Add the OCM RAM IP block and interconnect data.  This is an oh-chip
block of SRAM connected directly to the L3 bus.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>

Add the OCP2SCP IP block and interconnect data.  The OCP2SCP can be
used in conjunction with the on-chip embedded USB PHY, associated with
the OTG controller.

Add the on-chip full-speed USB host controller IP block and
interconnect data.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add the SL2 interface IP block and interconnect data.  The SL2 is related
to the IVA-HD subsystem.

Add IP block and interconnect data for the C2C ("Chip-to-chip")
interconnect.  This can provide a direct system interconnect link to
other devices stacked on the OMAP package.

Add the ELM IP block and interconnect data.  The ELM can be used
to locate errors in NAND flash connected to the GPMC.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>

Add the McASP hwmod and associated interconnect data.  The McASP is a
general-purpose audio serial port.
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add the Slimbus hwmods and associated interconnect data.  The Slimbus
IP blocks implement a two-wire serial interface.
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add the GPU hwmod and associated interconnect data.  The GPU is a
graphics accelerator.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>

Add the EMIF1 and 2 hwmods and associated interconnect data.  The EMIFs
are SDRAM interface IP blocks.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>

Add the GPMC hwmod and associated interconnect data.   The GPMC is a
programmable parallel-bus memory controller.
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add the HDQ/1-wire hwmod and associated interconnect data.  The
HDQ/1-wire IP block is a low-speed serial interconnect.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>

Add hwmod data for the OMAP4 FDIF IP block.

This patch also includes a change (originally from Fernando Guzman
Lugo <fernando.lugo@ti.com>) to set a softreset delay for the FDIF IP
block:

   http://www.spinics.net/lists/arm-kernel/msg161874.htmlSigned-off-by: NMing Lei <ming.lei@canonical.com>
Acked-by: NBenoît Cousson <b-cousson@ti.com>
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: rearranged to match script output; fixed FDIF end address to
 match script data; wrote trivial changelog; combined the FDIF portion of
 Fernando's srst_udelay patch]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The PRM and CM implicit clockdomains will soon be used by OMAP44xx.
So, make them common to OMAP2+ and modify the OMAP4 clockdomains code
so use of these clockdomains doesn't crash the system.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>

N800 logs this message on boot:

[    0.182281] omap_hwmod: iva: cannot be enabled for reset (3)

Fix by creating basic IVA1 and DSP hwmods for OMAP2420, and a basic IVA2
hwmod for OMAP2430.  There is still more information to be added, but
this should resolve the immediate issue.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The IVA hwmod data is missing some fields that cause the following
warning on boot:

[    0.118011] omap_hwmod: iva: cannot be enabled for reset (3)

Fix by encoding the IP block's main functional clock, reset lines, and
clockdomain.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The OMAP3 hwmod data listed iva2_ck as an interface clock between the
IVA and L3.  This is incorrect.  iva2_ck is not an interface clock.
Since it cannot auto-idle, specifying it here prevents the IVA and at
least one of the CORE clockdomains from going idle, which causes PM
problems such as these upon system suspend:

[   70.626129] Powerdomain (iva2_pwrdm) didn't enter target state 1
[   70.626190] Powerdomain (core_pwrdm) didn't enter target state 1

Fix by specifying the actual interface clock in the hwmod data.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Several struct omap_hwmod_ocp_if records can be shared between OMAP2420
and OMAP2430.  Move these shared records out of the chip-specific files
into mach-omap2/omap_hwmod_2xxx_interconnect_data.c.  This should save some
memory and source lines, at the cost of readability.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

After the link registration conversion, it's much easier to share some
hwmod data between OMAP2420 and 2430.  Move the shareable data into a
common file.  This should save some memory and lines of source, at the
cost of readability.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Reorganize the hwmod data to declare the IP blocks first and the
interconnects second.  This allows us to remove the forward
declarations, which this patch also does. Saves some lines of source
data.  While here, take the opportunity to synchronize the order of
the OMAP44xx hwmod data with the autogenerator output -- it's slightly
different due to past mismerges -- and fix a few minor typos and
whitespace problems in the files.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Now that the data has been converted to use interface registration, we
can remove the (now unused) direct hwmod registration code.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Register interconnect links between IP blocks, rather than the IP
blocks themselves.  (The IP blocks will be registered as a side-effect
of registering the links.)

The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs.  These
objectives come at the penalty of increased boot time due to increased
computation.

