Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The JPEG header is now included in the subdriver structure instead
of being allocated and freed at capture start and stop.
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

setcolors(0 is a no-op for 7670 sensors, so we should not report a
saturation control for 7670 sensors.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

What we've called brightness so far actually is an exposure control,
rename it and fixup the maximum and default values.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

gspca_tv8532: add gain control
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There is a problem with certain tv8532 cams, where sometimes there
hsync/vsync locks one pixel of where it normally locks. While trying to
fix this (which I failed to do). I noticed there are lots if duplicate
register writes and unnecessary register reads in the tv8532 driver. This
patch cleanes these ups (which has no negative effects, but unfortunately
also does not help).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With the ovfx2 bridge sometimes the first few frames in a stream
would be no good, as the bridge and sensor are not in complete hsync /
vsync yet. This can easily be detected by checking the framesize. So if the
framesize is short and it is one of the 1ste 3 frames after an sd_start,
drop it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is a new driver for the Windows Media Center Edition/eHome
Infrared Remote transceiver devices. Its a port of the current
lirc_mceusb driver to ir-core, and currently lacks transmit support,
but will grow it back soon enough... This driver also differs from
lirc_mceusb in that it borrows heavily from a simplified IR buffer
decode routine found in Jon Smirl's earlier ir-mceusb port.

This driver has been tested on the original first-generation MCE IR
device with the MS vendor ID, as well as a current-generation device
with a Topseed vendor ID. Every receiver supported by lirc_mceusb
should work equally well. Testing was done primarily with RC6 MCE
remotes, but also briefly with a Hauppauge RC5 remote, and all works
as expected.

v2: fix call to ir_raw_event_handle so repeats work as they should.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is the RC6 keymap for the Windows Media Center Edition remotes
that come bundled with MCE/eHome Infrared Remote transceivers. Tested
with 3 different variants of the remote, but its possible there are
still some additional keys missing, but its simple enough to add them
in later...

This patch also adds an IR_TYPE_ALL convenience macro to make life
easier for receivers that support all IR protocols.

v2: fix an erroneous comment that referred to imon devices
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rather than registering all IR protocol decoders as enabled when bringing
up a new device, only enable the IR protocol decoder that matches the
keymap being loaded. Additional decoders can be enabled on the fly by
those that need to, either by twiddling sysfs bits or by using the
ir-keytable util from v4l-utils.

Functional testing done with the mceusb driver, and it behaves as expected,
only the rc6 decoder is enabled, keys are all handled properly, etc.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On Fri, May 28, 2010 at 3:59 PM, Jarod Wilson <jarod@redhat.com> wrote:
> The mceusb driver I'm about to submit handles just about any raw IR you
> can throw at it. The ir-core loads up all protocol decoders, starting
> with NEC, then RC5, then RC6. RUN_DECODER() was trying them in the same
> order, and exiting if any of the decoders didn't like the data. The
> default mceusb remote talks RC6(6A). Well, the RC6 decoder never gets a
> chance to run unless you move the RC6 decoder to the front of the list.
>
> What I believe to be correct is to have RUN_DECODER keep trying all of
> the decoders, even when one triggers an error. I don't think the errors
> matter so much as it matters that at least one was successful -- i.e.,
> that _sumrc is > 0. The following works for me w/my mceusb driver and
> the default decoder ordering -- NEC and RC5 still fail, but RC6 still
> gets a crack at it, and successfully does its job.
>
> Signed-off-by: Jarod Wilson <jarod@redhat.com>
>
> ---
>  drivers/media/IR/ir-raw-event.c |    7 ++++---
>
> diff --git a/drivers/media/IR/ir-raw-event.c b/drivers/media/IR/ir-raw-event.c
> index ea68a3f..44162db 100644
> --- a/drivers/media/IR/ir-raw-event.c
> +++ b/drivers/media/IR/ir-raw-event.c
> @@ -36,14 +36,15 @@ static DEFINE_SPINLOCK(ir_raw_handler_lock);
>  */
>  #define RUN_DECODER(ops, ...) ({                                           \
>        struct ir_raw_handler           *_ir_raw_handler;                   \
> -       int _sumrc = 0, _rc;                                                \
> +       int _sumrc = 0, _rc, _fail;                                         \
>        spin_lock(&ir_raw_handler_lock);                                    \
>        list_for_each_entry(_ir_raw_handler, &ir_raw_handler_list, list) {  \
>                if (_ir_raw_handler->ops) {                                 \
>                        _rc = _ir_raw_handler->ops(__VA_ARGS__);            \
>                        if (_rc < 0)                                        \
> -                               break;                                      \
> -                       _sumrc += _rc;                                      \
> +                               _fail++;                                    \
> +                       else                                                \
> +                               _sumrc += _rc;                              \

