Once more, with feeling: not all VSIs have rings. To assume so is to
invite null pointers to your party.

Change-ID: I576858824468d9712d119fa1015a1f28c27712c4
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Be sure to clear PXE mode bit on each reset after AdminQ has been rebuilt.

Change-ID: I992d8c79594f8ca0660c50844ace675ecb9c9bf2
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes an issue where FD SB/ATR and NTUPLE configurations status are
reported erroneously. Without this patch, driver reports FDir without further
information.

Change-ID: I5bdd2871b7f2db1e5f5e76c741ae6a0dc603b453
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The correct format is %pM, not %pMAC.

Change-ID: Idb335723a966fe56db3a72b9c07c08ca66f9db3c
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up inconsistent log messages, mostly related to punctuation. Based
on the dogma that "kernel messages are not sentences", remove all
trailing periods. Reword a few of the messages to make them less
sentence-like.

Change-ID: Ibd849aa7623a77549b0709988c66ab05d1311472
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This comment is just plain false. VF drivers require MSI-X or they won't
get interrupts at all.

Change-ID: Iaea5e30b6926948aa834a3c506d9a9223d9e3e29
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need to print log messages when we encounter an out-of-memory
condition, as the allocator will do this for us. Also, remove a Tx hang
message that duplicates the one emitted by the netdev layer, and a
duplicate message in the watchdog.

Change-ID: If2056e6135fe248f66ea939778f9895660f4d189
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1. There is no ixgbe_watchdog_task function in the driver, so change
   the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
   because it is never used.
3. Remove some TBD comments that are not needed.

Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove use of registers no longer supported.

Change-ID: I9d27399091cea78a926489d94f958edd762f5a20
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As reported by Eric Dumazet, the driver is not masking the right
bits in the receive descriptor before it starts checking them.

This patch extends the mask to allow for the right bits to be
checked, and fixes the issue permanently via a define.

CC: Eric Dumazet <eric.dumazet@gmail.com>
Change-ID: I3274f7619057a950f468143e6d7e11b129f54655
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During key removal, the key object is freed, but not taken out of the
llsec key list properly. Fix that.
Signed-off-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The include of asm/cputype.h breaks the powerpc build. This
include was accidentally left in from driver debugging and
can be removed.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>,
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-06-06

This series contains updates to i40e and i40evf.

Shannon sets the lan_veb index when the Virtual Ethernet Bridge (VEB) is
created for the basic LAN device and its Virtual Switch Interfaces (VSIs).
Also adds the VEB/VSI statistics in the ethtool stats output.  Increases the
reset wait time because the original time was too optimistic and resets
were failing after EMPR.  This won't delay the actual wait, just allows
us to poll more times as needed.  He fixes the attempted removal of the
HMC space and unhook IRQs when a reset recovery fails because the HMC space
never got setup and IRQs are already unhooked in the first place, so the
removal is not necessary.

Jesse adds a log message for pre-production hardware so that the user is
notified that there may be issues with the hardware, yet does not prevent
the user from using the hardware.  Add the printing of link messages
in the i40e driver like all the other Intel Ethernet drivers.

Mitch makes log message changes to i40evf to prevent confusion by making
the most common messages less scary by lowering them to a less terrifying
log level.  This is due to the fact that depending on the timing of what
the PF driver is doing, it may take a few tries before the VF driver is able
to communicate with the PF driver on init or reset recovery.

Kamil provides a change to prevent the driver from getting into a endless
loop while trying to send GetVersion AQ command, since BO silicon blocks
AQ registers when in Blank Flash mode.  So introduce a simple check for a
correct value in one of the AQ registers to be sure that AQ was configured
correctly.

Matt adds a function which indicates our intention to enable or disable a
particular transmit queue.  Also adds a function to notify the device's
transmit unit that we are about to enable or disable a transmit queue.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump i40e to 0.4.3 and i40evf to 0.9.27.

Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use an extra state variable to keep track of when the IRQs are fully
set up.  This keeps us from trying to unhook IRQs that already were
left unhooked in a failed reset recovery, e.g. when firmware is broken.

Change-ID: I073eb081e4ef8aedcbdf1ee0717c0ed64fa172f2
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a reset recovery failed (e.g. firmware is broken), the HMC space won't
get set up.  We don't need to try to delete it if it didn't get set up.
This stops some needless error messages when we already know we need to
just tear things down.

Change-ID: Iac600481765e20b136052b43a544e55d7870268b
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e driver should print link messages like all the
other Intel Ethernet drivers.

Change-ID: Ia88bdb96794e17a3962fcea94db176de01f921f7
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the missing unicast, multicast, and broadcast stats for the port.

Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add VSI HW stats for unicast, multicast, and broadcast for Rx and Tx.
Stop printing the netdev multicast value because it doesn't include Tx
and would be confusing.

Change-ID: I08278b6657e7c838fd29a4a1f305f78fe1b150be
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The wait time was originally too optimistic and the resets were failing
after EMPR.  This increases the loop count to wait considerably longer.
This won't delay the actual wait longer than really needed, just allows
us to poll more times as needed.

Change-ID: If7b96f55cc25b8d06cbbe8665259d250188c53d7
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.

Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: NMatt Jared <matthew.a.jared@intel.com>
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.

Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.

Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver and hardware are not expected to work correctly
with revision_id 0 hardware.  Don't prevent the user from
using it, but be sure to print a warning.

Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Print the VEB statistics in the ethtool stats output.

Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.

Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To avoid the confusion of having two variables, shrink the function to
only use the parameter variable for looping.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NSven Wegener <sven.wegener@stealer.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/xen-netback/netback.c
	net/core/filter.c

A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.

A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BPF classic->internal converter broke SKF_AD_PKTTYPE extension, since
pkt_type_offset() was failing to find skb->pkt_type field which is defined as:
__u8 pkt_type:3,
     fclone:2,
     ipvs_property:1,
     peeked:1,
     nf_trace:1;

Fix it by searching for 3 most significant bits and shift them by 5 at run-time

Fixes: bd4cf0ed ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Tested-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes the following sparse warning:

drivers/net/phy/fixed.c:207
    - warning: symbol 'fixed_phy_del' was not declared.
      Should it be static?

by adding symbol definition to the phy_fixed.h API file. It is ok to do
because the function in question is an exported symbol.
Signed-off-by: NKonrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: misc fixes

This patch series contains some misc fixes for the SYSTEMPORT driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/nf_tables fixes for net-next

This patchset contains fixes for recent updates available in your
net-next, they are:

1) Fix double memory allocation for accounting objects that results
   in a leak, this slipped through with the new quota extension,
   patch from Mathieu Poirier.

2) Fix broken ordering when adding set element transactions.

3) Make sure that objects are released in reverse order in the abort
   path, to avoid possible use-after-free when accessing dependencies.

4) Allow to delete several objects (as long as dependencies are
   fulfilled) by using one batch. This includes changes in the use
   counter semantics of the nf_tables objects.

5) Fix illegal sleeping allocation from rcu callback.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD 10Gb Ethernet driver

The following series implements support for the new AMD 10Gb Ethernet
driver (amd-xgbe).  It includes the 10Gb Ethernet driver as well as
a 10Gb Ethernet PHY driver.

This patch series is based on net-next.

Changes in V3:
  - Add OF dependency to the phylib driver configuration
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the maintainer information for the AMD 10GbE
platform driver.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>