Fix regulator kernel-doc warnings:

Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc:	Liam Girdwood <lrg@ti.com>
Cc:	Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This encodes the voltage shifts (the number of bits to shift
the register to get to the selector) into the regulator info.
We have several new variants of the AB8500 so this varies a
lot.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix the following:

  CC [M]  drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_probe':
drivers/regulator/max8907-regulator.c:297:12: error: 'max8907_matches' undeclared (first use in this function)

by removing direct references to max8907_matches[], which only exists when
CONFIG_OF is defined.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add missing platform_get_drvdata() call in max8907_regulator_remove(), this
fixes below build warning:

  CC [M]  drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_remove':
drivers/regulator/max8907-regulator.c:353:23: warning: 'pmic' is used uninitialized in this function [-Wuninitialized]
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For linear voltage mapping, the n_voltages is (max - min) / step + 1
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fixes this build error:

drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1229:3: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]

Also added string.h for kmemdup().
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.

The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>

Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>

During upstreaming, I (swarren):
* Converted to regmap.
* Allowed probing from device tree.
* Reworked the regulator driver to be represented as a single device that
  provides multiple regulators, rather than as a device per regulator.
* Replaced many regulator ops with standard functions.
* Added ability to specify supplies for each regulator.
* Removed the WLED regulator. If/when we expose this in the driver, it
  should be a backlight object not a regulator object.
* Renamed from max8907c->max8907, since the driver covers at least the
  C and B revisions.
* General cleanup.
Signed-off-by: NGyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

I currently carry the series to make of_device_id->data const in the
arm-soc tree, which fixes a number of issues, but leaves one new
compiler warning about the twl-regulator driver:

drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1130:8: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]
drivers/regulator/twl-regulator.c:1139:9: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]

The warning indicates that the driver takes a static table with
initialization data for each regulator, modifies the data in place
and passes a pointer to that structure to the regulator_register
function. This is probably ok because a system contains only one
instance of each regulator, but it's still bad style because any
driver should be written to support multiple instances of the same
hardware.

This patch changes the code to dynamically allocate the memory
we pass to the regulator core so the table can be constant.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The regulators should be tending to the maximum in the available range and
consumers should specify the widest range possible.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

MAX77686_REGULATORS is known in compile time.
Use array to save pointer to rdev makes the code simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

To set REGULATOR_MODE_IDLE mode, what we do is to clear DC1_ACTIVE and
DC1_SLEEP bits, this can be done in one wm8400_set_bits() call.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

wm831x_reg_read() returns negative error code on failure.
This prevents using the error code as the value read.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Below is the buck_pmap mapping table:

BUCK1:  mask = 1 << 0,  shift = 0
BUCK2:  mask = 1 << 1,  shift = 1
BUCK3:  mask = 1 << 2,  shift = 2
BUCK4:  mask = 1 << 3,  shift = 3

The mask and shift can be easily calculated by:
        mask = 1 << BUCK_ID
        shift = BUCK_ID

This patch defines BUCK_FPWM_MASK and BUCK_FPWM_SHIFT macros to replace
buck_pmap mapping table.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We already know the mask in lp8788_init_dvs() function, and we can update
the corresponding bit for default_dvs_mode in lp8788_init_dvs() function.
This function looks not necessary to me.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For fixed voltage, the n_voltages should be 1 rather than 0.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use mc13xxx_reg_rmw rather than a mc13xxx_reg_read and a mc13xxx_reg_write calls.

This logic to set MC13892_SWITCHERS0_SWxHI bit is pretty simple:

if (volt > 1375000)
        set MC13892_SWITCHERS0_SWxHI bit
else if (volt < 1100000)
        clear MC13892_SWITCHERS0_SWxHI bit
else
        leave MC13892_SWITCHERS0_SWxHI bit untouched

We already know the selector, so we don't need to calculate the selector again.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Then we can remove lock/unlock around the caller.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Then we can remove lock/unlock around the caller.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The voltage selection logic is supposed to find the samllest voltage falls
within specified range. When using equation to calculate vsel, we need to
ensure the requested min_uV meet the range of using the equation.
Otherwise we may select a voltage that is out of specified range.

For example, in the case vsel = 62 means select voltage of 2100000uV.
What we want is to ensure the requested min_uV <= 2100000 rather than checking
max_uV >= 2100000. And this also means in the case min_uV > 2100000, vsel = 62
does not meet the request.

