After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch implements the workaround mentioned in ERR005829:

    ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
    be transmitted in a specific moment during the arbitration process.

Workaround: The workaround consists of two extra steps after setting up a
message for transmission:

Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.

Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: NDavid Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.

This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: NDavid Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NStephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: NJay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Reported by Nikolay Aleksandrov.  In efx_init_port() we call
 efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls
 efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this
 lock is uninitialised, because we haven't called register_netdevice() yet.
So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before
 doing anything else.
The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the
 corresponding check.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Tested-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().

Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 35b1de55 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is
exposed through PCI Passthrough") moved the code to check for SR-IOV PF[0..3]
much further down in init_one() past the point where we allocate a (struct
adapter) for PF[0..3]. As a result, we left four of these on ever module remove.

Fix: Allocate adapter structure only for PF4
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The KSZ9031 appears to suffer from the same hardware bug as described
for the KSZ9021 in commit 32fcafbc
("net/phy: micrel: Disable asymmetric pause for KSZ9021")
you have to unplug the cable and plug it back to get it to work.

Remove the SUPPORTED_Asym_Pause flag for the KSZ9031 to fix this.
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem is that the slave is first linked and slave_cnt is
incremented afterwards leading to a div by zero in the modes that use it
as a modulus. What happens is that in bond_start_xmit()
bond_has_slaves() is used to evaluate further transmission and it becomes
true after the slave is linked in, but when slave_cnt is used in the xmit
path it is still 0, so fetch it once and transmit based on that. Since
it is used only in round-robin and XOR modes, the fix is only for them.
Thanks to Eric Dumazet for pointing out the fault in my first try to fix
this.

