1. 08 2月, 2015 1 次提交
  2. 20 1月, 2015 2 次提交
  3. 15 1月, 2015 1 次提交
  4. 14 1月, 2015 1 次提交
  5. 13 1月, 2015 2 次提交
  6. 07 1月, 2015 1 次提交
  7. 10 12月, 2014 1 次提交
    • H
      r8152: redefine REALTEK_USB_DEVICE · d9a28c5b
      hayeswang 提交于
      Redefine REALTEK_USB_DEVICE for the desired USB interface for probe().
      There are three USB interfaces for the device. USB_CLASS_COMM and
      USB_CLASS_CDC_DATA are for ECM mode (config #2). USB_CLASS_VENDOR_SPEC
      is for the vendor mode (config #1). However, we are not interesting
      in USB_CLASS_CDC_DATA for probe(), so redefine REALTEK_USB_DEVICE
      to ignore the USB interface class of USB_CLASS_CDC_DATA.
      Signed-off-by: NHayes Wang <hayeswang@realtek.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d9a28c5b
  8. 22 11月, 2014 2 次提交
  9. 13 11月, 2014 3 次提交
  10. 07 11月, 2014 3 次提交
  11. 06 11月, 2014 1 次提交
  12. 01 11月, 2014 1 次提交
    • H
      r8152: stop submitting intr for -EPROTO · d59c876d
      hayeswang 提交于
      For Renesas USB 3.0 host controller, when unplugging the usb hub which
      has the RTL8153 plugged, the driver would get -EPROTO for interrupt
      transfer. There is high probability to get the information of "HC died;
      cleaning up", if the driver continues to submit the interrupt transfer
      before the disconnect() is called.
      
      [ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
      [ 1024.383097] usb 9-1: USB disconnect, device number 2
      [ 1024.383103] usb 9-1.4: USB disconnect, device number 6
      [ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
      [ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
      [ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
      [ 1029.421480] usb 8-1: USB disconnect, device number 2
      Signed-off-by: NHayes Wang <hayeswang@realtek.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d59c876d
  13. 31 10月, 2014 4 次提交
  14. 30 10月, 2014 2 次提交
  15. 18 10月, 2014 1 次提交
  16. 10 10月, 2014 3 次提交
  17. 07 10月, 2014 1 次提交
  18. 04 10月, 2014 1 次提交
  19. 02 10月, 2014 2 次提交
  20. 01 10月, 2014 1 次提交
  21. 29 9月, 2014 3 次提交
  22. 27 9月, 2014 1 次提交
  23. 23 9月, 2014 1 次提交
    • H
      r8152: disable ALDPS · d70b1137
      hayeswang 提交于
      If the hw is in ALDPS mode, the hw may have no response for accessing
      the most registers. Therefore, the ALDPS should be disabled before
      accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
      and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
      wouldn't enter ALDPS mode when linking on. The hw would enter the
      ALDPS mode after several seconds when link down occurs and the ALDPS
      is enabled.
      Signed-off-by: NHayes Wang <hayeswang@realtek.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d70b1137
  24. 14 9月, 2014 1 次提交
反馈
建议
客服 返回
顶部