* Update ath5k_hw_reset and add some more documentation about PHY calibration
 * Fix ath5k_hw_set_power to use AR5K_SLEEP_CTL_SLE_ALLOW for Network sleep
 * Preserve sleep duration field while setting AR5K_SLEEP_CTL
   and reduce delays & checks for register's status (got this from
   decompiling & dumps, it works for me but it needs testing)

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Do an ADC test during reset to match recent regdumps

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Update hw_reset to calculate some of the values we were using as static
 * Increase activation to rx delay

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Correctly attach RF2425
 * Update SREV values for Radio chips
 * Update hw_attach to use new SPENDING values
 * Write a bit after POST for some chips

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Restore saved initial value after POST

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Update list of registers
* Use updated register macros inside hw.c, initvals.c and debug.c

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.

This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.

So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is necessary to set the dongle type on the nsc driver in order to get
it to work correctly.  Thinkpads all appear to use dongle type 9.  This
patch defaults nsc devices with an IBM PnP descriptor to use type 9.
Signed-off-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NBen Collins <ben.collins@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Preface: The "Broadcom" device is on unreleased hardware, so I can't
disclose the actual model.

When the Dell 370 and 410 BT adapters are put into BT radio mode, they
need to be prepared like many other Broadcom adapters.

Also, add quirk Broadcom 2046 devices with HCI_RESET.  Reference for this
bug: https://launchpad.net/bugs/249448Signed-off-by: NMichael Frey <michael.frey@canonical.com>
Signed-off-by: NMario Limonciello <Mario_Limonciello@Dell.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NBen Collins <ben.collins@canonical.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the packed attribute from PofTimStamp_tag in the hysdn driver as the
thing being packed is just an array of chars and so is unpackable.

This deals with a compiler warning:

In file included from drivers/isdn/hysdn/hysdn_boot.c:19:
drivers/isdn/hysdn/hysdn_pof.h:63: warning: 'packed' attribute ignored for field of type 'unsigned char[40]'
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adapt the tg3 driver to use the reworked PCI PM and make it use the
exported PCI PM core functions instead of accessing the PCI PM registers
directly by itself.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix direct casts of pointers to u32 in the InterPhase ATM driver.  These are
all arguments being passed to printk() calls.  So drop the cast and change the
%x to a %p.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.

The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression l;
@@

mutex_lock(l);
... when != mutex_unlock(l)
    when any
    when strict
(
if (...) { ... when != mutex_unlock(l)
+   mutex_unlock(l);
    return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

SH7763 has Ethernet core same as SH7710/SH7712.
Positions of some registry are different, but the basic part is the same.
I add support of ethernet of sh7763 to sh_eth.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Trying to build with CONFIG_NE2000=m fails with:

  scripts/mod/modpost   -o /tmp/tmp/linux-2.6.27-rc1/Module.symvers    -S     -s
ERROR: "NS8390_init" [drivers/net/ne.ko] undefined!

This is because the split of 8390 into pausing and non-pausing
versions was incompletely propagated to ne.c. This fixes it.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

From: Alan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

dm_{read,write}() were doing USB transfers of data on stack, which isn't
allowed. Fix it by kmalloc'ing a temporary buffer.
Clean up the error handling for short transfers while we're at it.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The callers of niu_ethflow_to_class expect zero as error, but it returns
-1 instead.
Signed-off-by: NAndreas Schwab <schwab@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On s2io driver, when you change the interface MTU, it invokes a card
reset, which flush some statistics.  This patch solves this problem, and
also set the net_device->stats as the default statistics structure,
instead of s2io_nic->stats.

To do that, s2io_nic->stats turned into a staging area, where is saved
statistics of the last hardware statistics query. So, the difference
between the current hardware statistics and s2io_nic->stats, is the
value that should be summed up, in order to get the correct statistics
value, even after a reset.
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Recent changes to the IRQ framework have made passing the wrong
trigger type to request_irq() become a fatal error.  In the case
of the enc28j60 driver, it stopped working in my test harness.

(Specifically:  the signal detects "pin change" events, both edges,
not just falling edges.  Similarly, other boards might route it
through an inverter.  Trigger type are board-specific.)

