Without enabling the workaround for ARM errata 430973 thumb
compiled userland crashes randomly on the Nokia N900.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If CLK_SET_RATE_PARENT is set for a clkoutx2 clock, calling
clk_set_rate() on the clock "skips" the x2 multiplier as there are no
set_rate and round_rate functions defined for the clkoutx2.

This results in getting double the requested clock rates, breaking the
display on omap3430 based devices. This got broken when
d0f58bd3 and related patches were merged
for v3.14, as omapdss driver now relies more on the clk-framework and
CLK_SET_RATE_PARENT.

This patch implements set_rate and round_rate for clkoutx2.

Tested on OMAP3430, OMAP3630, OMAP4460.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit 313a76ee (ARM: OMAP2+: hwmod: Fix SOFTRESET logic) introduced
softreset bit cleaning right after set one. It is caused L3 error for
OMAP4 ISS because ISS register write occurs when ISS reset process is in
progress. Avoid this situation by cleaning softreset bit later, when reset
process is successfully finished.
Signed-off-by: NIllia Smyrnov <illia.smyrnov@globallogic.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The spinlock module's SYSCONFIG register on DRA7xx does not
support smart wakeup, and also does not have the CLKACTIVITY
field. The sysc data for spinlock module has been appropriately
fixed up to reflect the same.

Cc: Ambresh K <ambresh@ti.com>
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Use the correct register offset for issuing the
reset command in OMAP5. Since dev_inst is set dynamically
OMAP4 should not be affected by this change.
Signed-off-by: NVaibhav Bedia <vaibhav.bedia@gmail.com>
Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Unfortunatly the device tree for older OMAP35xx Overo cannot be used
with newer OMAP36xx and vice-versa. To address this issue, move most of
the Tobi DTS to a common include file, and create model-specific Tobi
DTS.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gumstix is the correct vendor for all Overo related products.
Reported-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Tobi expansion board can be used with both OMAP35xx-based Overo,
and OMAP36xx-based Overo. Currently the boot is broken with newer
OMAP36xx-based Overo (Storm and alike). Fix include file and
compatible string to be able to boot newer models.

This will break older models. This will be addressed later.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NKevin Hilman <khilman@linaro.org>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 97411608 ("ARM: OMAP2+: Remove legacy support for zoom
platforms") removed the Kconfig symbols MACH_OMAP_ZOOM2 and
MACH_OMAP_ZOOM3. Remove the last usage of the related macros too.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The last caller of machine_is_nokia_n800() was removed in commit
5a87cde4 ("ARM: OMAP2+: Remove legacy booting support for n8x0").
That means that the Kconfig symbol MACH_NOKIA_N800 is now unused. It can
safely be removed.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing compatible property to avoid problems in the future.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

N9/N950 does not boot anymore with 3.14-rc1, because SoC compatible
property is missing. Fix that.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform data for tahvo-usb. This is the last missing piece to get
Tahvo USB working with 3.14.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes: commit 75d3625e
       ARM: OMAP2+: gpmc: add DT bindings for OneNAND

OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for ONENAND driver to probe later. However this does
not happen if generic MTD_ONENAND framework is built as module (CONFIG_MTD_ONENAND=m).

Therefore, when MTD/ONENAND and MTD/ONENAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
ONENAND flash to remain un-detected.

This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_ONENAND=y || CONFIG_MTD_ONENAND=m

CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes: commit bc6b1e7b
       ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND

OMAP SoC(s) depend on GPMC controller driver to parse GPMC DT child nodes and
register them platform_device for NAND driver to probe later. However this does
not happen if generic MTD_NAND framework is built as module (CONFIG_MTD_NAND=m).

Therefore, when MTD/NAND and MTD/NAND/OMAP2 modules are loaded, they are unable
to find any matching platform_device and remain un-binded. This causes on board
NAND flash to remain un-detected.