Call trace (took it out of net-next kernel, but it's the same with net):
[46934.330038] divide error: 0000 [#1] SMP
[46934.330041] Modules linked in: bonding(O) 9p fscache
snd_hda_codec_generic crct10dif_pclmul
[46934.330041] bond0: Enslaving eth1 as an active interface with an up
link
[46934.330051]  ppdev joydev crc32_pclmul crc32c_intel 9pnet_virtio
ghash_clmulni_intel snd_hda_intel 9pnet snd_hda_controller parport_pc
serio_raw pcspkr snd_hda_codec parport virtio_balloon virtio_console
snd_hwdep snd_pcm pvpanic i2c_piix4 snd_timer i2ccore snd soundcore
virtio_blk virtio_net virtio_pci virtio_ring virtio ata_generic
pata_acpi floppy [last unloaded: bonding]
[46934.330053] CPU: 1 PID: 3382 Comm: ping Tainted: G           O
3.17.0-rc4+ #27
[46934.330053] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[46934.330054] task: ffff88005aebf2c0 ti: ffff88005b728000 task.ti:
ffff88005b728000
[46934.330059] RIP: 0010:[<ffffffffa0198c33>]  [<ffffffffa0198c33>]
bond_start_xmit+0x1c3/0x450 [bonding]
[46934.330060] RSP: 0018:ffff88005b72b7f8  EFLAGS: 00010246
[46934.330060] RAX: 0000000000000679 RBX: ffff88004b077000 RCX:
000000000000002a
[46934.330061] RDX: 0000000000000000 RSI: ffff88004b3f0500 RDI:
ffff88004b077940
[46934.330061] RBP: ffff88005b72b830 R08: 00000000000000c0 R09:
ffff88004a83e000
[46934.330062] R10: 000000000000ffff R11: ffff88004b1f12c0 R12:
ffff88004b3f0500
[46934.330062] R13: ffff88004b3f0500 R14: 000000000000002a R15:
ffff88004b077940
[46934.330063] FS:  00007fbd91a4c740(0000) GS:ffff88005f080000(0000)
knlGS:0000000000000000
[46934.330064] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[46934.330064] CR2: 00007f803a8bb000 CR3: 000000004b2c9000 CR4:
00000000000406e0
[46934.330069] Stack:
[46934.330071]  ffffffff811e6169 00000000e772fa05 ffff88004b077000
ffff88004b3f0500
[46934.330072]  ffffffff81d17d18 000000000000002a 0000000000000000
ffff88005b72b8a0
[46934.330073]  ffffffff81620108 ffffffff8161fe0e ffff88005b72b8c4
ffff88005b302000
[46934.330073] Call Trace:
[46934.330077]  [<ffffffff811e6169>] ?
__kmalloc_node_track_caller+0x119/0x300
[46934.330084]  [<ffffffff81620108>] dev_hard_start_xmit+0x188/0x410
[46934.330086]  [<ffffffff8161fe0e>] ? harmonize_features+0x2e/0x90
[46934.330088]  [<ffffffff81620b06>] __dev_queue_xmit+0x456/0x590
[46934.330089]  [<ffffffff81620c50>] dev_queue_xmit+0x10/0x20
[46934.330090]  [<ffffffff8168f022>] arp_xmit+0x22/0x60
[46934.330091]  [<ffffffff8168f090>] arp_send.part.16+0x30/0x40
[46934.330092]  [<ffffffff8168f1e5>] arp_solicit+0x115/0x2b0
[46934.330094]  [<ffffffff8160b5d7>] ? copy_skb_header+0x17/0xa0
[46934.330096]  [<ffffffff8162875a>] neigh_probe+0x4a/0x70
[46934.330097]  [<ffffffff8162979c>] __neigh_event_send+0xac/0x230
[46934.330098]  [<ffffffff8162a00b>] neigh_resolve_output+0x13b/0x220
[46934.330100]  [<ffffffff8165f120>] ? ip_forward_options+0x1c0/0x1c0
[46934.330101]  [<ffffffff81660478>] ip_finish_output+0x1f8/0x860
[46934.330102]  [<ffffffff81661f08>] ip_output+0x58/0x90
[46934.330103]  [<ffffffff81661602>] ? __ip_local_out+0xa2/0xb0
[46934.330104]  [<ffffffff81661640>] ip_local_out_sk+0x30/0x40
[46934.330105]  [<ffffffff81662a66>] ip_send_skb+0x16/0x50
[46934.330106]  [<ffffffff81662ad3>] ip_push_pending_frames+0x33/0x40
[46934.330107]  [<ffffffff8168854c>] raw_sendmsg+0x88c/0xa30
[46934.330110]  [<ffffffff81612b31>] ? skb_recv_datagram+0x41/0x60
[46934.330111]  [<ffffffff816875a9>] ? raw_recvmsg+0xa9/0x1f0
[46934.330113]  [<ffffffff816978d4>] inet_sendmsg+0x74/0xc0
[46934.330114]  [<ffffffff81697a9b>] ? inet_recvmsg+0x8b/0xb0
[46934.330115] bond0: Adding slave eth2
[46934.330116]  [<ffffffff8160357c>] sock_sendmsg+0x9c/0xe0
[46934.330118]  [<ffffffff81603248>] ?
move_addr_to_kernel.part.20+0x28/0x80
[46934.330121]  [<ffffffff811b4477>] ? might_fault+0x47/0x50
[46934.330122]  [<ffffffff816039b9>] ___sys_sendmsg+0x3a9/0x3c0
[46934.330125]  [<ffffffff8144a14a>] ? n_tty_write+0x3aa/0x530
[46934.330127]  [<ffffffff810d1ae4>] ? __wake_up+0x44/0x50
[46934.330129]  [<ffffffff81242b38>] ? fsnotify+0x238/0x310
[46934.330130]  [<ffffffff816048a1>] __sys_sendmsg+0x51/0x90
[46934.330131]  [<ffffffff816048f2>] SyS_sendmsg+0x12/0x20
[46934.330134]  [<ffffffff81738b29>] system_call_fastpath+0x16/0x1b
[46934.330144] Code: 48 8b 10 4c 89 ee 4c 89 ff e8 aa bc ff ff 31 c0 e9
1a ff ff ff 0f 1f 00 4c 89 ee 4c 89 ff e8 65 fb ff ff 31 d2 4c 89 ee 4c
89 ff <f7> b3 64 09 00 00 e8 02 bd ff ff 31 c0 e9 f2 fe ff ff 0f 1f 00
[46934.330146] RIP  [<ffffffffa0198c33>] bond_start_xmit+0x1c3/0x450
[bonding]
[46934.330146]  RSP <ffff88005b72b7f8>

CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
Fixes: 278b2083 ("bonding: initial RCU conversion")
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The setting should depend on the new features not the current one.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the parameter "features" of __rtl8169_set_features() is equal to
dev->features, the variable "changed" is alwayes 0, and nothing would
be changed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During suspend and resume in Dual EMAC, second port is not working as in
suspend/resume only the first slave netdev is closed and opened. So bring
down and up all the interfaces that are up during suspend/resume.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nstat->multicast refers to received packets, not transmitted as
is returned here. Change it so that received packet stats are
given.
Signed-off-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.

This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.

The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 09ebb810.

ath9k_hw_set_sta_beacon_timers() configures AR_TIM_PERIOD with
the beacon interval. Before this commit, the sleepduration was
never greater than the beacon interval. But now, the behavior
has changed. For example, with an AP that uses a beacon interval of 100:

ath: phy9: next beacon 61128704
ath: phy9: beacon period 204800
ath: phy9: DTIM period 204800

If the sleepduration is calculated based on the listen time, then
the bmiss threshold should also be changed since the HW would
be in sleep state for a longer time, but that is not done currently.

To avoid configuring a higher beacon interval based on the sleepduration,
revert to the original behavior. Power consumption is not a
problem since PS is disabled in ath9k anyway.

Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apparently can_restart() runs from a (timer-) interrupt and can call
flexcan_chip_[en|dis]able(), so avoid using usleep_range()
Signed-off-by: NDavid Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.

Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.

Fixes: 7677fc96 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current wrapper implementation of the UPDATE_QP command tries to get
the MAC index, even if MAC wasn't set by the VF. Fix it up to only handle
the MAC field if it's valid.

Fixes: ce8d9e0d ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing VGT->VST->VGT state changes, we used an incorrect mask
for the vlan-stripping-disable (VSD) flag, hence the vlan related policy
for user-space Raw Ethernet QPs open by VFs wasn't really applied.

Fix that, by using the correct mask.

Fixes: f0f829bf ('net/mlx4_core: Add immediate activate for VGT->VST->VGT')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Single port VFs are seen PCI wise on both ports of the PF (we don't have
single port PFs with ConnectX). With this in mind, it's possible for
virtualization tools to try and configure a single ported VF through
the "wrong" PF port.

To handle that, we use the PF driver mapping of single port VFs to NIC
ports and adjust the port value before calling into the low level
code that does the actual VF configuration

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Dual EMAC, when both interface are up and while doing ifdown with heavy
traffic then skbs already processed by DMA from that slave emac has to be
requeued as still the other interface is up and running.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds missing space between "interface" and "by"
in bonding module parameter description.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.

The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.

Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.

The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.

Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver does not support pause autonegotiation so it should return
-EINVAL when the function is called with non-zero autoneg.

Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following compiler warning:

drivers/net/ethernet/octeon/octeon_mgmt.c: In function 'octeon_mgmt_clean_tx_buffers':
drivers/net/ethernet/octeon/octeon_mgmt.c:295:4: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
    u64 ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port));
    ^
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sunvnet driver does not have an rmb() in the ring consumer corresponding
to the wmb() in the producer. According to Documentation/memory-barriers.txt:

"When dealing with CPU-CPU interactions, certain types of memory barrier should
always be paired.  A lack of appropriate pairing is almost certainly an error."

In cases where an rmb() is not a no-op and a consumer is removing data from
the ring while a producer is adding new entries, a load reorder would allow

CPU1						CPU2
----						----
						LOAD desc.size [e.g]
STORE desc.size
<wmb>
set desc.hdr.state = VIO_DESC_READY
						LOAD desc.hdr.state
						[because VIO_DESC_READY, use
						 old desc.size, already loaded
						 out of order]

[CPU2 has reordered apparently unrelated LOADs]

To ensure other desc fields are not loaded before checking VIO_DESC_READY, we
need an rmb() between the check and desc data accesses.

I've also moved the viodbg() call to after the rmb() so that it, too, has
current descriptor data even with reordering, which has the side effect that
it won't print anything for descriptors that are not VIO_DESC_READY as before.
That's a) probably a good thing, since the fields are not necessarily set and,
b) better than adding another rmb() just for viodbg().

This would not be possible if strict-ordering is enforced, but then the
memory barriers should be no-ops in that case.
Signed-off-by: NDavid L Stevens <david.stevens@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The idea here is to translate a value of 0 received from
the firmware to the lowest rssi figure. As rx_status->chain_signal
is a signed byte the lowest possible value is -128 and not -256.
-256 was causing 0 to get stored in the signed byte.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This change does the following:
1) Add a new 7265 series PCI ID
2) Add two new 3160 series PCI IDs
3) Add the new 3165 series PCI IDs and configurations
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In
https://bugzilla.kernel.org/show_bug.cgi?id=84031,
the submitter said that disabling power saving helped,
do just that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

smps_mode is used uninitialized in a debug statement in AP
mode, so always initialize it.

While at it, fix a typo.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The latter is meant for software implementation of power
save and is not per-virtual interface. Since our driver
supports multiple virtual interfaces, we need to use
vif->bss_conf.dtim_period.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Using the LQ table which is initially set according to
the rssi could lead to EAPOLs being sent in high legacy
rates like 54mbps.
It's better to avoid sending EAPOLs in high rates as it reduces
the chances of a successful 4-Way handshake.
Avoid this and treat them like other mgmt frames which would
initially get sent at the basic rate.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When mac80211 requests multiple BSS config changes, as for example
while associating, we ignore power management and QoS changes and
only apply them later. Fix that by removing the "else" and making
the conditions independent.

Also move it after (potential) beacon filter enablement to have
that already enabled when going into power management code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The chip is able to transmit up to 22dBm, so set
the constant appropriately.

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This code was broken on big endian systems. Sparse didn't
catch the bug since the firmware command was not tagged as
little endian.
Fix the bug for big endian systems and tag the field in the
firmware command to prevent such issues in the future.

Cc: stable@vger.kernel.org [3.14+]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In commit cad3f08c (iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when
forced_assoc_off is set) the code to set the MAC_FILTER_IN_BEACON flag
was accidentally moved to the main block of the if statement, while it
should be in the else block instead.  Move it to the right place.

Fixes: cad3f08c ("iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when forced_assoc_off is set")
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>