This patch adds MBSS extensible synchronization framework (Sec.
13.13.2 of IEEE Std. 802.11-2012).

The framework is implemented via an ops table which defines the
following functions:

    rx_bcn_presp() - this is called every time a mesh beacon is
received.
    adjust_tbtt() - this is called immediately before a beacon is about
to be transmitted.

The default neighbor offset synchronization defined in the standard is
implemented.  We also provide template functions for vendor specific
methods.

When neighbor offset synchronization is active (which is the default)
mesh neighbors in the same MBSS will track timing offsets to each other
and compensate clock drift.

In our tests we observed that this mesh synchronization implementation
successfully corrected drifts between stations of ~2PPM while
introducing a jitter of ~20us.

It is also possible to test this framework on mac80211_hwsim simulated
phys to see how it behaves under different topologies, over poor links,
etc.
Signed-off-by: NMarco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: NPavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reading and writing back the tsf value via tsf is too slow if one wants
to make small increments to this timer.  With this change you can use
the syntax "+=<some value>" or "-=<some value>" to add or substract a
value from the tsf counter.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Generate more acurate tsf values in hwsim by setting the tsf value on
trasmitted beacons immediately before they are moved to the rx path.
Also, adjust the beacon timestamp to be the time at which the first byte
of the timestamp is transmitted.

With these changes the observed tsf offset between two hwsim/mesh peers
is 0 (unless the offset is modified via debugfs)
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While associated we should never have empty SSID, but life can be full
of surprises, and is allways better to print a warning than crash.

Before memcpy() in ieee80211_probereq_get() check ssid_len instead of
ssid pointer, sice pointer it always passed by "ssidie + 2" expression
to send probe functions, so practically never can be NULL.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When adding pending SKBs there's no need to
stop all queues, we only need to stop those
that we're adding frames to. Implement that
by lazily stopping a queue as we add an SKB.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the queue status changes we need to do a fair
bit of work, so ignore no-op changes early.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.

Also fix up the restart code to not try to set up
the queues in this case.

Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.

Also verify that the AC number given is valid.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This field is never set to anything non-zero in
mac80211, so we should be able to remove it.
Unfortunately though, the iwlwifi and iwlegacy
drivers use it for their internal TX status
processing (which shouldn't be using the rate
control API to start with), so add a new field
"status.antenna" for them, at least for now.

In the future, I plan to use the new field to
hold the hardware queue, while the SKB's queue
mapping holds the AC.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.

Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We currently stop the queue when changing the rate
control between 20/40 MHz in the BSS. This seems to
have been necessary when we actually changed the
channel, but now that we just update the station it
doesn't seem right any more. Remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel type argument to the rate_update()
callback isn't really the correct way to give
the rate control algorithm about the desired
RX bandwidth of the peer.

Remove this argument, and instead update the
STA capabilities with 20/40 appropriately. The
SMPS update done by this callback works in the
same way, so this makes the callback cleaner.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changing the channel type during operation is
confusing to some drivers and will be hard to
handle in multi-channel scenarios. Instead of
changing the channel, set it to the right HT
channel before authenticating/associating and
don't change it -- just update the 20/40 MHz
restrictions in rate control as needed when
changed by the AP.

This also fixes a problem that Paul missed in
his fix for the "regulatory makes us deaf"
issue -- when we couldn't use 40 MHz we still
associated saying we were using 40 MHz, which
could in similarly broken APs make us never
even connect successfully.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the AC constants instead of hard-coding
the numbers with comments.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a trivial wrapper function, inline it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no reason for it to not be static.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up the code formatting and also replace
the constant 0 by IEEE80211_AC_VO.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix bad indentation & pointless if nesting.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IEEE80211_MAX_QUEUES is an internal mac80211 value,
it is not guaranteed to be always 4. The firmware
API in mwifiex almost certainly doesn't care about
mac80211 changing though, so mwifiex shouldn't use
this value.

Maybe it should use IEEE80211_NUM_ACS instead and
that is what I'm doing here as at least that value
will probably never change, but maybe it should
have its own define instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.

Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.

Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In https://bugzilla.kernel.org/show_bug.cgi?id=42976, a system with driver
rtl8192se used as an AP suffers from "Out of SW-IOMMU space" errors. These
are caused by the DMA buffers used for beacons never being unmapped.

This bug was also reported at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/961618Reported-and-Tested-by: NDa Xue <da@lessconfused.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prefix dmesg output with "iwlwifi: " by
adding #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the case of disabled CONFIG_IWLWIFI_DEBUGFS option the compiler complains
about the unused variable 'img'. Fix this by moving the 'img' definition.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Macros can be converted to functions to reduce overall object size.

Convert the ATH5K_PRINTK macro to use _ath5k_printk.

Allyesconfig size is reduced ~10%

$ size drivers/net/wireless/ath/ath5k/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 211557	   2032	  40672	 254261	  3e135	drivers/net/wireless/ath/ath5k/built-in.o.new
 235412	   2032	  47296	 284740	  45844	drivers/net/wireless/ath/ath5k/built-in.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the POWER_PMI to the op_mode where it is changed.  The trans needs
to check it frequently, so shadow the status in the trans and update it
in trans when it infrequently changes.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The op_mode should check for FW_ERROR before calling send_cmd.  This
removes the need to test for FW_ERROR in the trans layer.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With error logging now completely handled in
the op_mode, the transport layer does not
need to know information about the loaded
firmware.

Remove this state information from the
iwl_shared data structure.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_get_single_channel_number is used only in
iwl-scan.c, move it there and mark it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_full_rxon_required is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_check_rxon_cmd is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_set_rxon_hwcrypto is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_send_rxon_timing is used only in
iwl-agn-rxon.c, move it there and mark it
static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used only in one file, move it there
and make it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This variable holds the ucode currently
running on the device; which is determined by
op_mode, so move this parameter there.

Also, the name of the variable is a bit
misleading, so rename it to cur_ucode.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Error log reporting does not belong to the
transport layer, but to the op_mode loading
the ucode, as it is the entity which knows
about the ucode loaded, and what the error
information means.

Move device logging pointers from the
transport layer to op_mode.

With this change, transport layer only
reports an error to the op_mode, which will
figure out what to do with the error. This
causes the driver to now dump out error logs
when the command queue is stuck as well.

Also, move the debugfs entry for event logs
out of the transport layer and into op_mode.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_nic_error is used in iwl-agn.c only, move
it there and make it static.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the process, make iwlagn_fw_error
a non-static function, as it is used
by more than one file.
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>