While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Add support for direct IP block interconnect ("link") registration to
the hwmod code via a new function, omap_hwmod_register_links().  This
will replace direct registration of hwmods, and a subsequent patch
will remove omap_hwmod_register().

This change will allow a subsequent patch to remove the hwmod data
link arrays.  This will reduce the size of the hwmod static data and
also make it easier to generate the data files.  It will also make it
possible to share some of the struct omap_hwmod records across
multiple SoCs, since the link array pointers will be removed from the
struct omap_hwmod.

The downside is that boot time will increase.  Minimizing boot time
was the reason why the link arrays were originally introduced.
Removing them will require extra computation during boot to allocate
memory and associate IP blocks with their interconnects.  However,
since the current kernel development focus is on reducing the number
of lines in arch/arm/mach-omap2/, boot time impact is now seemingly
considered a lower priority.

This patch contains additional complexity to reduce the number of
memory allocations required for this change.  This reduces the boot
time impact: total hwmod link registration time was ~ 2655
microseconds with a simple allocation strategy, but is now ~ 549
microseconds[1] with the approach taken by this patch.

1. Measured on a BeagleBoard 35xx @ 500MHz MPU/333 MHz CORE, average
   of 7 samples.  Total uncertainty is +/- 61 microseconds.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

An IP block's MPU interface port only needs to be found once.  The result
can be cached to speed further lookups.  This patch consolidates these
two steps into a single function.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

To reduce the number of lines of data in the OMAP portion of the Linux
code base, subsequent patches will remove the lists of hwmod
interconnect links from the static hwmod data.  These lists will be
built dynamically during boot.  To ease this transition, this patch
centralizes the way that interconnect links are iterated into a single
function, _fetch_next_ocp_if().
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Most IP blocks on the OMAP SoC have an interconnect link that is
intended to be used by the MPU to communicate with the IP block.
Several parts of the hwmod code need to be able to identify this link.
Currently, this is open-coded.  However, future patches will change
the way that interconnect links are represented and will make
identifying the link more complex.  So to avoid code duplication, this
patch centralizes the MPU port link identification code into a new
function, _find_mpu_rt_port().
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Some hwmods were commented out from the OMAP4 data, under the theory
that they shouldn't be added until drivers were ready.  But part of
the utility of the hwmod code is that it can reset and properly
initialize IP blocks that have no drivers associated with them.
Rather than commenting the links in the future hwmod data conversion
patches, discussing this with Benoit, it seems best to simply
uncomment them now.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set.  This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Commit 407a6888 ("OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU") adds a
hwmod for the bandgap die temperature sensor IP block.  This IP block
has no interconnect port or firewall region, nor does it have an
independent register space or OCP control registers.  Its registers
are embedded in the System Control Module (SCM) IP block.  So it
appears that the bandgap device should be created by the SCM driver.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

GPTIMER12 is attached to the L4 SEC interconnect, not directly to L4 WKUP.
Add the L4 SEC interconnect and attach GPTIMER12 to it.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The OMAP3 hwmod data was missing a DSS->L3 interconnect link for the
OMAP3430 ES1 DSS hwmod.  Since the hwmod code and data is being modified
to register interfaces rather than hwmods, this would result in the DSS hwmod
not being registered correctly on OMAP3430ES1.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit a52e2ab6 ("ARM: OMAP3: hwmod
data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1")
didn't link the MMC hwmods to the interconnects correctly.  Future
patches will register hwmods by interface, so if this is not fixed,
the MMC IP blocks won't be registered.  Update the interface data
records to point to the correct IP blocks.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Some of the 2xxx and 3xxx hwmod data files use the old naming style
for hwmods, ending in a "_hwmod".  These names are used by the OMAP
integration code to map hwmods to platform_devices, so they need to be
consistent, or the platform_devices won't be created.  Remove the
_hwmod suffix to conform with the rest of the OMAP SoC data.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

arch/arm/mach-omap2/timer.c pokes around inside the hwmod data
structures.  Since the hwmod data structures are about to change, this
code will break.  This patch modifies the timer code to use
recently-added hwmod functions instead.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>

The timer integration code pokes around in hwmod data structures.
Those data structures are about to change.  Define a function,
omap_hwmod_get_resource_byname(), for the timer integration code to
use instead.

