WARNING: Block comments use a trailing */ on a separate line
+                        * not be accessed from here */

WARNING: Block comments use a trailing */ on a separate line
+                        * not be accessed from here */

WARNING: Block comments use a trailing */ on a separate line
+                                * the output is wanted in any case */

WARNING: Consecutive strings are generally better as a single string
+               "  addr=0x%08X, mask=0x%X, shift=%d" "value=0x%X\n",

total: 0 errors, 4 warnings, 3331 lines checked

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

WARNING: Block comments use a trailing */ on a separate line
+        * */

WARNING: Block comments use a trailing */ on a separate line
+        * bank on higher 8 bits and reg in lower */

WARNING: Block comments use a trailing */ on a separate line
+        * bank on higher 8 bits and reg in lower */

WARNING: suspect code indent for conditional statements (8, 24)
+       if (unlikely(*offset == 17))
+                       *offset = 24;

WARNING: suspect code indent for conditional statements (8, 24)
+       if (unlikely(*offset == 16))
+                       *offset = 25;

WARNING: suspect code indent for conditional statements (8, 24)
+       if ((i == 3) && (*offset >= 24))
+                       *offset += 2;

WARNING: ENOSYS means 'invalid syscall nr' and nothing else
+               return -ENOSYS;

WARNING: static const char * array should probably be static const char * const
+       static const char *switch_off_status[] = {

WARNING: static const char * array should probably be static const char * const
+       static const char *turn_on_status[] = {

total: 0 errors, 9 warnings, 1867 lines checked

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

WARNING: Possible unnecessary 'out of memory' message
+       if (!otp) {
+               dev_err(&pdev->dev, "could not allocate AB3100 OTP device\n");

total: 0 errors, 1 warnings, 250 lines checked

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

WARNING: Missing a blank line after declarations
+       struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
+       if (!ab3100->startup_events_read)

WARNING: Possible unnecessary 'out of memory' message
+       if (!ab3100) {
+               dev_err(&client->dev, "could not allocate AB3100 device\n");

WARNING: else is not generally useful after a break or return
+                               break;
+                       } else {

total: 0 errors, 3 warnings, 996 lines checked

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

WARNING: Possible unnecessary 'out of memory' message
+       if (!aat2870) {
+               dev_err(&client->dev,

total: 0 errors, 1 warnings, 524 lines checked
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Checkpatch output:

WARNING: Block comments use a trailing */ on a separate line
+        * - turn off */

WARNING: Missing a blank line after declarations
+       int ret;
+       ret = i2c_add_driver(&pm860x_driver);

total: 0 errors, 2 warnings, 1283 lines checked
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Specify the device tree binding for the input clocks to Arizona devices.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NGeliang Tang <geliangtang@163.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The mfd/s2mpa01.txt duplicates some of the information about bindings
with old mfd/s2mps11.txt. Now common part exists entirely in
mfd/samsung,sec-core.txt so:
 - add company prefix to file name (regulator/samsung,s2mpa01.txt),
 - remove duplicated information,
 - reorganize the contents to match style of
   regulator/samsung,s2mps11.txt.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The regulator/s5m8767-regulator.txt duplicates some of the information
about bindings with old mfd/s2mps11.txt. Now common part exists entirely
in mfd/samsung,sec-core.txt so:
 - add company prefix to file name (regulator/samsung,s5m8767.txt),
 - remove duplicated information,
 - reorganize the contents to match style of
   regulator/samsung,s2mps11.txt.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Bindings for Samsung S2M and S5M family PMICs are in mess. They are
spread over different files and subdirectories in a non-consistent way.
The devices and respective drivers for them share a lot in common so
everything could be organized in a more readable way.

Reorganize the S2MPS11/13/14/15 Device Tree bindings to match the
drivers for this family of devices:
 - move mfd/s2mps11.txt to mfd/samsung,sec-core.txt for the main MFD
   driver (common for entire family),
 - split clock block to clock/samsung,s2mps11.txt,
 - split regulator block to regulator/samsung,s2mps11.txt.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NMichael Turquette <mturquette@baylibre.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

This also start to propagate the negative error code from the
smbus call if there is one, as the last commit of this series
will make the gpiolib core deal with that properly.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Update the device tree binding documentation to include the wlf,out-mono
property that is used to specify whether each output is a mono or stereo
output.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add device tree bindings to support specifying outputs from the chip as
mono outputs. Whilst we are doing it change the out_mono pdata from a
bool to an int, because Sparse gets upset about using ARRAY_SIZE on
bools.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Allow support for the DA9063 PMIC to be modular, cfr. DA9062, which
allows to decrease size of multi-platform kernels (e.g.
multi_v7_defconfig).
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Currently the driver requests the boot done and control interface IRQs
before it has requested its own IRQ line. This can cause problems on
edge triggered IRQ systems as if an edge occurs before the parent IRQ is
enabled it will be missed. Whilst we are changing the error handling
remove an unused label as well.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The CS47L24 and WM1831 codecs only have two GPIO lines, but are
otherwise similar to the WM8280.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The newly introduced as3722_i2c_suspend/resume functions are built
unconditionally, but only used when power management is enabled,
so we get a warning otherwise:

drivers/mfd/as3722.c:427:12: warning: 'as3722_i2c_suspend' defined but not used [-Wunused-function]
drivers/mfd/as3722.c:438:12: warning: 'as3722_i2c_resume' defined but not used [-Wunused-function]

This marks them both as __maybe_unused, which avoids an ugly #ifdef
and gives us best compile-time coverage. When they are unused, the
compiler will silently drop the functions from its output.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 35deff7e ("mfd: as3722: Handle interrupts on suspend")
Signed-off-by: NLee Jones <lee.jones@linaro.org>

These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Revision ID registers are available only on devices with
Slave IDs that are even, so don't make access to unavailable
registers.
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
[sboyd@codeaurora.org: Consider all slave ids that are even]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

wm831x_unique_id_show currently displays an interesting pattern of '0'
and '3' characters which isn't very useful (figuring out why is left
as an exercise for the reader). Presumably "buf[i]" should have been
"id[i] & 0xff".