Also calling twl6030smps_list_voltage() for all cases to ensure the selected
voltage still in bounds.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This was missing until now and the underlying
_regulator_do_set_voltage is using this value when calling list_voltage.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The number of regulator is known at compile time, use array to save pointer to
rdev makes the code simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Pull drm fixes from Dave Airlie:
 "Intel: edid fixes, power consumption fix, s/r fix, haswell fix

  Radeon: BIOS loading fixes for UEFI and Thunderbolt machines, better
  MSAA validation, lockup timeout fixes, modesetting fixes

  One udl dpms fix, one vmwgfx fix, a couple of trivial core changes.

  There is an export added to ACPI as part of the radeon bios fixes.

  I've also included the fbcon flashing cursor vs deinit race fix, that
  seems the simplest place to start"

Trivial conflict in drivers/video/console/fbcon.c due to me having
already applied the fbcon flashing cursor vs deinit race fix, and Dave
had added a comment in there too.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
  fbcon: fix race condition between console lock and cursor timer (v1.1)
  drm: Add missing static storage class specifiers in drm_proc.c file
  drm/udl: dpms off the crtc when disabled.
  drm: Remove two unused fields from struct drm_display_mode
  drm: stop vmgfx driver explosion
  drm/radeon/ss: use num_crtc rather than hardcoded 6
  Revert "drm/radeon: fix bo creation retry path"
  drm/i915: use hsw rps tuning values everywhere on gen6+
  drm/radeon: split ATRM support out from the ATPX handler (v3)
  drm/radeon: convert radeon vfct code to use acpi_get_table_with_size
  ACPI: export symbol acpi_get_table_with_size
  drm/radeon: implement ACPI VFCT vbios fetch (v3)
  drm/radeon/kms: extend the Fujitsu D3003-S2 board connector quirk to cover later silicon stepping
  drm/radeon: fix checking of MSAA renderbuffers on r600-r700
  drm/radeon: allow CMASK and FMASK in the CS checker on r600-r700
  drm/radeon: init lockup timeout on ring init
  drm/radeon: avoid turning off spread spectrum for used pll
  drm/i915: fall back to bit-banging if GMBUS fails in CRT EDID reads
  drm/i915: extract connector update from intel_ddc_get_modes() for reuse
  drm/i915: fix hsw uncached pte
  ...

Pull SCSI target fixes from Nicholas Bellinger:
 "The executive summary includes:

   - Post-merge review comments for tcm_vhost (MST + nab)
   - Avoid debugging overhead when not debugging for tcm-fc(FCoE) (MDR)
   - Fix NULL pointer dereference bug on alloc_page failulre (Yi Zou)
   - Fix REPORT_LUNs regression bug with pSCSI export (AlexE + nab)
   - Fix regression bug with handling of zero-length data CDBs (nab)
   - Fix vhost_scsi_target structure alignment (MST)

  Thanks again to everyone who contributed a bugfix patch, gave review
  feedback on tcm_vhost code, and/or reported a bug during their own
  testing over the last weeks.

  There is one other outstanding bug reported by Roland recently related
  to SCSI transfer length overflow handling, for which the current
  proposed bugfix has been left in queue pending further testing with
  other non iscsi-target based fabric drivers.

  As the patch is verified with loopback (local SGL memory from SCSI
  LLD) + tcm_qla2xxx (TCM allocated SGL memory mapped to PCI HW) fabric
  ports, it will be included into the next 3.6-rc-fixes PULL request."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Remove unused se_cmd.cmd_spdtl
  tcm_fc: rcu_deref outside rcu lock/unlock section
  tcm_vhost: Fix vhost_scsi_target structure alignment
  target: Fix regression bug with handling of zero-length data CDBs
  target/pscsi: Fix bug with REPORT_LUNs handling for SCSI passthrough
  tcm_vhost: Change vhost_scsi_target->vhost_wwpn to char *
  target: fix NULL pointer dereference bug alloc_page() fails to get memory
  tcm_fc: Avoid debug overhead when not debugging
  tcm_vhost: Post-merge review changes requested by MST
  tcm_vhost: Fix incorrect IS_ERR() usage in vhost_scsi_map_iov_to_sgl

Pull i2c-embedded fixes from Wolfram Sang:
 "Some bugfixes for the "embedded" part of the I2C subsystem.  The fixes
  affect mostly drivers which have been largely reworked lately and
  where regressions appeared."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: tegra: protect suspend/resume callbacks with CONFIG_PM_SLEEP
  i2c: diolan-u2c: Fix master_xfer return code
  I2C: OMAP: xfer: fix runtime PM get/put balance on error
  i2c: nomadik: Add default configuration into the Nomadik I2C driver