Fix a spelling error, s/extention/extension/.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

    This new firmware fixes following bugs:
     1. HW attention appears and traffic stops when iSCSI firmware tries to
        retransmit iSCSI login command when the iSCSI login is carrying data
        not aligned to 4-bytes.
     2. FCoE traffic fails to run when running in switch-independent multi-function
        mode and there's more than one interface supporting FCoE on a given port.
     3. While two ports are running FCoE with at least one of them has a function
        number (>1) on the same engine in a 4-port device a zeroed CQE is given,
        causing FCoE traffic to stop.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This removes the various points where the driver use bit operations in order
to schedule the sp_rtnl_task from the code, adding a single utility function
that does it instead.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x_panic_dump() prints all kind of driver information, including slowpath
information. Since VFs don't initialize slowpath information, a VF reaching
this flow will likely cause a panic in the system as it will access NULL
pointers.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several places in IOV related flows where PF needs to determine
whether a VF slowpath elements have already been configured (i.e., this
affect its ability to configure/remove classifications for the VF).

This patch changes the conditions for the validation and performs a cleaner
validation (e.g., by replacing several validations with a single one).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This provides PF-side support for VFs assigned to a VM running windows
2012 with the RSC feature enabled.
Signed-off-by: NMichal Kalderon <michals@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is purely semantic - break the flow in which PF validates the VF
classification filtering requirement is valid into several sub-functions
for better readable code.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Latest FW performs this autonomously, makes this code surplus.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some debug prints (mostly iov/statistics related) which clobber
system logs whenever their verbosity level is set for an interface.
This patch puts harsher verbosity requirements for such debug prints to be
printed.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expose the PHY device has_fixups boolean as a sysfs property to help
troubleshooting PHY configurations.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a boolean property which indicates if the PHY has had any fixup
routine ran on it. We are later going to use that boolean to expose it
as a sysfs property to help troubleshooting.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Expose the PHY device interface mode through sysfs since this is an
useful piece of information for knowing how the attached networking
device will have configured its transmit/receive path.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

of_get_phy_mode() uses a local array to map phy_interface_t values from
include/linux/net/phy.h to a string which is read from the 'phy-mode' or
'phy-connection-type' property. In preparation for exposing the PHY
interface mode through sysfs, perform the following:

- mode phy_modes from drivers/of/of_net.c to include/linux/phy.h such
  that it is right below the phy_interface_t enum
- make it a static inline function returning the string such that we can
  use it by just including include/linux/net/phy.h
- add a PHY_INTERFACE_MODE_MAX enum value to guard the iteration in
  of_get_phy_mode()
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The comments above phy_{clear,config}_interrupt used the word "on"
instead of "or", when talking about the return values of the functions,
fix these two typos.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHYs out there can be very quirky with respect to how they would
report the auto-negotiation is completed. Allow drivers to override the
generic aneg_done() implementation by providing their own.

Since not all drivers have been updated yet to use genphy_aneg_done() as
aneg_done() callback, we explicitely check that this callback is valid
before calling into it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for allowing PHY drivers to potentially override their
auto-negotiation done callback, move the contents of phy_aneg_done() to
genphy_aneg_done() since that function really is the generic
implementation based on the BMSR_ANEGCOMPLETE status.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a convenience function: phy_speed_to_str() which will display human
readable speeds.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update phy_print_status() to also display the PHY device pause settings
(rx/tx or off).
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_print_status() currently uses dev_name(&phydev->dev) which will
usually result in printing something along those lines for Device Tree
aware drivers:

libphy: f0b60000.etherne:0a - Link is Down
libphy: f0ba0000.etherne:00 - Link is Up - 1000/Full

This is not terribly useful for network administrators or users since we
expect a network interface name to be able to correlate link events with
interfaces. Update phy_print_status() to use netdev_info() with
phydev->attached_dev which is the backing network device for our PHY
device. The leading dash is removed since netdev_info() prefixes the
messages with "<interface>: " already.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove trailing blank lines in several files.
Use only one blank line between functions.
Add a blank line as a separator in a few places.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't use 'Solarstorm' or 'Solarflare Communications' in full
any more.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Functions such as is_valid_ether_addr() expect u8 *, so use that
instead of char *.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We allocate efx_channel structures with kzalloc() so we don't need to
zero-initialise individual fields in efx_probe_channel().  Further,
this function will be called again during DMA ring resizing and we
should not reset any statistics then.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EF10 implements option descriptors to switch TX checksum offload
on and off between packets.  We could therefore use a single
hardware TX queue per kernel TX queue, although we don't yet.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These DMA descriptor types will only be used by the userland
networking stack.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined then NET_IP_ALIGN
will be defined as 0, so this macro is redundant.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is substantial latency in generation and handling of PPS events
from the NIC, which we have to correct for before passing a host
timestamp to the PPS subsystem.  We compare clocks with the MC,
giving us two offsets to subtract from the timestamp generated by
pps_get_ts():

(a) Time from the last good sync (where we got host and NIC timestamps
    for nearly the same instant) to the time we called pps_get_ts()
(b) Time from NIC top of second to the last good sync

We currently calculate (a) + (b) in a quite confusing way.
Instead, calculate (a) completely, then add (b) to it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use conventional net_ratelimit() instead.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: NJohn Greene <jogreene@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bond enslave processing don't hold bond->lock anymore,
so release an unlocked rw lock will cause warning message,
remove the unwanted read_unlock(&bond->lock).

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Acked-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLiu Junliang <liujunliang_ljl@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If you do

  echo 0 > /sys/module/edac_core/parameters/edac_mc_poll_msec

the following stack trace is output because the edac module is not
designed to poll with a timeout of zero.