But while there, it is much simpler to simply use %phN and do all the
formatting at once.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Currently syscon has a fixed configuration of 32 bits for register and
values widths. In some cases, it would be desirable to be able to
customize the value width.

For example, certain boards (like the ones manufactured by Technologic
Systems) have a FPGA that is memory-mapped, but its registers are only
16-bit wide.

This patch adds an optional "reg-io-width" DT binding for syscon that
allows to change the width for the data bus (i.e. val_bits). If this
property is provided, it will also set the register stride to
reg-io-width's value. If not provided, the default configuration is
used.
Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

cros_ec_cmd_xfer_spi and cros_ec_pkt_xfer_spi generally work like
this:
 - Pull CS down (active), wait a bit, then send a command
 - Wait for response (multiple requests)
 - Wait a while, pull CS up (inactive)

These operations, individually, lock the SPI bus, but there is
nothing preventing the SPI framework from interleaving messages
intended for other devices as the bus is unlocked in between.

This is a problem as the EC expects CS to be held low for the
whole duration.

Solution: Lock the SPI bus during the whole transaction, to make
sure that no other messages can be interleaved.
Signed-off-by: NNicolas Boichat <drinkcat@chromium.org>
Reviewed-by: NGwendal Grignou <gwendal@chromium.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The CS47L24 source is part of the ex-Wolfson "Arizona" group of
drivers. Not all cs47lxx devices are part of the Arizona driver
group so the cs47l24 is explicitly listed by its full part number.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the regmap configuration tables and
core MFD handling for the CS47L24 and WM1831 codecs.

Note that compared to the other Arizona codecs, these devices
do not have an LDO1 or micsupp regulators, extcon driver, or
the DCVDD isolation control.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This updates the Arizona MFD device tree bindings to add the
Cirrus Logic CS47L24 and WM1831 codecs. Note that unlike all the
other codecs the DCVDD-supply and MICVDD-supply are mandatory.
Signed-off-by: NRichard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Signed-off-by: NLABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The platforms that use the AB8500 define all IRQ resources in the
device tree and they are automatically populated by matching
the .of_compatible string. These static resources are just
surplus baggage these days.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The da903x_chip_ops structure is never modified, so declare it
as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

For checking if a property is present or not,
use of_property_read_bool instead of of_get_property()
Signed-off-by: NSaurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The as3722 device is registered as an irqchip and the as3722-rtc interrupt
is one of it's interrupt sources. When using the as3722-rtc as a wake-up
device from suspend, the following is seen:

  PM: Syncing filesystems ... done.
  Freezing user space processes ... (elapsed 0.001 seconds) done.
  Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
  Suspending console(s) (use no_console_suspend to debug)
  PM: suspend of devices complete after 161.119 msecs
  PM: late suspend of devices complete after 1.048 msecs
  PM: noirq suspend of devices complete after 0.756 msecs
  Disabling non-boot CPUs ...
  CPU1: shutdown
  CPU2: shutdown
  CPU3: shutdown
  Entering suspend state LP1
  Enabling non-boot CPUs ...
  CPU1 is up
  CPU2 is up
  CPU3 is up
  PM: noirq resume of devices complete after 0.487 msecs
  as3722 4-0040: Failed to read IRQ status: -16
  as3722 4-0040: Failed to read IRQ status: -16
  as3722 4-0040: Failed to read IRQ status: -16
  as3722 4-0040: Failed to read IRQ status: -16
  ...

The reason why the as3722 interrupt status cannot be read is because the
as3722 interrupt is not masked during suspend and when the as3722-rtc
interrupt occurs, to wake-up the device, the interrupt is seen before the
i2c controller has been resumed in order to read the as3722 interrupt
status.

The as3722-rtc driver sets it's interrupt as a wake-up source during
suspend, which gets propagated to the parent as3722 interrupt. However,
the as3722-rtc driver cannot disable it's interrupt during suspend
otherwise we would never be woken up and so the as3722 must disable it's
interrupt instead.

Fix this by disabling the as3722 interrupt during suspend. To ensure that
a wake-up event from the as3722 is not missing, enable the as3722 interrupt
as a wake-up source before disabling the interrupt on entering suspend.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The MFD part of wm8994 consists of three files wm8994-core.c,
wm8994-irq.c and wm8994-regmap.c only wm8994-core.c has a
MODULE_DESCRIPTION / LICENSE. These were clearly intended to be built
as a single module, but currently are not. This will lead to a tainted
kernel when loading modules for wm8894-irq.c and wm8994-regmap.c because
are missing a license.

This patch fixes this issue by grouping the three files together into a
single module.
Reported-by: NPeter Robinson <pbrobinson@gmail.com>
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Fix the incorrect interrupt documentation file path in binding docs.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Currently S2MPSXX multifunction device is named as *-pmic,
and these MFDs also supports regulator as a one of its MFD cell which
has the same name, because current name is confusing and we want to
sort it out.

We did discussed different approaches about how the MFD and it
cells need to be named here [1].
Based in the discussion this patch rename MFD regulator name as
*-regulator instead of current *-pmic.

This patch also changes the corresponding entries in the regulator driver
to keep git-bisect happy.

[1]-> https://lkml.org/lkml/2015/10/28/417Suggested-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>