely for a BTCOEX period, gives WLAN traffic an
oppertunity to recover PHY rate. It also improves WLAN stability at
lower RSSI without sacificing BT traffic.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The WLAN/BT weights have to set correctly before BTCOEX
is initialized. Currently, this is not done for all chips
in the AR9003 family. This patch fixes this issue by setting
the weights in the init path. While at it, rename ar9462_wlan_weights
to mci_wlan_weights since it is common to both AR9462 and AR9565.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9462 uses modified version of 3-Wire hw scheme for btcoex.
MCI itself is not a separate hw scheme but it aids to manage
multiple bt profiles. In ar9462, bt priority traffic is identified
by the number of bt profile types instead of gpio. So that this
patch removes MCI hw scheme.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since BTCOEX code can be compiled out cleanly now,
remove these checks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Setting up the required scheme can be done as part of the
BTCOEX initialization path and it doesn't belong in
ath9k_hw_fill_cap_info() anyway.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.

This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.

On MIPS this reduces the total size for the modules by about 20k.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.

Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove all wlan weight macros and group it together for better
understanding & readability. It makes the code reusable for
AR9462 wlan weights.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes btcoex_enable from stomp type change and let
it be called from callee functions that makes the code can be
reusable for MCI changes.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These were getting the macros from an implicit module.h
include via device.h, but we are planning to clean that up.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

drivers/net: Add export.h to wireless/brcm80211/brcmfmac/bcmsdh.c

This relatively recently added file uses EXPORT_SYMBOL and hence
needs export.h included so that it is compatible with the module.h
split up work.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

drivers/net/wireless/ath/ath9k/hif_usb.c +135 hif_usb_mgmt_cb(6) warn:
variable dereferenced before check 'cmd'
drivers/net/wireless/ath/ath9k/btcoex.c +77 ath9k_hw_init_btcoex_hw(38)
error: buffer overflow 'ah->hw_gen_timers.gen_timer_index' 32 <=
2009813776
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Times They Are a-Changin'.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move bt_stomp to ath9k_hw and add its support for latest chipsets.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.

The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hw code will be shared between ath9k and ath9k_htc.
Just a few more files are left to clean up, mark them as well.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also just pass the ath_hw as the parameter.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are only used by btcoex.c on one routine, so stuff them
into that file.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After some necessary cleanups we now move ath9k_hw_btcoex_set_weight()
to where it belongs.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

btcoex_scheme is already part of a btcoex struct, its implied
this is btcoex related.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bt_stomp_type defines the bt coex weight, it has a one-to-one
mapping. In the future we may want to just use the weight directly.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whether or not bluetooth coex has been enabled is a hardware
state and only the hardware helpers will be able to set this.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

One for 2-wire and another for 3-wire.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Keep on btcoex.c only hardware access helpers, move the
driver core specific code to main.c. To accomplish
this we had to split ath_init_btcoex_info() into two parts,
the driver core part -- ath_init_btcoex_timer() and the hw
specific part -- ath9k_hw_init_btcoex_hw_info(). This
highlights how ath_gen_timer is part of the driver core, not
hw related, so stuff that into ath_btcoex struct.

The ath9k_hw_btcoex_init() code is now put inline on
ath_init_softc() through a switch to it easier to follow,
since we did that we can now call ath_tx_get_qnum() from
the main.c instead of btcoex.c
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a helper for 2-wire and another for 3-wire.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since we now access it via the ath_hw declare the ath_hw pointer
at the header of some routines and se it. ath9k.h no longer needs to
access btcoex.h and to adjust for this move ath_btcoex_set_weight()
into btcoex.h and instead give main.c a helper for setting initial
values upon drv_start()
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is some bluetooth coexistance data which is driver
specific, stuff that into its own structure.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>