According to hardware design, mem bit must be clear before
entering DSM mode, as ARM core will be power gated in DSM mode.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add suspend support for i.MX6SX.

To enter suspend, echo mem > /sys/power/state.
To exit suspend, using RTC alarm or enable debug UART wakeup.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The pm-imx6q.c works for all i.MX6 SoCs, so let's rename it to pm-imx6.c
and have the build controlled by option CONFIG_SOC_IMX6.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

When CONFIG_SUSPEND is not enabled, we should reasonably skip the call
to imx6q_suspend_init().
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Rename function imx6q_ocram_suspend_init() to imx6q_suspend_init() and
call suspend_set_ops() from there.  Now we get a centralized function
for suspend initialization.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

i.MX6SL's suspend in ocram function is derived from i.MX6Q,
it can lower the DDR IO power from ~10mA@1.2V to ~1mA@1.2V,
measured on i.MX6SL EVK board, SH5.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

i.MX6DL's suspend in ocram function is derived from i.MX6Q,
it can lower the DDR IO power from ~26mA@1.5V to ~15mA@1.5V,
measured on i.MX6DL SabreSD board, R25.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

When system enter suspend, we can set the DDR IO to
high-Z state to save DDR IOs' power consumption, this
operation can save many power(from ~26mA@1.5V to ~15mA@1.5V,
measured on i.MX6Q SabreSD board, R25) of DDR IOs. To
achieve that, we need to copy the suspend code to ocram
and run the low level hardware related code(set DDR IOs
to high-Z state) in ocram.

If there is no ocram space available, then system will
still do suspend in external DDR, hence no DDR IOs will
be set to high-Z.

The OCRAM usage layout is as below,

ocram suspend region(4K currently):
======================== high address ======================
                              .
                              .
                              .
                              ^
                              ^
                              ^
                      imx6_suspend code
             PM_INFO structure(imx6_cpu_pm_info)
======================== low address =======================
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Bit 17 of register CCM_CGPR is called INT_MEM_CLK_LPM as per the mx6
reference manual, so use this name instead.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Use the proper functions. There is no need to fiddle with irq_desc.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>C
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: arm <linux-arm-kernel@lists.infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/20140223212737.099151500@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Since commit 9e8147bb
"ARM: imx6q: move low-power code out of clock driver"
the kernel fails to boot on i.MX6Q/D if preemption is
enabled (CONFIG_PREEMPT=y). The kernel just hangs
before the console comes up.

The above commit moved the initalization of the low-power
mode setting (enabling clocked WAIT states), which was
introduced in commit 83ae2098
"ARM: imx: correct low-power mode setting", from
imx6q_clks_init to imx6q_pm_init. Now it is called
much later, after all cores are enabled.

This patch moves the low-power mode initialization back
to imx6q_clks_init again (and to imx6sl_clks_init).
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

Improve the comment of SW workaround for CCM lpm issue using
hardware errata description to avoid confusion.

ERR007265: CCM: When improper low-power sequence is used, the SoC
enters low power mode before the ARM core executes WFI.

Software workaround:
1) Software should trigger IRQ #32 (IOMUX) to be always pending
   by setting IOMUX_GPR1_GINT.
2) Software should then unmask IRQ #32 in GPC before setting CCM
   Low-Power mode.
3) Software should mask IRQ #32 right after CCM Low-Power mode is
   set (set bits 0-1 of CCM_CLPCR).
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The imx6sl low power mode implementation inherits imx6q/dl one,
and pm-imx6q.c can just work for imx6sl with some minor updates.
Let's enable imx6sl suspend support by reusing pm-imx6q.c and use
cpu_is_imxXX() to handle the those minor differences between imx6sl
and imx6q/dl.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

There is a defect in imx6 LPM design.  When SW tries to enter low power
mode with following sequence, the chip will enter low power mode before
A9 CPU execute WFI instruction:

1. Set CCM_CLPCR[1:0] to 2'b00;
2. ARM CPU enters WFI;
3. ARM CPU wakeup from an interrupt event, which is masked by GPC or not
   visible to GPC, such as interrupt from local timer;
4. Set CCM_CLPCR[1:0] to 2'b01 or 2'b10;
5. ARM CPU execute WFI.

