Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 23 6月, 2016 8 次提交
  3. 18 6月, 2016 2 次提交
  5. 16 6月, 2016 1 次提交
    • A
      gpiolib: avoid uninitialized data in gpio kfifo · bc0207a5
      由 Arnd Bergmann 提交于 
      gcc reports a theoretical case for returning uninitialized data in
the kfifo when a GPIO interrupt happens and neither
GPIOEVENT_REQUEST_RISING_EDGE nor GPIOEVENT_REQUEST_FALLING_EDGE
are set:

drivers/gpio/gpiolib.c: In function 'lineevent_irq_thread':
drivers/gpio/gpiolib.c:683:87: error: 'ge.id' may be used uninitialized in this function [-Werror=maybe-uninitialized]

This case should not happen, but to be on the safe side, let's
return from the irq handler without adding data to the FIFO
to ensure we can never leak stack data to user space.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 61f922db ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      bc0207a5
  7. 15 6月, 2016 6 次提交
    • L
      tools/gpio: add the gpio-event-mon tool · 97f69747
      由 Linus Walleij 提交于 
      The gpio-event-mon is used from userspace as an example of how
to monitor GPIO line events. It will latch on to a certain
GPIO line on a certain gpiochip and print timestamped events
as they arrive.

Example output:
$ gpio-event-mon -n gpiochip2 -o 0 -r -f
Monitoring line 0 on gpiochip2
Initial line value: 1
GPIO EVENT 946685798487609863: falling edge
GPIO EVENT 946685798732482910: rising edge
GPIO EVENT 946685799115997314: falling edge
GPIO EVENT 946685799381469726: rising edge
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      97f69747
    • L
      gpio: userspace ABI for reading GPIO line events · 61f922db
      由 Linus Walleij 提交于 
      This adds an ABI for listening to events on GPIO lines.
The mechanism returns an anonymous file handle to a request
to listen to a specific offset on a specific gpiochip.
To fetch the stream of events from the file handle, userspace
simply reads an event.

- Events can be requested with the same flags as ordinary
  handles, i.e. open drain or open source. An ioctl() call
  GPIO_GET_LINEEVENT_IOCTL is issued indicating the desired
  line.

- Events can be requested for falling edge events, rising
  edge events, or both.

- All events are timestamped using the kernel real time
  nanosecond timestamp (the same as is used by IIO).

- The supplied consumer label will appear in "lsgpio"
  listings of the lines, and in /proc/interrupts as the
  mechanism will request an interrupt from the gpio chip.

- Events are not supported on gpiochips that do not serve
  interrupts (no legal .to_irq() call). The event interrupt
  is threaded to avoid any realtime problems.

- It is possible to also directly read the current value
  of the registered GPIO line by issuing the same
  GPIOHANDLE_GET_LINE_VALUES_IOCTL as used by the
  line handles. Setting the value is not supported: we
  do not listen to events on output lines.

This ABI is strongly influenced by Industrial I/O and surpasses
the old sysfs ABI by providing proper precision timestamps,
making it possible to set flags like open drain, and put
consumer names on the GPIO lines.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      61f922db
    • L
      tools/gpio: add the gpio-hammer tool · 2a144dd0
      由 Linus Walleij 提交于 
      The gpio-hammer is used from userspace as an example of how
to retrieve a GPIO handle for one or several GPIO lines and
hammer the outputs from low to high and back again. It will
pulse the selected lines once per second for a specified
number of times or indefinitely if no loop count is
supplied.

Example output:
$ gpio-hammer -n gpiochip0 -o5 -o6 -o7
Hammer lines [5, 6, 7] on gpiochip0, initial states: [1, 1, 1]
[-] [5: 0, 6: 0, 7: 0]
Tested-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      2a144dd0
    • L
      gpio: userspace ABI for reading/writing GPIO lines · d7c51b47
      由 Linus Walleij 提交于 
      This adds a userspace ABI for reading and writing GPIO lines.
The mechanism returns an anonymous file handle to a request
to read/write n offsets from a gpiochip. This file handle
in turn accepts two ioctl()s: one that reads and one that
writes values to the selected lines.

- Handles can be requested as input/output, active low,
  open drain, open source, however when you issue a request
  for n lines with GPIO_GET_LINEHANDLE_IOCTL, they must all
  have the same flags, i.e. all inputs or all outputs, all
  open drain etc. If a granular control of the flags for
  each line is desired, they need to be requested
  individually, not in a batch.

- The GPIOHANDLE_GET_LINE_VALUES_IOCTL read ioctl() can be
  issued also to output lines to verify that the hardware
  is in the expected state.

- It reads and writes up to GPIOHANDLES_MAX lines at once,
  utilizing the .set_multiple() call in the driver if
  possible, making the call efficient if several lines
  can be written with a single register update.

The limitation of GPIOHANDLES_MAX to 64 lines is done under
the assumption that we may expect hardware that can issue a
transaction updating 64 bits at an instant but unlikely
anything larger than that.

ChangeLog v2->v3:
- Use gpiod_get_value_cansleep() so we support also slowpath
  GPIO drivers.
- Fix up the UAPI docs kerneldoc.
- Allocate the anonymous fd last, so that the release
  function don't get called until that point of something
  fails. After this point, skip the errorpath.
ChangeLog v1->v2:
- Handle ioctl_compat() properly based on a similar patch
  to the other ioctl() handling code.
- Use _IOWR() as we pass pointers both in and out of the
  ioctl()
- Use kmalloc() and kfree() for the linehandled, do not
  try to be fancy with devm_* it doesn't work the way I
  thought.
- Fix const-correctness on the linehandle name field.
Acked-by: NMichael Welling <mwelling@ieee.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      d7c51b47
    • A
      gpio: pca953x: enable driver on Intel Edison · 747e42a1
      由 Andy Shevchenko 提交于 
      Intel Edison board has 4 GPIO expanders PCA9555a connected to I2C bus. Add an
ID to support them.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      747e42a1
    • R
      gpio: acpi: add _DEP support for Acer One 10 · 3f86a635
      由 Rui Zhang 提交于 
      On Acer One 10, the ACPI battery driver can not be probed because
it depends on the GPIO controller as well as the I2C controller to work,
        Device (BATC)
        {
            Name (_HID, EisaId ("PNP0C0A") /* Control Method Battery */)
            ...
            Name (_DEP, Package (0x03)  // _DEP: Dependencies
            {
                I2C1,
                GPO2,
                GPO0
            })
            ...
        }

The I2C dependency also exists on other platforms and has been fixed by commit
40e7fcb1 ("ACPI: Add _DEP support to fix battery issue on Asus T100TA"),
this patch resolves the GPIO dependency for Acer One 10.

Link:https://bugzilla.kernel.org/show_bug.cgi?id=115191Tested-by: NStace A. Zacharov <stace75@gmail.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      3f86a635
  9. 14 6月, 2016 2 次提交
  11. 13 6月, 2016 2 次提交
  13. 08 6月, 2016 16 次提交
  15. 07 6月, 2016 3 次提交