It's more of an unnecessary micro-optimization and it prevents switching
from long-GI to short-GI in HT20/single-stream for the lowest rate
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we get to association, the AP station already exists and
is marked authenticated, so moving it into IEEE80211_STA_AUTH
again is a NOP, remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Now that we have channel contexts, idle is (pretty
much) equivalent to not having a channel context.
Change the code to use this relation so that there
no longer is a need for a lot of idle recalculate
calls everywhere.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.

The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The functions were added for some sort of Bluetooth
coexistence, but aren't used, so remove them again.
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to be able to predict the next DTIM TBTT
in the driver, add the ability to use timing data
from beacons only with the new hardware flag
IEEE80211_HW_TIMING_BEACON_ONLY and the BSS info
value sync_dtim_count which is only valid if the
timing data came from a beacon. The data can only
come from a beacon, and if no beacon was received
before association it is updated later together
with the DTIM count notification.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

While technically the TSF isn't an IE, it can be
necessary to distinguish between the TSF from a
beacon and a probe response, in particular in
order to know the next DTIM TBTT, as not all APs
are spec compliant wrt. TSF==0 being a DTIM TBTT
and thus the DTIM count needs to be taken into
account as well.

To allow this, move the TSF into the IE struct
so it can be known whence it came.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no way scan BSS IEs can be NULL as even
if the allocation fails the frame is discarded.
Remove some code checking for this and document
that it is always non-NULL.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add debugfs driver callbacks so drivers can add
debugfs entries for interfaces. Note that they
_must_ remove the entries again as add/remove in
the driver doesn't correspond to add/remove in
debugfs; the former is up/down while the latter
is netdev create/destroy.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, cfg80211 will copy beacon IEs from a previously
received hidden SSID beacon to a probe response entry, if
that entry is created after the beacon entry. However, if
it is the other way around, or if the beacon is updated,
such changes aren't propagated.

Fix this by tracking the relation between the probe
response and beacon BSS structs in this case.

In case drivers have private data stored in a BSS struct
and need access to such data from a beacon entry, cfg80211
now provides the hidden_beacon_bss pointer from the probe
response entry to the beacon entry.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently the code assigns channel contexts to VLANs
(for use by the TX/RX code) when the AP master gets
its channel context assigned. This works fine, but
in the upcoming radar detection work the VLANs don't
require a channel context (during radar detection)
and assigning one to them anyway causes issues with
locking and also inconsistencies -- a VLAN interface
that is added before radar detection would get the
channel context, while one added during it wouldn't.

Fix these issues moving the channel context copying
to a new explicit operation that will not be used
in the radar detection code.
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The chandef tracing writes center_freq1 twice, so
that it is always 0 (no driver supports 80+80 yet)
and leaves center_freq2 unset. Fix this mistake.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The messages currently refer to probe request probes,
but on some devices null data packets will be used
instead. Make the messages more generic.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch fixes the problem which was discussed in
"mac80211: Fix PN corruption in case of multiple
virtual interface" [1].

Amit Shakya reported a serious issue with my patch:
mac80211: serialize rx path workers" [2]:

In case, ieee80211_rx_handlers processing is going on
for skbs received on one vif and at the same time, rx
aggregation reorder timer expires on another vif then
sta_rx_agg_reorder_timer_expired is invoked and it will
push skbs into the single queue (local->rx_skb_queue).

ieee80211_rx_handlers in the while loop assumes that
the skbs are for the same sdata and sta. This assumption
doesn't hold good in this scenario and the PN gets
corrupted by PN received in other vif's skb, causing
traffic to stop due to PN mismatch."

[1] Message-Id: http://mid.gmane.org/201302041844.44436.chunkeey@googlemail.com
[2] Commit-Id: 24a8fdadReported-by: NAmit Shakya <amit.shakya@stericsson.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There seems to be no reason, why it has to be limited to 2.4 GHz.
Signed-off-by: NEmanuel Taube <emanuel.taube@gmail.com>
[remove 'local' variable]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The patch "mac80211: clean up mesh sta allocation warning"
moved some mesh initialization into a path which is only
called when the kernel handles peering. This causes a hang
when mac80211 tries to clean up a userspace-allocated
station entry and delete a timer which has never been
initialized.

To avoid this, only do any mesh sta peering teardown if
the kernel is actually handling it.

The same is true when quiescing before suspend.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fix most kernel-doc warnings, for some reason it
seems to have issues with __aligned, don't remove
the documentation entries it considers to be in
excess due to that.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This prepares for using the spinlock instead of krefs
which is needed in the next patch to track the refs
of combined BSSes correctly.

Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Radar is not required for P2P_DEVICE interfaces.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a driver requests a specific regulatory domain after cfg80211 already
has one, a struct ieee80211_regdomain is leaked.
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A new model of the RTL8188CUS has appeared.
Reported-and-tested-by: NThomas Rosenkrantz <tom.rosary@googlemail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this patch off-channel action frames can be transmitted. This
is needed for p2p when two devices need to find each other while
using different social channels.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently netdev gets created possibly after returning from
add_virtual_intf. This is because add_if is handled asynch. This
is wrong and netdev should be up before returning.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove some unused defines and comments. Also use same define
for IE length.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When adding a virtual interface cfg80211 already has taken the
rtnl_lock. So when the netdevice is being registered the
register_netdevice should be used instead of register_netdev.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently there is a sleep after disconnect on del_station. This
timeout is not needed (anymore) and is causing problems with p2p
setup, because remote side disconnects then supplicant will do
del_station and while it waits the 400ms remote side will already
reconnect and that is something supplicant cant handle.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wiphy object holds information about possible netdev
combinations which can be supported. This needs updating for
p2p device. Also p2p device netdev has wrong 80211 iftype.
Limit the change interface support to match the netdev
configuration/combination possibilities.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All interfaces for ifidx is 0 are created ahead and therefor
double registrations for not only bssidx 0, but ifidx 0 should
be ignored in brcfm_add_if.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the stored role in wdev struct to determine AP/GO role. This
simplifies code. Fix stop_ap for GO role.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add module variable with which a p2p0 netdev can be created. This
netdev can be used by wpa-supplicant to configure and set up the
p2p client/GO.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211 api change needs to be applied. this change will be squashed
with introducing commit:

commit 68751daec95b07a74b18aa22b2f9c196991dbe81
Author: Hante Meuleman <meuleman@broadcom.com>
Date:   Mon Nov 26 12:21:27 2012 +0100

    brcmfmac: add support for P2P listen mode.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some rare situations the wpa_supplicant can lock up on a remain
on channel command. Use actual cookies for the remain on channel
related commands and allow for additional remain on channel while
still having one set.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this patch it is possible to send action frames.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Once wpa_supplicant has registered for P2P action frames all received
action frames for the device are passed up to cfg80211.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this update it is possible to create an P2P go. Handle the
p2p go role in creation and the update beacon from cfg80211. Also
store primary bss in global struct. Needed to map cfg device
back to primary device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In preparation of p2p connections update the sta connect setup and
handling routines. Use join iovar and bsscfg commands where
applicable. Handle assoc ind per bsscfg (vif) and generalize
vndr ie setup to support assoc IEs and support all setup types,
e.g. sta, ap and p2p.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>