Here's what modified vectors will look like
in the /proc/interrupts

        MSIx             	INTx
-----------------------------------------
83xx    qlcnic[MB]
	qlcnic-ethX[Rx0]
	qlcnic-ethX[Rx1]
	..
	qlcnic-ethX[RxN]
	qlcnic-ethx[Tx0]        qlcnic[MB+Tx0+Rx0]

82xx    qlcnic-ethX[Rx0]
	qlcnic-ethX[Rx1]
	..
	qlcnic-ethX[Tx0+RxN]    qlcnic-ethX[Tx0+Rx0]
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable Interrupt coalescing through ethtool on 83xx adapter.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Read eSwitch statistics from adapter and display them as part
  of ethtool statistics.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Disabling PAUSE requires access to EPORT registers,
  which may cause a wedge, if EPORT is in reset.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Add logs for various failure conditions during channel configuration.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of PCIe Advanced Error Reporting flow, if a fatal PCI error occurs,
the AER driver will cause bnx2x's PCI-core to reset. The driver's PCI error
handlers will in turn restore the PCI configuration space values by calling
`pci_restore_state'.

However, as bnx2x does not save the PCI configuration after restoration,
An additional fatal PCI error will leave the function in an unstable state
until reboot, as the registers in the PCI configuration space will contain
reset values.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There exists an `allocation race' between the CNIC and bnx2x drivers,
in which both drivers allocate the same t2 memory while disregarding a possible
previous allocation.

Additionally, due to the current order of memory releases, some of the
ILT memory in the driver is not released correctly when unloading the driver.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improved support for adding/removing vf mac addresses.

This includes the case where HyperVisor forced the address (sampled from
bulletin board), and the case where it did not in which the VF can
configure its own mac address.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when link is configured to auto-negotiate the flow control,
disabling RX/TX pause via ethtool doesn't work.

This fixes the behaviour, advertising asymmetric pause in case either one
is exclusively enabled.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces a more robust error handling flow in case of incorrect
behaviour by the FW when passing on GRO aggregations.

Although this should never happen (i.e., this is merely a theoretical fix),
if the bnx2x driver was to receive a GRO from FW with protocol other than
IPv4/IPv6, the driver would falsely claim to have performed partial
checksum and set various incorrect fields in the skb header.

Current behaviour of the bnx2x driver (i.e., print an error) is insufficient.
This patch remedies this by simply preventing the false claims.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a service task to run tasks that needed to be executed periodically.
Currently the only task is a watchdog to catch NIC clock overflow, to make
timestamping accurate.
Will move the statistics task into this framework in a later patch.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the HW MAC layer. This patch adds this call.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch allows to enable/disable HW timestamping for incoming and/or
outgoing packets. It adds and initializes all structs and callbacks
needed by kernel TS API.
To enable/disable HW timestamping appropriate ioctl should be used.
Currently HWTSTAMP_FILTER_ALL/NONE and HWTSAMP_TX_ON/OFF only are
supported.
When enabling TS on receive flow - VLAN stripping will be disabled.
Also were made all relevant changes in RX/TX flows to consider TS request
and plant HW timestamps into relevant structures.
mlx4_ib was fixed to compile with new mlx4_cq_alloc() signature.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new device capability for timestamping support and query FW to retrieve it.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rotate bss prio list, so the bss next to the one served, will come first
in the list of bss' with equal priority. This way we pick bss nodes in a
round robin fashion. Using list rotation instead of a cur ptr simplifies
iteration to calling list_for_each_entry. List rotation is done via
list_move, where the head itself is temporarily removed and then
re-inserted after the bss just served.
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After a packet is successfully transmitted, ra list is rotated, so the ra
next to the one transmitted, will be the first in the list. This way we
pick the ra' in a round robin fashion. This significantly simplifies
iteration in  mwifiex_wmm_get_highest_priolist_ptr to a call to
list_for_each_entry.
List rotation is done via list_move, where the head itself is temporarily
removed and then re-inserted after the item just transferred.
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware provides credits to the driver per WMM-AC. When
only AC_BE are to be transmitted to the firmware the driver
may use credits from other priorities to send AC_BE packets
towards the firmware.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In brcmf_fws_init() the error flows were not properly handled
and the caller ignored the return value. The only action that
is allowed to fail in brcmf_fws_init() is setting the tlv in
firmware as the feature is not supported on all devices.

Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When firmware signals the driver to remove a destination entry
it may have sk_buff packets queued for it. These should be freed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds support for the critical protocol API provided by nl80211
which gives Wifi traffic priority over a Bluetooth (e)SCO connection
and disables scanning during DCHP negotiation.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During the DHCP protocol exchange it is benificial to suppress
scan requests which may decrease time to complete DHCP protocol.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After the commit "ath9k: improve dma map failure handling", the
wrong buffer was DMA-unmapped, introducing warnings like the one below.
This patch fixes the issue.

WARNING: at /home/sujith/dev/wireless-testing/lib/dma-debug.c:986 check_sync+0x4bc/0x580()
Hardware name: LIFEBOOK AH531
ath9k 0000:02:00.0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x00000000d9012800] [size=48 bytes]
Pid: 86, comm: kworker/u:5 Tainted: G        W  O 3.9.0-rc8-wl-debug #106
Call Trace:
 [<ffffffff810410c0>] warn_slowpath_common+0x70/0xa0
 [<ffffffff8104113c>] warn_slowpath_fmt+0x4c/0x50
 [<ffffffff8125432c>] check_sync+0x4bc/0x580
 [<ffffffff8109e5f7>] ? trace_hardirqs_on_caller+0xa7/0x190
 [<ffffffff8109e6ed>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff81254488>] debug_dma_sync_single_for_device+0x48/0x50
 [<ffffffffa0a53825>] ? ath9k_iowrite32+0x35/0x90 [ath9k]
 [<ffffffff812512f0>] ? swiotlb_tbl_sync_single+0x50/0x90
 [<ffffffff81251350>] ? swiotlb_sync_single+0x20/0x30
 [<ffffffff8125137f>] ? swiotlb_sync_single_for_device+0xf/0x20
 [<ffffffffa0a58baf>] ath_rx_edma_buf_link+0xef/0x140 [ath9k]
 [<ffffffffa0a58c4e>] ath_rx_addbuffer_edma+0x4e/0x90 [ath9k]
 [<ffffffffa0a59c51>] ath_startrecv+0xf1/0x120 [ath9k]
 [<ffffffffa0a550e0>] ath_complete_reset+0x20/0x130 [ath9k]
 [<ffffffffa0a5790d>] ath_reset_internal+0x10d/0x210 [ath9k]
 [<ffffffffa0a5878c>] ath9k_config+0x47c/0x7b0 [ath9k]
 [<ffffffffa06d4978>] ieee80211_hw_config+0x88/0x3f0 [mac80211]
 [<ffffffffa06d4a3f>] ? ieee80211_hw_config+0x14f/0x3f0 [mac80211]
 [<ffffffffa06dbed1>] __ieee80211_scan_completed+0xc1/0x440 [mac80211]
 [<ffffffffa06dd002>] ieee80211_scan_work+0x82/0x440 [mac80211]
 [<ffffffff810606a3>] process_one_work+0x1e3/0x530
 [<ffffffff81060641>] ? process_one_work+0x181/0x530
 [<ffffffff8106163f>] worker_thread+0x10f/0x3c0
 [<ffffffff81061530>] ? manage_workers+0x330/0x330
 [<ffffffff810665da>] kthread+0xea/0xf0
 [<ffffffff810664f0>] ? kthread_create_on_node+0x140/0x140
 [<ffffffff8146085c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810664f0>] ? kthread_create_on_node+0x140/0x140

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RX fifo can be accessed from the common tasklet or it can
be reaped/cleaned when RX is stopped, which is done when doing
a reset or channel change - this happens in process context.

Since it is ensured that there are no pending tasklets when
stopping RX and cleaning the FIFO, there is no need to use
SKB queue functions which take internal locks.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The EDMA case is handled first, so the else condition
can be removed.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The split makes no sense and merging the functions makes further changes
easier to implement
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

GCC 4.8 is spitting out uninitialized-variable warnings against
"drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c".  This patch adds
initialization to the variable and properly sets its value.

Signed-off-by: Han Shen  (shenhan@google.com)
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. The code only increased the
ack timeout, which is fixed by this patch.

We have noticed in our long shot scenario that we see less collisions
with this patch.
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[add standard reference and commit message]
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Dmitry's address will start bouncing in a few days,
update to his new mail address.

Cc: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cc: Daniel Martensson <Daniel.Martensson@stericsson.com>
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove my soon bouncing email address.
Also remove the "Contact:" line in file header.
The MAINTAINERS file is a better place to find the
contact person anyway.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All radio ops are 16b (there is only 1 exception for reg 0x1), so we
deprecated b43_radio_read16 and b43_radio_write16 long time ago.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>

Sort defines, use one macro for all revs, support for 5GHz when
uploading antenna table.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>

Also make a function name shorter so we can easily fit 80 chars.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>