Reloading FW during resets can cause issues. Remove the full reset
as it is not needed.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for WOL as determined by the EEPROM.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to avoid a hardware lockup when Tx work is still
pending and we request a reset.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for configuring the priority to
traffic class mapping.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need SFP+ plugable support for X540 hardware (copper only) so
don't enable the SFP+ interrupts.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The DCB CEE command set_state() will complete successfully
but is misleading because it enables IEEE mode. After
this patch the command is failed.

And IEEE PFC/ETS is managed from ieee paths now instead
of using CEE primitives.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the PCI device flag indicating if a VF is assigned to a guest VM
to guard against destroying VFs upon driver removal.  Implement
additional feature to detect if VFs already exist when the driver
is loaded and if so configure them and set the driver state to
SR-IOV enabled.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

netif_tx_start_all_queues() is already called in ixgbe_up_complete, no need
to do it twice.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove duplicate inc of hwstats->ruc
Introduce separate loops for 8 and 16 register reads.
Consolidate mac checks under one case.
Make sure registers are cleared on read.
Reported-by: NJonathan Lynch <jonathan.lynch@thenowfactory.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
CC: Jonathan Lynch <jonathan.lynch@thenowfactory.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch improves the memory utilization with RSC when in one-buffer
mode.  This is accomplished by making the default buffer sizes match up
with the standard memory allocation sizes minus 1K for shared info and
padding overhead.  By doing this CPU utilization when doing large receives
can be reduced by as much as 8%.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The adapter structure was removed from the call so it can be dropped from
the ixgbe_fso documentation.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One of the 82598 phys was not being correctly identified as being SFP.
This change corrects that.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds a small bit of missing code for enabling the overheat sensor
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_up and ixgbe_up_complete will always return 0.  Since this doesn't
provide any useful information we might as well just make them both void
and save ourselves from having to return an unused value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes an issue in which the incorrect amount of headroom was
being reserved for flow director filters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes a minor redundancy in that tx_sample_rate was set twice.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A user-space process must use ETHTOOL_GRXCLSRLCNT to find the number
of classification rules, then allocate a buffer of the right size,
then use ETHTOOL_GRXCLSRLALL to fill the buffer.  If some other
process inserts or deletes a rule between those two operations,
the user buffer might turn out to be the wrong size.

If it's too small, the return value will be -EMSGSIZE.  But if it's
too large, there is no indication of this.  Fix this by updating
the rule_cnt field on return.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.

Add note that drivers must not use ethtool_rxnfc::rule_locs.

The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was possible to inadvertently add additional interrupt causes to the
MSI-X other interrupt.  This occurred when things such as RX buffer overrun
events were being triggered at the same time as an event such as a Flow
Director table reinit request.  In order to avoid this we should be
explicitly programming only the interrupts that we want enabled.  In
addition I am renaming the ixgbe_msix_lsc function and interrupt to drop
any implied meaning of this being a link status only interrupt.

Unfortunately the patch is a bit ugly due to the fact that ixgbe_irq_enable
needed to be moved up before ixgbe_msix_other in order to have things
defined in the correct order.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to cleanup some of the code related to SR-IOV and the
interrupt registers.  Specifically I am moving the EITRSEL configuration
into the MSI-X configuration section instead of enablement.  Also I am
fixing the VF shutdown path since it had operations in the incorrect order.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The reset paths are overly complicated and are either missing steps or
contain extra unnecessary steps such as reading MAC address twice.  This
change is meant to help clean up the reset paths an get things functioning
correctly.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updated the TXDCTL configuration.  The main goal is to be much
more explicit about the configuration and avoid a possible fake TX hang
when the interrupt throttle rate is set to 0.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a minor whitespace cleanup to compress the device ID
declaration and board type declaration onto the same line.  It seems to
make sense since all of the combinations of the two are less than 80
characters and it makes the overall layout a bit more readable.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch drops a set of unnecessary dereferences to the hardware structure
since we already have a local copy of the hardware pointer.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it so that the map_rings_to_vectors call will work with
all interrupt types.  The advantage to this is that there will now be a
predictable mapping for all given interrupt types.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change switches us over to using the ring->dev pointer instead of
having to use the adapter->pdev->dev reference.  The advantage to this is
that it is a much shorter route to get the to final needed value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The allocation and freeing of the IRQ affinity hint needs some updates
since there are a number of spots where we run into possible issues with
the hint not being correctly updated.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change consolidates all of the MSI-X interrupt and polling routines
into two single functions.  One for the interrupt and one for the code.
The main advantage to doing this is that the compiler can optimize the
routines into single monolithic functions which should allow all of them
function to occupy a single block of memory and as such avoid jumping
around.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the default Tx work limit is 256 buffers or
1/2 of an entire ring instead of a full ring size so that it is much more
likely that we will be able to actually reach the work limit value.
Previously with the value set to an entire ring it would not have been
possible for us to trigger an event due to the fact that the Tx work is
stopped at the point where we cannot place one more buffer on the ring and
it is not restarted until cleanup is complete.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RNBC (0x03FC0) is only for 82598 and has different meaning
on newer HW. Make sure to only clear it for 82598.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When setting advertised speed/duplex with ethtool.

Also cleaned up the comment since we also support 100/F.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A logic error in ixgbe_fc_autoneg_fiber() that treated a masked u32 as a
boolean would make it so we would never fall hit a error check case.  So
now I force the u32 to a boolean value with '!!'.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I'm removing NETIF_F_GRO from being initialed in the feature flags during
ixgbe_probe() bases on a comment from Michal Miroslaw
<mirq-linux@rere.qmqm.pl> that it is always set by network code now.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X540 devices do not clear PFC before sets. This results in
the device possibly responding to PFC frames that the user
has disabled. Although it would also be wrong for the peer
to be transmitting these frames. Now we clear the register
before set.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This consolidates setup code for multiple traffic classes in
the setup_tc routine.

Prep work to allow IEEE DCBX to optimize for number of traffic
classes. Also simplifies code paths.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The packet buffer is correctly allocated by generic pb allocation
path in ixgbe_configure() there is no need to do the allocation
here as well.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>

One existing call sites still expect either 4 or 8 traffic
classes to be specified. This fixes this allowing arbitrary
values up to 8 to work as expected.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to fix the patch:
	ixgbe: Cleanup FCOE and VLAN handling in xmit_frame_ring
And can be rolled into it if needed.

What this fixes is that VLAN tagged packets were not being tagged if they
were prio 7 which matches up with TC_PRIO_CONTROL.  In order to fix it I am
just setting things up so that we always tag VLAN tagged packets.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>