Cc: Dan Kegel <dank@kegel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Xavier Bestel <xavier.bestel@free.fr>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* remove trailing whitespaces
* 'if()' -> 'if ()'
* remove extra new-line before EXPORT_SYMBOL_GPL()
* add extra new-line after 'id' definition
* respect 80-columns limit

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add missing checks for control register existence (some legacy m68k specific
IDE controllers don't have it).  Also use drive->ctl while at it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add more TSST (Toshiba/Samsung) drives to the
'broken cable detection' blacklist.

Signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Port of Jeff's libata commit 54174db3
("[libata] ata_piix: add HP compaq laptop to short cable list").

Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Port of Alan's patch for pata_ali.c.

Cc: Alan Cox <alan@redhat.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on the report from snowbat@gmail.com.

Fixes kernel bugzilla bug #9195.

Tested-by: snowbat@gmail.com
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drivers/ide/pci/amd74xx.c: In function `init_hwif_amd74xx':
drivers/ide/pci/amd74xx.c:387: error: implicit declaration of function `pci_get_legacy_ide_irq'

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Don't override ide_register_hw() result and check if there is a hwif
  available to use.

* MAX_HWIFS is user configurable nowadays so replace it by hard-coded value.

* Remove the comment about ide_hwifs[].
Acked-by: NMikael Starvik <starvik@axis.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ETRAX_IDE and friends from arch/cris/arch-{v10,v32}/drivers/Kconfig
  to drivers/ide/Kconfig.

* Don't force selecting ide-disk and ide-cd device drivers
  (please handle this through defconfig if necessary).

* Make ETRAX_IDE depend on BROKEN for the time being
  (it doesn't even compile currently).

Cc: Mikael Starvik <starvik@axis.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add a separate config option for ide-8300 host driver instead of depending
on CONFIG_H8300.

This change is a preparation for the future changes and also allows ide-h8300
to be disabled if needed.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Only LWMON, IVMS8, IVML24 and TQM8xxL platforms have the needed
defines (IDE0_BASE_OFFSET and friends) in the platform header file.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add pci_enable_device() to aec62xx probe function
before doing any I/O.

Original probe function tries to read from device's
PCI region 4 before calling ide_setup_pci_device().
Since the device is not enabled at this point,
on machines that have no firmware PCI initialization
(e.g. ASUS WL-700gE router), corresponding PCI BAR 
is 0 and the following inb() causes a kernel oops.
Signed-off-by: NAleksandar Radovanovic <biblbroks@sezampro.yu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There is a problem in some hardware where the kernel will stall for
35 seconds waiting for disks that don't exist. This patch will skip
waiting for the BSY-bit on IDE drives to go away if you set "hdx=noprobe"
as a kernel option and the disk is not marked as 'present' (like when
you set the geometry by hand).

If no noprobe-option is set the code will work (more or less) as the
original but if set the code will skip the ide_wait_not_busy() for
that drive. Even if there would be a drive there and it is still busy
afterwards it should not matter since it isn't probed for later.

The code also honors the MAX_DRIVES variable instead of assuming that
there will be two harddrives on the bus.

Bart: minor cleanups
Signed-off-by: NJonas Stare <jonas.stare@purplescout.se>
CC: Andrew Morton <akpm@linux-foundation.org>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The intent behind siimage_reset() was probably to hard reset the interface and
the SATA PHY but as the code writes to two reserved bits instead, it obviously
has been ineffective from the start. So, just remove it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix handling of the PIO modes for the pre-EIDE drives that did not support
the PIO Flow Control Transfer Mode value (00001 nnn) of the Set Transfer Mode
feature by skipping the actual mode programming.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix ide-cris, cs5530, sc1200 and sis5513 host drivers to just return instead
of OOPS-ing for unsupported modes in ->set_dma_mode methods.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use drive->select.all for REQ_TYPE_ATA_TASK requests in execute_drive_cmd()
(the obsolete bits 7 and 5 of the Device register need to be set).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

We can skip conservative PIO "downgrade" (PIO3 becomes PIO2 etc.) on PMAC.

Problem reported by Mikael.

Cc: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

LILO version 16 was released on 26-02-1995 (sic), so telling people to not use
older versions no longer has any value.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make sure to not clear the other IDE channel's interrupt when clearing an IDE
interrupt via the MRDMODE register.

Thanks to Bart for finding a coding mistake.

Bart:

This fixes regression from commit 66602c83
("cmd64x: use interrupt status from MRDMODE register (take 2)").

Extra thanks to Martin for reporting and bisecting the issue.

From: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: NMartin Rogge <marogge@onlinehome.de>
Tested-by: NMilan Kocian <milon@wq.cz>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

commit 33c1002e incorrectly changed return
value from '0' to '-1', fix it (ns87415 was the only host driver affected
since it uses both IDE_HFLAG_TRUST_BIOS_FOR_DMA and IDE_HFLAG_NO_ATAPI_DMA).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Problem reported by Mikael.

Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Noticed by Tejun Heo.

Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_dump_ata_status() may set HOB bit before ide_end_drive_cmd() is called.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drive_cmd_intr() is used by both REQ_TYPE_ATA_CMD and REQ_TYPE_ATA_TASK
but commands using PIO-in protocol are valid only for REQ_TYPE_ATA_CMD
(&args[4] in case of REQ_TYPE_ATA_TASK points to a value for IDE_LCYL_REG
register instead of the data buffer).  This fix allows REQ_TYPE_ATA_TASK
commands to use non-zero values for IDE_SECTOR_REG (args[3]).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This config option is effective only for host drivers that use
IDE_HFLAG_OFF_BOARD host flag (aec62xx, generic, hpt34x, hpt366,
pdc202xx_new, pdc202xx_old and tc86c001).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>