The original patch has been changed to use struct resource by Tony's
request, although the caller of this function should not be a driver._
Platform drivers should get their data through the regular platform_*
functions; DT drivers through the appropriate of_* functions.  This a
function is only for use by OMAP core code in arch/arm/*omap*.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

A subsequent patch will need to know the struct omap_hwmod_addr_space
record corresponding to the module's register target, used by the MPU.
So, convert _find_mpu_rt_base() into _find_mpu_rt_addr_space().  Then
modify its sole current user, _populate_mpu_rt_base(), to extract the
MPU RT base address itself from the struct omap_hwmod_addr_space record.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Change the way that hardreset lines are handled by the hwmod code.
Hardreset lines are generally associated with initiator IP blocks.
Prior to this change, the hwmod code expected to control hardreset
lines itself, asserting them on shutdown and deasserting them upon
enable.  But driver authors inside TI have commented to us that their
drivers require direct control over these lines.  Unfortunately, these
drivers haven't been posted publicly yet, so it's hard to determine
exactly what is needed, a priori.  This change attempts to set forth
some reasonable semantics that should be an improvement over the
current code.

The semantics implemented by this patch are as follows:

- If the hwmod is not marked with HWMOD_INIT_NO_RESET, then assert all
  associated hardreset lines during IP block setup.  This is intended
  to place the IP blocks into a known state that will not interfere
  with other devices during kernel boot.

- IP blocks with hardreset lines will not be automatically enabled or
  idled during setup.  Instead, they will be left in the INITIALIZED
  state.

- When the hwmod code is asked to enable, idle, or shutdown an IP
  block with asserted hardreset lines, the hwmod code will do nothing.
  The driver integration code must do the remaining work needed to
  control these IP blocks.  Once this driver integration code is posted
  to the lists, hopefully we can consolidate it and move it inside the
  hwmod code.

Custom reset functions for IP blocks with hardreset lines still should
be supported and are strongly endorsed.  It is intended that every
subsystem with hardreset lines should have a custom reset function
that can place their subsystem into quiescent idle with the hardreset
lines deasserted.

This reverts most of commit 5365efbe
("OMAP: hwmod: Add hardreset management support").  Later code
reorganizations caused the sequencing of the code from this patch to
be changed, anyway.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Reorganize the code involved in resetting and configuring an IP block
to make it easier to read and maintain.  This involves improving
documentation, splitting some large functions up into smaller ones to
better conform with Documentation/CodingStyle, and removing some
unnecessary code.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Reorganize the code involved in initializing the internal data for
each hwmod to make it easier to read and maintain.  This involves
improving documentation and removing some duplicated and unnecessary
code.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Revise the IP block reset process.  This patch ensures that the
OCP_SYSCONFIG registers are reloaded after a custom reset.  Since
OCP_SYSCONFIG bits are cleared during reset, they should be
reprogrammed unless the IP block is being left in reset.  (The only IP
blocks that are left in reset are IP blocks with hardreset lines and
no custom reset function.)  If the IP block is left in reset, then it
is inaccessible to the MPU, and an access to the OCP_SYSCONFIG
register will cause an abort.

This version incorporates comments from Omar Ramirez Luna
<omar.ramirez@ti.com> to skip the OCP_SYSCONFIG access after asserting
hardreset lines.  This allows the MMU (IOMMU) IP block, which has
both hardreset lines and an OCP_SYSCONFIG register.

Also, ignore _ocp_softreset() errors if the IP block doesn't include a
softreset bit.  This is needed since a subsequent patch will start
taking the return value of the _reset() function seriously.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>

Remove the pseudo-hwmods associated with hardreset lines from the
OMAP4 data file.  Future patches will convert this data to register
hwmods by interfaces, rather than registering hwmods directly.  The
pseudo-hwmods aren't associated with any interfaces, so this will
create a problem.

After this change, the hwmod code will reset processor IPs at the
hwmod level, rather than by individual hardreset lines.  So, for
example, if the IVA device driver code wishes to place one of the
sequencer cores into reset, while leaving the other active, it must do
so itself by calling the appropriate PRM functions.

This patch will cause a change in the initialization behavior of the
DSP, IVA, and IPU.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Parts of the hwmod code test to see if a module has one and only one
hardreset line before taking an action.  It seems more appropriate
to control all hardreset lines associated with a hwmod, not just one.

It so happens that with the current hwmod data, this patch will not
change any behavior, since hwmods with hardreset lines have only one
hardreset line associated with them, and 'pseudo-hwmods' are used to
handle the other hardreset lines.  But future hwmod data patches to
remove the pseudo-hwmods will change this.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.

Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick".  This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.
Signed-off-by: NArchit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>