Implements basic pinmux for the Nomadik pin controller.

The plan is to split the existing singular pin config interface
nmk_config_pin(), nmk_config_pins(), that will configure muxing
and other settings at the same time, into two interfaces
by splitting the code in pinmux and pinctrl and eventually
deleting the old interface and its helper functions when all
users are gone.

nmk_gpio_set_mode() and nmk_gpio_get_mode() are two older
interfaces for just configuring muxing/altfunctions that
will also be replaced in the end.

We take some extra care to handle the glitch-avoidance here,
but it is simpler now since there is only one altsetting per
pingroup so we know immediately if we need to avoid altfunc
C glitches for a certain group.

As part of the makeover implement the .request() and .free()
calls on the GPIO chips and have them call back into the
pinctrl layer to reserve GPIOs.

ChangeLog v1->v2:
- Rebased on pinctrl-mergebase-20120418 so we get the latest
  driver infrastructure where function count is done by a fixed
  value and we can drop a few range checks since this is now
  handled by the core.
- Include a GPIO muxing hunk erroneously part of the pin config
  patch.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since all pins we can control are GPIOs, match a GPIO range to
each pin in the debug function and call into the GPIO debug
print function to have the per-pin information.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Break out the code displaying the status of a single pin so we
can use the same code in the pinctrl debug function.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds a scratch pin control interface to the Nomadik pinctrl
driver, and defines the pins and groups in the DB8500 ASIC. We
define GPIO ranges to cover the pins exposed. The DB8500 has
more pins than this but we restrict the driver to the pins that
can be controlled from the combined GPIO and pin control hardware
to begin with.

ChangeLog v1->v2:
- Base on the latest pinctrl development from
  pinctrl-mergebase-20120418 so we can get rid of legacy
  group count mechanism. Also drop the range checks for group
  index, this is handled by the core now.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

a60b57ed "drivers/gpio: gpio-nomadik: Add support for irqdomains" broke
building with CONFIG_OF_GPIO disabled.

Without this patch, building nhk8815_defconfig results in:

/home/arnd/linux-arm/drivers/gpio/gpio-nomadik.c: In function 'nmk_gpio_probe':
/home/arnd/linux-arm/drivers/gpio/gpio-nomadik.c:1238:6: error: 'struct gpio_chip' has no member named 'of_node'
make[3]: *** [drivers/gpio/gpio-nomadik.o] Error 1
make[2]: *** [drivers/gpio] Error 2
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [drivers] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [sub-make] Error 2
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

I'm moving this driver over to the pinctrl subsystem to convert
the custom pin mux/config scheme over to use pinctrl.
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add irq domain support to the gpio-nomadik GPIO driver. This
enables its users to support dynamic IRQ assignment, which is
requried by Device Tree.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We were using a custom io_p2v() (physical-to-virtual) translation
macro, but it's fully possible to just ioremap() this memory
now, so skip use of static addresses altogether.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Low EMI (Electro-Magnetic Interference) mode means lower slew
rate on the signals. The Nomadik GPIO controller supports
this so create an interface to enable it.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

If the pin is switching to altfunc, and there was an interrupt
installed on it which has been lazy disabled, actually mask the
interrupt to prevent spurious interrupts that would occur while
the pin is under control of the peripheral. Only SKE does this.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Cache two more registers in the GPIO controller.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Setting GPIOs' SLPM value to 1 (WAKEUP_DISABLE) is seen to cause
increased power consumption in sleep/deep-sleep. So remove the code
which disables SLPM based on the wakeup settings and only ensure
it is on as needed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds a kernel message, containing GPIO range and device
name on successful device registration, and removes duplicate messages from the following drivers:
	* gpio-adp5588
	* gpio-bt8xx
	* gpio-cs5535
	* gpio-janz-ttl
	* gpio-nomadik
	* gpio-pcf857x
	* gpio-xilinx
	* drivers/of/gpio.c
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
[grant.likely@secretlab.ca: squashed 2 patches together]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Currently the Nomadik GPIO driver tracks enabled/disabled interrupt
status with a local variable, switch to using the interrupt core.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.

Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: NAxel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NRickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: NMartin Persson <martin.persson@stericsson.com>
[Split off from larger patch]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Useful to check the status of the runtime pin muxing.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Squashed, modified to use chip-internal IRQ trigger state]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch updates the Nomadik gpio chained IRQ handler to use the
chained IRQ enter/exit functions in order to function correctly on
primary controllers with different methods of flow control.

Cc: Rabin Vincent <rabin@rab.in>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Use irq_set_chip_and_handler() instead. Converted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Convert to the new function names. Automated with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Store the enabled mask in the local state, so there is no need to
fiddle in the irq descriptor.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

gpiolib plus two gpio implementations in arm fiddle in the guts of
irq_desc in a racy and buggy way. Remove the stuff. I already told the
gpio folks that we can provide that information in a proper way if
necessary.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212508.931638262@linutronix.de>

Enable wakeups by default for any GPIO interrupts and in the suspend/resume
path narrow this down to only the the real wakeup interrupts. This approach is
based on the assumption that cpuidle ApSleep will be entered more often than
system suspend.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixup for genirq changes to struct irq_data on 2.6.38]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The compiler warns that [rf]wimsc may be used uninitialized in
this function - the warning is actually false since the uses are
in identical if()-clauses, but it can't hurt very much to read
out the values to be modified early anyway and rid the warning.

Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The NOMADIK_GPIO_PM config option is disabled by default, not user visible,
and never selected by any other option: the code is therefore unused. The
GPIO registers need not be saved and restored since their values are
preserved when vAPE (on DB8500) is powered down.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: NJonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch fixes a bug when setting SLPM register for DB8500.
When calling__nmk_gpio_set_slpm(...) offset to GPIO is now used
instead of the GPIO number itself.
Signed-off-by: NRikard Olsson <rikard.p.olsson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Setting pinmux alternative C for a GPIO pin is actually not
so easy since it ivolves setting value "1" in two registers,
and since the combined result will take effect for intermediate
values (01 or 10) this will cause glitches while you wrote one
register but have not yet written the other.

This patch implements a series of kludges including an optional
machine-specific callback to avoid glitches when changing pin
mux mode to alternative C.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Coverity found that we were checking an unsigned variable for
>= zero. Type it correctly so that the check works as intended.
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Suspend/resume didn't take care of pull-up and pull-down
settings and writing back the DAT register at resume can
change pull up/down settings, depending on pin input value.
Output values are now also restored.
Signed-off-by: NJonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When GPIOs wake up the system from sleep mode, the normal GPIO interrupt
handler does not hit and the normal interrupt status register does not
contain the status. Instead the secondary GPIO handler does, and the
interrupt status needs to be retrieved from the wakeup status saved by
the suspend/resume code.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
[Added constant 32-pin assignment in platform data]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>