Newer revs of the FPGA have a larger SD buffer.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The GPIO LEDS driver now has a default state of "keep".  Update the Warp DTS
and platform file to take advantage of this new state.  This removes the
hardcoding of the two LEDs on the Warp.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Now that leds-gpio is a proper OF platform driver, the Warp can use
the leds-gpio driver rather than the old out-of-kernel driver.

One side-effect is the leds-gpio driver always turns the leds off
while the old driver left them alone. So we have to set them back to
the correct settings.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Convert the Warp platform to use the newly merged NDFC driver

- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

FPGA offset in NOR flash was converted incorrectly when switching from
64M to 4M flash.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Added support for the new at24 eeprom driver.
Documented a new fpga section, the DMA scatter gather list.
Removed index from i2c. No longer needed.
Fixed the leds section.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Added led entries.
* Added fpga-sd entry.
* Added ad7414 entry.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

At the moment we have a mixture of left-over version 0 and new-format
version 1 files in arch/powerpc/boot/dts.  This is potentially
confusing to people new to the dts format attempting to figure it out.

So, this patch converts all the as-yet unconverted dts v0 files and
converts them to v1.  They're mechanically-converted, and not hand
tweaked so in some cases they're not 100% in keeping with usual v1
style, but the convertor program does have some heuristics so the
discrepancies aren't too bad.

I have checked that this patch produces no changes to the resulting
dtb binaries.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.

The now obsolete linux,network-index properties are removed from the
corresponding device trees.  This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.

The references to linux,network-index are removed from
booting-without-of.txt.  Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree.  By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the device tree for the PIKA Warp board
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Recent DTC versions disallow certain special characters in full paths without
being quoted with {}.  That however breaks compatibility with older DTC
versions.  Work around this by renaming the CPU nodes for the 4xx files to a
generic node name, and specify the processor type in the model property of the
CPU node.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This removes a bogus empty "ranges" property in the EBC device node
of the Bamboo board device-tree.

The "ranges" property should be created by the wrapper code when it is
implemented.  Until then, remove the empty property since it incorrectly
implies that there is a 1:1 address mapping between the EBC and the OPB.

This also fixes a warning from newer DTCs.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds the definition of the on-chip OHCI controller to the
Bamboo board's device-tree. This is enough to get it probed and
working, though a separate patch fixing a bug in the OHCI driver
is needed to make it reliable.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Fix some device tree omissions that prevented the new EMAC driver from
setting up ethernet on the Bamboo board correctly and update the Bamboo
defconfig.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

According to PowerPC 440EP documentation,
MAL0 consists of 6 channels (4 transmit channels and 2 receive channels)
This patch fixes Bamboo DTS MAL0 "num-rx-chans" entry.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

AMCC Bamboo board DTS
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>