This fixes that problem by the usual fix of expecting board setup
code to have set up the correct IRQ trigger type.  The best known
example of that being x86 setup.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

skb->dev is set by eth_type_trans already.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Starting with FW version 7.0, the driver needs to allow larger images.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reprogram MAC address after resume from Suspend Mem
(Blackfin Hibernate looses all CORE and SYSTEM register content)
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds support for the realtek 8211c phy. The driver must
perform a hardware reset of the phy due to an errata where the phy could
not detect the link.
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The semantic patch I used was this:

@@
expression lock;
identifier flags;
expression subclass;
@@

- unsigned int flags;
+ unsigned long flags;

...

<+...

(
 spin_lock_irqsave(lock, flags)
|
 _spin_lock_irqsave(lock)
|
 spin_unlock_irqrestore(lock, flags)
|
 _spin_unlock_irqrestore(lock, flags)
|
 read_lock_irqsave(lock, flags)
|
 _read_lock_irqsave(lock)
|
 read_unlock_irqrestore(lock, flags)
|
 _read_unlock_irqrestore(lock, flags)
|
 write_lock_irqsave(lock, flags)
|
 _write_lock_irqsave(lock)
|
 write_unlock_irqrestore(lock, flags)
|
 _write_unlock_irqrestore(lock, flags)
|
 spin_lock_irqsave_nested(lock, flags, subclass)
|
 _spin_lock_irqsave_nested(lock, subclass)
|
 spin_unlock_irqrestore(lock, flags)
|
 _spin_unlock_irqrestore(lock, flags)
|
 _raw_spin_lock_flags(lock, flags)
|
 __raw_spin_lock_flags(lock, flags)
)

...+>

This patch was generated using the Coccinelle framework.

Cc: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Cc: Julia Lawall <julia@diku.dk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wireless statistics produced by the RTL8187B driver are not particularly
informative about the strength of the received signal. From the data sheet
provided by Realtek, I discovered that certain parts of the RX header
should have the information necessary to calculate signal quality and
strength. With testing, it became clear that most of these quantities were
very jittery - only the AGC correlated with the signals expected from nearby
AP's. As a result, the quality and strength are derived from the agc value.
The scaling has been determined so that the numbers are close to those
obtained by b43 under the same conditions. The results are qualitatively
correct.

Statistics derived for the RTL8187 have not been changed.

The RX header variables have been renamed to match the quantites described
in the Realtek data sheet.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"mac80211: fix TX sequence numbers" broke rtl8187. This
patch makes the same kind of fix that was done for rt2x00. Note that
this code will have to be reworked for proper sequence numbers on beacons.
In addition, the sequence number has been placed in the hardware state,
not the vif state.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/mac80211_hwsim.c:503:20: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ia64:

drivers/net/wireless/iwlwifi/iwl-led.c: In function `iwl_get_blink_rate':
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, s64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, u64 arg (arg 7)

We do not know what type the architecture uses to impement u64 and s64,
hence we must cast the variables for printing.

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:

	phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
	Please file bug report to http://rt2x00.serialmonkey.com.

This also fixes the mac80211 warning:

	------------[ cut here ]------------
	WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()

which was triggered by the queue error.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00 will only perform configuration changes from
mac80211 when the configuration option has changed.
This means it keeps track of the current active configuration
and will check these values when the config() callback function
is used.

However this causes breakage when the interface has been
brought down and up again, since all stored active values
aren't reset while the registers might have.
This is for example the case with rt61pci antenna registers which
will jump to invalid values when the interface has been started.

To make sure a full configuration takes place after the start()
callback function, a new flag is added which will be checked
during config() and skips the "what's changed" phase.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.

The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression l;
@@

mutex_lock(l);
... when != mutex_unlock(l)
    when any
    when strict
(
if (...) { ... when != mutex_unlock(l)
+   mutex_unlock(l);
    return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.

The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression l;
@@

mutex_lock(l);
... when != mutex_unlock(l)
    when any
    when strict
(
if (...) { ... when != mutex_unlock(l)
+   mutex_unlock(l);
    return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending the RTS/CTS frame fails, we should
free the skb buffer which was created.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>