Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 28 6月, 2008 1 次提交
  3. 11 6月, 2008 1 次提交
    • A
      powerpc/83xx: new board support: MPC8360E-RDK · b13e9309
      由 Anton Vorontsov 提交于 
      This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.

Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.

Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
   unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
   major SPI rework, GPIO API, etc);
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
      b13e9309
  5. 10 6月, 2008 4 次提交
  7. 09 6月, 2008 1 次提交
    • R
      powerpc: DTS file for the C2K · 61586476
      由 Remi Machet 提交于 
      Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).

Part 1 of 5: DTS file describing the board peripherals.  As far as I
know all peripherals except the FPGA are listed in there (I did not
include the FPGA because a lot of work is needed there).
Signed-off-by: NRemi Machet <rmachet@slac.stanford.edu>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      61586476
  9. 03 6月, 2008 5 次提交
  11. 31 5月, 2008 1 次提交
  13. 29 5月, 2008 3 次提交
  15. 20 5月, 2008 1 次提交
  17. 13 5月, 2008 3 次提交
  19. 07 5月, 2008 1 次提交
  21. 02 5月, 2008 1 次提交
  23. 30 4月, 2008 1 次提交
  25. 29 4月, 2008 3 次提交
  27. 28 4月, 2008 1 次提交
    • Y
      fbdev: powerpc: driver for Freescale 8610 and 5121 DIU · 9b53a9e2
      由 York Sun 提交于 
      The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs

All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0.  Changing pixel clock has no effect
on other fbs.

Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0

required command line parameters to preallocate memory for frame buffer diufb.

optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:

Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60

Bpp
bpp=32, bpp=24, or bpp=16

Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS

Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.

If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      9b53a9e2
  29. 25 4月, 2008 1 次提交
  31. 17 4月, 2008 9 次提交
  33. 15 4月, 2008 3 次提交