  WARNING: CPU: 12 PID: 0 at lib/list_debug.c:33 __list_add+0xac/0xc0()
  list_add corruption. prev->next should be next (ffff8808291dd1b8), but was           (null). (prev=ffff8808286fe3f8).
  Modules linked in: sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache cfg80211 rfkill x86_pkg_temp_thermal coretemp kvm_intel kvm ixgbe e1000e crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt ptp sb_edac iTCO_vendor_support pps_core mdio ipmi_devintf edac_core ioatdma microcode shpchp lpc_ich pcspkr i2c_i801 dca mfd_core ipmi_si wmi ipmi_msghandler nfsd auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sd_mod sr_mod cdrom crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt isci i2c_algo_bit drm_kms_helper ttm drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod
  CPU: 12 PID: 0 Comm: swapper/12 Not tainted 3.13.0+ #1
  Hardware name: Intel Corporation LH Pass ........../SVRBD-ROW_T, BIOS SE5C600.86B.01.08.0003.022620131521 02/26/2013
  Call Trace:
   <IRQ>
    __list_add+0xac/0xc0
    __internal_add_timer+0xab/0x130
    internal_add_timer+0x17/0x40
    mod_timer_pinned+0xca/0x170
    intel_pstate_timer_func+0x28a/0x380
    call_timer_fn+0x36/0x100
    run_timer_softirq+0x1ff/0x2f0
    __do_softirq+0xf5/0x2e0
    irq_exit+0x10d/0x120
    smp_apic_timer_interrupt+0x45/0x60
    apic_timer_interrupt+0x6d/0x80
   <EOI>
    cpuidle_idle_call+0xb9/0x1f0
    arch_cpu_idle+0xe/0x30
    cpu_startup_entry+0x9e/0x240
    start_secondary+0x1e4/0x290

  kernel BUG at kernel/timer.c:1084!
  invalid opcode: 0000 [#1] SMP
  Modules linked in: sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache cfg80211 rfkill x86_pkg_temp_thermal coretemp kvm_intel kvm ixgbe e1000e crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt ptp sb_edac iTCO_vendor_support pps_core mdio ipmi_devintf edac_core ioatdma microcode shpchp lpc_ich pcspkr i2c_i801 dca mfd_core ipmi_si wmi ipmi_msghandler nfsd auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sd_mod sr_mod cdrom crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt isci i2c_algo_bit drm_kms_helper ttm drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod
  CPU: 12 PID: 0 Comm: swapper/12 Tainted: G        W    3.13.0+ #1
  Hardware name: Intel Corporation LH Pass ........../SVRBD-ROW_T, BIOS SE5C600.86B.01.08.0003.022620131521 02/26/2013
  Call Trace:
   <IRQ>
    run_timer_softirq+0x245/0x2f0
    __do_softirq+0xf5/0x2e0
    irq_exit+0x10d/0x120
    smp_apic_timer_interrupt+0x45/0x60
    apic_timer_interrupt+0x6d/0x80
   <EOI>
    cpuidle_idle_call+0xb9/0x1f0
    arch_cpu_idle+0xe/0x30
    cpu_startup_entry+0x9e/0x240
    start_secondary+0x1e4/0x290
  RIP   cascade+0x93/0xa0

  WARNING: CPU: 36 PID: 1154 at kernel/workqueue.c:1461 __queue_delayed_work+0xed/0x1a0()
  Modules linked in: sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache cfg80211 rfkill x86_pkg_temp_thermal coretemp kvm_intel kvm ixgbe e1000e crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt ptp sb_edac iTCO_vendor_support pps_core mdio ipmi_devintf edac_core ioatdma microcode shpchp lpc_ich pcspkr i2c_i801 dca mfd_core ipmi_si wmi ipmi_msghandler nfsd auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sd_mod sr_mod cdrom crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt isci i2c_algo_bit drm_kms_helper ttm drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod
  CPU: 36 PID: 1154 Comm: kworker/u481:3 Tainted: G        W    3.13.0+ #1
  Hardware name: Intel Corporation LH Pass ........../SVRBD-ROW_T, BIOS SE5C600.86B.01.08.0003.022620131521 02/26/2013
  Workqueue: edac-poller edac_mc_workq_function [edac_core]
  Call Trace:
    dump_stack+0x45/0x56
    warn_slowpath_common+0x7d/0xa0
    warn_slowpath_null+0x1a/0x20
    __queue_delayed_work+0xed/0x1a0
    queue_delayed_work_on+0x27/0x50
    edac_mc_workq_function+0x72/0xa0 [edac_core]
    process_one_work+0x17b/0x460
    worker_thread+0x11b/0x400
    kthread+0xd2/0xf0
    ret_from_fork+0x7c/0xb0

This patch adds a range check in the edac_mc_poll_msec code to check for 0.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

  drivers/md/bcache/extents.c: In function `btree_ptr_bad_expensive':
  drivers/md/bcache/extents.c:196: warning: format `%li' expects type `long int', but argument 4 has type `size_t'
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

i2o_cfg_compat_ioctl(I2OGETIOPS) locks i2o_cfg_mutex and then calls
i2o_cfg_ioctl(I2OGETIOPS) that locks i2o_cfg_mutex as well.  A deadlock
is guaranteed.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I was reviewing this and noticed that unlocking should be conditional on
the error path.  I've changed it to unlock and return directly since we
only do it once and it seems unlikely to change in the near future.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDimitri Sivanich <sivanich@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>