This patch causes GPMC controller to parse DT nodes when
CONFIG_MTD_NAND=y || CONFIG_MTD_NAND=m

CC: <stable@vger.kernel.org> # 3.9.x+
Signed-off-by: NPekon Gupta <pekon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Does not have an aux supply, and must be non-removable.

Otherwise it is removed during suspend and filesystem gets confused.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It should be ACTIVE_HIGH.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP5, DRA7, AM43xx all have OPPs. So select the same to allow SoC
only configuration boot to work with OPP.
Reported-by: NNikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not
working on EVM-SK board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

BMP085 EOC (End Of Conversion) irq line is connected to
gpio113 on gta04. Set irq properties to have driver using irq
instead polling for EOC.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.

The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels.  Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.

Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:

warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))

Instead enable TI EDMA support from defconfig.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add nodes for the Arasan SDHCI controller to Zynq dts files.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

SMP is a user configurable option, not a hardware feature and should not
be selected.
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled
by tegra_defconfig. However, this config option no longer exists, so
no longer selects DEBUG_FS, and nothing else selects it either. So,
"make tegra_defconfig" no longer enables DEBUG_FS in .config.

Rebuild tegra_defconfig on top of next-20140424, while manually
re-enabling DEBUG_FS.

Reasons for removed entries are:
- I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT
- DRM_PANEL: selected by DRM_TEGRA
- NEW_LEDS: selected by many things; at least VT
- LEDS_CLASS: selected by many things; at least VT
- LEDS_TRIGGERS: selected by many things; at least VT
- COMMON_CLK_DEBUG: no longer exists
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

multi_v7_defconfig was missing a large number of options that were in
tegra_defconfig. This patch adds them. The changes fall into the
following categories:

* Enable more Tegra SoC options/drivers.
* Enable more drivers for Tegra boards.
* Enable more options that are useful for running distros.

The patch removes a few lines as well, simply because those options are
now selected by something else, and "make savedefconfig" removes them. I
verified that the options appear in .config after
"make multi_v7_defconfig".
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This board was missed when converting all the others to proper
abstracted GPIO handling. Fix it up the right way by requesting
and driving GPIO line 0 high through gpiolib to power off the
machine.

Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Commit 78d16321 deleted the
static mappings of the core modules, but this static map is
still needed on the Integrator/CP (not the Integrator/AP).

Restore the static map on the Integrator/CP.
Reported-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This allows us to probe the clock controller devices and boot to a
serial console on all DT enabled MSM platforms.

Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.

Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The same workaround as ff999b8a
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more

Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: NTaras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

On ARM, address size can be 32 bits or 64 bits (if CONFIG_ARCH_PHYS_ADDR_T_64BIT
is enabled).
We can't assume that the grant frame base address will always fits in an
unsigned long. Use phys_addr_t instead of unsigned long as argument for
gnttab_setup_auto_xlat_frames.
Signed-off-by: NJulien Grall <julien.grall@linaro.org>
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>

The use of phys_to_machine and machine_to_phys in the phys<=>bus conversions
causes us to lose the top bits of the DMA address if the size of a DMA address is not the same as the size of the phyiscal address.

This can happen in practice on ARM where foreign pages can be above 4GB even
though the local kernel does not have LPAE page tables enabled (which is
totally reasonable if the guest does not itself have >4GB of RAM). In this
case the kernel still maps the foreign pages at a phys addr below 4G (as it
must) but the resulting DMA address (returned by the grant map operation) is
much higher.

This is analogous to a hardware device which has its view of RAM mapped up
high for some reason.

This patch makes I/O to foreign pages (specifically blkif) work on 32-bit ARM
systems with more than 4GB of RAM.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>

Event channels driver needs to be initialized very early. Until now, Xen
initialization was done after all CPUs was bring up.

We can safely move the initialization to an early initcall.

Also use a cpu notifier to:
    - Register the VCPU when the CPU is prepared
    - Enable event channel IRQ when the CPU is running
Signed-off-by: NJulien Grall <julien.grall@linaro.org>
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>

Add watchdog specific config for kizbox board.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>