Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 01 5月, 2014 1 次提交
  3. 30 4月, 2014 4 次提交
    • B
      PCI: Fix use of uninitialized MPS value · 1e358f94
      由 Bjorn Helgaas 提交于 
      If "pcie_bus_config == PCIE_BUS_PERFORMANCE", we don't initialize "smpss",
so we pass a pointer to garbage into pcie_bus_configure_set(), where we
compute "mps" based on the garbage.  We then pass the garbage "mps" to
pcie_write_mps(), which ignores it in the PCIE_BUS_PERFORMANCE case.

Coverity isn't smart enough to deduce that we ignore the garbage (it's a
lot to expect from a human, too), so initialize "smpss" to a safe value in
all cases.

Found by Coverity (CID 146454).
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
      1e358f94
    • B
      PCI: Remove dead code · efdd4070
      由 Bjorn Helgaas 提交于 
      "pdev" can never be NULL here, so remove the test.

Found by Coverity (CID 744313).
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
      efdd4070
    • B
      PCI: Remove unnecessary __ref annotations · 10874f5a
      由 Bjorn Helgaas 提交于 
      Some PCI functions used to be marked __devinit.  When CONFIG_HOTPLUG was
not set, these functions were discarded after boot.  A few callers of these
__devinit functions were marked __ref to indicate that they could safely
call the __devinit functions even though the callers were not __devinit.

But CONFIG_HOTPLUG and __devinit are now gone, and the need for the __ref
annotations is also gone, so remove them.  Relevant historical commits:

  54b956b9 Remove __dev* markings from init.h
  a8e4b9c1 PCI: add generic pci_hp_add_bridge()
  0ab2b57f PCI: fix section mismatch warning in pci_scan_child_bus
  451124a7 PCI: fix 4x section mismatch warnings
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
      10874f5a
    • B
      PCI: Fail new_id for vendor/device values already built into driver · 8895d3bc
      由 Bandan Das 提交于 
      While using the sysfs new_id interface, the user can unintentionally feed
incorrect values if the driver static table has a matching entry.  This is
possible since only the device and vendor fields are mandatory and the rest
are optional.  As a result, store_new_id() will fill in default values that
are then passed on to the driver and can have unintended consequences.

As an example, consider the ixgbe driver and the 82599EB network card:

  echo "8086 10fb" > /sys/bus/pci/drivers/ixgbe/new_id

This will pass a pci_device_id with driver_data = 0 to ixgbe_probe(), which
uses that zero to index a table of card operations.  The zeroth entry of
the table does *not* correspond to the 82599 operations.

This change returns an error if the user attempts to add a dynid for a
vendor/device combination for which a static entry already exists.
However, if the user intentionally wants a different set of values, she
must provide all the 7 fields and that will be accepted.

[bhelgaas: drop KVM text since the problem isn't KVM-specific]
Signed-off-by: NBandan Das <bsd@redhat.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAlex Williamson <alex.williamson@redhat.com>
      8895d3bc
  5. 29 4月, 2014 1 次提交
  7. 26 4月, 2014 1 次提交
  9. 15 4月, 2014 1 次提交
  11. 13 4月, 2014 2 次提交
    • M
      sym53c8xx_2: Set DID_REQUEUE return code when aborting squeue · fd1232b2
      由 Mikulas Patocka 提交于 
      This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.

When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.

This function aborts them with DID_SOFT_ERROR.

If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.

The result is that disk returning QUEUE FULL causes request failures.

The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags.  The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags.  The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      fd1232b2
    • V
      drivers: net: xen-netfront: fix array initialization bug · 810d8ced
      由 Vincenzo Maffione 提交于 
      This patch fixes the initialization of an array used in the TX
datapath that was mistakenly initialized together with the
RX datapath arrays. An out of range array access could happen
when RX and TX rings had different sizes.
Signed-off-by: NVincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      810d8ced
  13. 12 4月, 2014 18 次提交
  15. 11 4月, 2014 12 次提交