Before the last step, the chip will enter WAIT mode if CCM_CLPCR[1:0] is
set to 2'b01, or enter STOP mode if CCM_CLPCR[1:0] is set to 2'b10.

The patch implements a recommended workaround for this issue.

1. SW triggers irq #32(IOMUX) to be always pending manually by setting
   IOMUX_GPR1_GINT bit;
2. SW should then unmask it in GPC before setting CCM LPM;
3. SW should mask it right after CCM LPM is set (bit0-1 of CCM_CLPCR).
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The WB and RBC configuration calls are currently made from
imx6q_set_lpm() for WAIT_CLOCKED and WAIT_UNCLOCKED mode with a simple
state tracking.  This becomes unnecessary since we can make the calls
from imx6q_pm_enter() directly now for suspend.

More importantly, the current call of imx6q_enable_wb() from
imx6q_set_lpm() is buggy.  The CLPCR register bits configured by
imx6q_enable_wb() will get lost, because imx6q_set_lpm() caches the same
register and write it back at the end of the function.  That's why the
imx6dl suspend/resume does not work currently - the wakeup from suspend
triggers a reset on imx6dl.

Moves the WB and RBC calls into imx6q_pm_enter() to save the state
tracking and fixes above bug, so that suspend/resume can start working
on imx6dl.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The LPM (Low Power Mode) code that currently sits in imx6q clock driver
will be reused by imx6sl.  Let's move it into pm-imx6q.c, so that we
can keep clock driver SoC specific and reuse pm-imx6q.c on imx6sl.

In order to avoid adding another ioremap for CCM block,
imx6q_pm_set_ccm_base() is created to let clock driver set up ccm_base
for pm code.

During the move, the unused CCGR macros get removed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Anatop module have sereval configurations for user
to reduce the power consumption in suspend, provide
suspend/resume interface for further use and enable
fet_odrive to reduce CORE LDO leakage during suspend.

As we have a common anatop file, remove all the operations
of anatop module in other files, use anatop interfaces to
do that.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Building the kernel with allyesconfig fails because the i.mx early
resume code located in the .data section is unable to fixup the bl
relocation as the branch target gets too far away.

The idea of having code in the .data section allows for easy access to
nearby data using relative addressing while the MMU is off. However it
is probably best to move the code back to the .text section where it
belongs and fixup the data access instead.  This solves the bl reloc
issue (at least until this becomes a general problem) and simplifies
the code as well.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The hardware reset value of bit CCM_CLPCR_LPM enables WAIT mode
(WAIT_UNCLOCKED) by default.  However this is undesirable because
WAIT mode should only be enabled when there is a driver managing
ARM clock gating.  Correct the initial power mode to WAIT_CLOCKED
(disable WAIT mode).  While at it, the power mode after resuming
is also set back to WAIT_CLOCKED from STOP_POWER_OFF.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It moves a bunch of header files included in hardware.h and itself
from mach-imx/include/mach to mach-imx, and updates users to include
hardware.h rather than mach/hardware.h.  The files in mach-imx/devices
will need to include "../hardware.h".
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Rename mach-imx/include/mach/common.h to mach-imx/common.h and update
all users to include common.h rather than mach/common.h.

It also removes an unneeded inclusion to common.h in
mach-imx/devices/devices.c.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Original patch from Lothar Waßmann, this patch fixes a building error
when CONFIG_CACHE_L2X0 is not defined.

Cc: Lothar Waßmann <lw@karo-electronics.de>
Signed-off-by: NEric Miao <eric.miao@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It adds suspend/resume support for imx6q.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>