Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This includes irda, gpio keys, pxafb, backlight, ohci and flash
(read-only).
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch contains the base code to boot the Toshiba e330, e740,
e750, e400, and e800 PDAs.
Signed-off-by: NIan Molton <spyro@f2s.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

registers are retained during standby mode, thus it's not necessary
to save/restore and checksum
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When PXA27x wakes up, tick_resume_oneshot() tries to set a timer
interrupt to occur immediately.  Since PXA27x requires at least
MIN_OSCR_DELTA, this causes us to flag an error.

tick_program_event() then increments the next event time by
min_delta_ns.  However, by the time we get back to programming
the next event, the OSCR has incremented such that we fail again.
We repeatedly retry, but the OSCR is too fast for us - we never
catch up, so we never break out of the loop - resulting in us
never apparantly resuming.

Fix this by doubling min_delta_ns.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The PXA manuals indicate that when in standby or sleep modes, clocks to
peripherals are shut off by the processor itself.  Eg:

PXA270 standby: "In standby mode, all clocks are disabled except those
 for the power manager and the RTC."

PXA270 sleep: "In sleep mode, all clocks are disabled to the processor
 and to all peripherals except the RTC."

PXA255 sleep: "In Sleep Mode, all processor and peripheral clocks are
 disabled, except the RTC."

Therefore, it should be safe to leave the clock enable register alone
prior to entering low power modes for these SoCs.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Wakeup sources on PXA3 are enabled at two levels.  First, the MFP
configuration has to be set to enable which edges a specific pin
will trigger a wakeup.  The pin also has to be routed to a functional
unit.  Lastly, the functional unit must be enabled as a wakeup source
in the appropriate AD*ER registers (AD2D0ER for standby resume.)

This doesn't fit well with the IRQ wake scheme - we currently do a
best effort conversion from IRQ numbers to functional unit wake enable
bits.  For instance, there's several USB client related enable bits but
there's no corresponding IRQs to determine which you'd want.  Conversely,
there's a single enable bit covering several functional units.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Hook the MFP code into the power management code so that the MFPs can
be reconfigured when suspending and resuming.  However, note the FIXME
- low power mode MFP configuration may depend on the system state being
entered.

Also note that we have to clear any detected edge events prior to
entering a low power mode - otherwise we immediately wake up.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:

   1. power management sometimes requires the MFP to be configured
      differently when in run mode or in low power mode

   2. for future integration of pxa{25x,27x} GPIO configurations

The modifications include:

1. introducing of processor independent MFP configuration bits, as
   defined in [include/asm-arm/arch-pxa/mfp.h]:

	bit  0.. 9 - MFP Pin Number (1024 Pins Maximum)
	bit 10..12 - Alternate Function Selection
	bit 13..15 - Drive Strength
	bit 16..18 - Low Power Mode State
	bit 19..20 - Low Power Mode Edge Detection
	bit 21..22 - Run Mode Pull State
	and so on,

2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h

3. cleaning up of the MFPR bit definitions

4. mapping of processor independent MFP configuration into processor
   specific MFPR register settings is now totally encapsulated within
   pxa3xx_mfp_config()

5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
   according to Documentation/CodingStyle Chapter 5, usage of this
   in platform code will be slowly removed in later patches
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no point building standby/sleep code for processors which
aren't configured.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PXA3 has a different memory controller from PXA2 platforms.  Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The mapping for physical address 0x48000000 is not sufficient
to allow access to the dynamic memory controller configuration
registers on PXA3.  These registers need to be accessed to
reconfigure the SDRAM when waking from a low power mode.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch is to add the third mmc controller support _only_
for pxa310.

On zylonite, the third controller support one slot.
Signed-off-by: NBridge Wu <bridge.wu@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch is to add the second mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.

On zylonite, the second controller has no slot.
Signed-off-by: NBridge Wu <bridge.wu@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.

On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: NBridge Wu <bridge.wu@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Considering that generic.c is getting more and more bloated by device
information, moving that part out side will be much cleaner.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

FFUART and friends are already defined as __REG(x) in pxa-regs.h.
Instead of redefining them here, we can just provide the __REG macro.
Including asm/arch/hardware.h is not an option because this physical
addresses are needed here.
This is a fix for the compiler warnings generated by 4663/1.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.

It is applicable to all pxa platforms.
Signed-off-by: NBridge Wu <bridge.wu@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.

This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.
Signed-off-by: NBridge Wu <bridge.wu@marvell.com>
Acked-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors.  It's about time we applied one.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initialise the SSP driver at arch_initcall() time, so it's available
for other drivers to use it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Only register the "cpld_irq" sysclass for mainstone/lubbock if we're
running on one of those platforms.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
   information of the designated SSP port.

2. remove those IRQ/memory request code, ssp_request() has done that for
   the driver

3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
   has to be defined, all will be retreived by ssp_request()

4. introduce ssp_get_clk_div() to handle controller difference in clock
   divisor setting

5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
   handle the different SSP clock frequency between different processors
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. change SSP register definitions from absolute virtual addresses to
   offsets

2. use __raw_writel()/__raw_readl() for functions of ssp_xxxx()
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. define "struct ssp_device" for SSP information, which is requested
   and released by function ssp_request()/ssp_free()

2. modify the ssp_init() and ssp_exit() to use the interface
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Also, use existing register and bit definitions instead of numbers.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Replace wakeup support using the alarm via the SA1100 RTC driver on
SA1100 and PXA platforms.  This allows RTC alarm wakeup to be enabled
via sysfs using the conventional attributes.
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>