Self-NAK. The only place we actually *care* about the retval from a
RUN_DECODER() call is in __ir_input_register(), and currently, its
looking for retval < 0, which is currently never possible. When we're
running the decoders, either they fail and return -EINVAL or they
succeed and return 0, and in the register case, we get either a
negative error (ex: -ENOMEM from rc6) or 0, so with the above, _sumrc
will *always* be 0 in the two cases I'm looking at. The third place
where RUN_DECODER gets called (decoder unregister) doesn't care about
the retval either. New patch below, including updated comments about
the macro.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With enabled debugging sh_mobile_ceu_camera.c dereferences an invalid or a NULL
pointer. Thanks to James Wang for reporting.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

These function are needed to use camera.
This patch was tested with sh_mobile_ceu_camera
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Calling g_fmt before s_fmt resulted in a NULL pointer dereference as no
default formats were being selected on probe.
Reported-by: NNémeth Márton <nm127@freemail.hu>
Signed-off-by: NPawel Osciak <p.osciak@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Issuing a GET_MIN request on the power line frequency control times out
on at least the Apple iSight. As the UVC specification doesn't list
GET_MIN/MAX/RES as supported on that control, remove them from the
uvc_ctrls array.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a short delay when stopping the decoder, allowing it to settle and
preventing some unexpected interaction with other firmware commands.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Tested-by: NMartin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Hauppauge EEPROM tuner code 168 has recently shown up on HVR-1600 TV
capture cards supported by the cx18 driver.  This change allows analog
tuner type autodetection to succeed for these cards.

Information for decoding tuner code 168 was provided by Hauppauge.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMuralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Actually OMAP doesn't support scatter-gather DMA for
Display subsystem but due to legacy coding it has been overlooked
till now.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMuralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changes -
	- Kconfig option dependancy changed to ARCH_OMAP2/3 from
	ARCH_OMAP24XX/34XX
	- There are some moments of function from omap_dss_device
	to omap_dss_driver. Incorporated changes for the same.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMuralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b0 to fix the faulty drivers.

As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NRichard Purdie <rpurdie@linux.intel.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Added small delay on device open & close to allow hardware to settle. Move yuv
register restore to before the decoder firmware call to stop playback.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For yuv video output, pass fake values to avoid firmware trying to change
video standard.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Check firmware state when loading module & if firmware is not responding exit
with an error. When module is unloaded, only disable the framebuffer & not all
decoder output.
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[Andy Walls comment:] This patch from Ian removes the cx2341x module lying
about the setting of the temporal filter for the log status ioctl().
Signed-off-by: NIan Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A trivial change to update my email address from my dead awalls@radix.net
address to my current awalls@md.metrocast.net address.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In each case, the print involves dereferencing a value that is NULL or is
near NULL.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@

if ((E == NULL && ...) || ...)
{
  ... when != if (...) S1 else S2
      when != E = E1
* E->f
  ... when any
  return ...;
}
else S3
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix ULE decapsulation bug when less than 4 bytes of ULE SNDU is packed
into the remaining bytes of a MPEG2-TS frame

ULE (Unidirectional Lightweight Encapsulation RFC 4326) decapsulation
code has a bug that incorrectly treats ULE SNDU packed into the
remaining 2 or 3 bytes of a MPEG2-TS frame as having invalid pointer
field on the subsequent MPEG2-TS frame.
Signed-off-by: NAng Way Chuang <wcang@nav6.org>
Acked-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It makes IR to work again for dm1105 and, possibly, others.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix ir-nec-decoder build: it uses bitrev library code, so
select BITREVERSE in its Kconfig.

ir-nec-decoder.c:(.text+0x1a2517): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2526): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2530): undefined reference to `byte_rev_table'
ir-nec-decoder.c:(.text+0x1a2539): undefined reference to `byte_rev_table'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The problem is that dprintk() dereferences "dev" which is null here.
The i2cdprintk() uses "ir" so that's OK.

Also Jean Delvare pointed out a typo in the comment so we may as well
fix that.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The original code had two break statements in a row.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add auto-config support for iMON 2.4G LT RF device, based on
debug output from Giulio Amodeo in Red Hat bugzilla #572288.

Also flips the switch on only setting up the rf associate sysfs
attr only if we think we're looking at an RF device, vs. previously,
setting up the attr for all 0xffdc devices, so its possible (but a bit
unlikely) there's another iMON RF device we'll have to fix up.

Nb: should be applied after "IR/imon: clean up usage of bools", or there
will be a slight contextual mismatch.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There was a mix of 0/1 and false/true. Pick one convention and stick
with it (I picked false/true).
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The "dev" variable is used as a list cursor in a list_for_each_entry()
loop and can never be null here so I removed the check.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove unused #include <linux/version.h>('s) in
  drivers/media/dvb/ngene/ngene-dvb.c
  drivers/media/dvb/ngene/ngene-i2c.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add slab.h to fix ak881x build:

drivers/media/video/ak881x.c:265:error: implicit declaration of function 'kzalloc'
drivers/media/video/ak881x.c:265:warning: assignment makes pointer from integer without a cast
drivers/media/video/ak881x.c:283:error: implicit declaration of function 'kfree'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>