Currently the machine hangs during booting while accessing the
BXT_MIPI_PORT_CTRL register during pipe HW state readout. After some
experimentation I found that the hang is caused by the DSI PLL being
disabled, or it being enabled but with an incorrect divider
configuration. Enabling the PLL got rid of the boot problem, so fix
this by checking the PLL enabled state/configuration before attempting
to read out the HW state.

The DSI_PLL_ENABLE register is in the always-on power well, while the
BXT_DSI_PLL_CTL is in power well 0. This isn't exactly matched by the
transcoder power domain, but what we really need is just a runtime PM
reference, which is provided by any power domain.

Ville also found this dependency specified in BSpec, so I added a
reference to that too.

v2:
- Make sure we hold a power reference while accessing the PLL registers.
v3: (Jani)
- Simplify check in bxt_get_dsi_transcoder_state()
- Add comment explaining why we check for valid dividers in
  bxt_dsi_pll_is_enabled()

CC: Shashank Sharma <shashank.sharma@intel.com>
CC: Uma Shankar <uma.shankar@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Fixes: c6c794a2 ("drm/i915/bxt: Initialize MIPI DSI for BXT")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458816100-31269-1-git-send-email-imre.deak@intel.com

This patch contains following changes:
1. Add BXT MIPI display address base.
2. Call dsi_init from display_setup function.

v2: Rebased on latest nightly branch

v3 by Jani: init dsi after ddi
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458640910-5338-1-git-send-email-jani.nikula@intel.com

Patch based on a previous series by Shashank Sharma.

v2: Update contributors

v3: Refactor degamma/gamma LUTs load into a single function

v4: Remove unused variable
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NKumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: NKausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-5-git-send-email-lionel.g.landwerlin@intel.com

Patch based on a previous series by Shashank Sharma.

v2: Do not read GAMMA_MODE register to figure what mode we're in

v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0

    Add documentation on how the Broadcast RGB property is affected by CTM

v4: Update contributors

v5: Refactor degamma/gamma LUTs load into a single function

v6: Fix missing intel_crtc variable (bisect issue)

v7: Fix & simplify limited range matrix multiplication (Matt Roper's
    comment)
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NKumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: NKausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com

This is needed for the Mesa Vulkan driver on Haswell.
Signed-off-by: NJordan Justen <jordan.l.justen@intel.com>
Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457335830-30923-5-git-send-email-jordan.l.justen@intel.com

This allows writes to EU flow control registers. Together
with SIP code from the user-mode driver this resolves a
hang seen in some pre-emption scenarios. Note that this
patch is just the kernel mode part of this workaround.

v2. Oops, add FLOW_CONTROL_ENABLE macro to i915_reg.h.
Signed-off-by: NTim Gore <tim.gore@intel.com>
Reviewed-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458144826-17269-1-git-send-email-tim.gore@intel.com

In full gpu reset we prime all engines and reset domains corresponding to
each engine. Per engine reset is just a special case of this process
wherein only a single engine is reset. This change is aimed to modify
relevant functions to achieve this. There are some other steps we carry out
in case of engine reset which are addressed in later patches.

Reset func now accepts a mask of all engines that need to be reset. Where
per engine resets are supported, error handler populates the mask
accordingly otherwise all engines are specified.

v2: ALL_ENGINES mask fixup, better for_each_ring_masked (Chris)
v3: Whitespace fixes (Chris)
v4: Rebase due to s/ring/engine

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458143640-20563-1-git-send-email-mika.kuoppala@intel.com

BXT isn't as limited as BYT and CHT regarding DSI pipes and ports.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8bea85b86aaf7a15f854a656bf8d3208a3afe0bd.1458070700.git.jani.nikula@intel.com

The enum mipi_dsi_pixel_format defines MIPI_DSI_FMT_RGB666 for the
"loose" 24 bpp format and MIPI_DSI_FMT_RGB666_PACKED for the 18 bpp
format. We have this the other way round, defining a loose version for
24 bpp.

Follow suit with what's in enum mipi_dsi_pixel_format to avoid future
confusion. Rename

VID_MODE_FORMAT_RGB666 -> VID_MODE_FORMAT_RGB666_PACKED
VID_MODE_FORMAT_RGB666_LOOSE -> VID_MODE_FORMAT_RGB666
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458123700-16003-1-git-send-email-jani.nikula@intel.com

Currently we assume that hrawclk is 200MHz on VLV/CHV. That should
be true always, but just to avoid such asumptions we can read out the
actual frequency from CCK.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456932138-14004-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The MIPI clock calculations for the addtional clock
are revised from B0 stepping onwards, the bit definitions
have changed compared to old stepping.

v2: Fixing compilation warning.
v3: Retained the old Macros (Jani)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Tested-by: Ramalingam C <ramalingam.c@intel.com> # BXT-T with Tianma panel
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455556437-29267-1-git-send-email-m.deepak@intel.com

Rather than assume the VGA dotclock is really the FDI based thing,
let's read out the real thing via iclkip, and after readout it'll
get to compare it with the FDI based number to make sure they're
in sync.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455738073-14502-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Cores need to be included into the debug mask. We don't exactly
know what it does but the spec says it must be enabled. So obey.

v2: Cores should be only set for BXT (Imre, Art)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455877564-5128-1-git-send-email-mika.kuoppala@intel.com

Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.

So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.

So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.

[1] https://bugzilla.kernel.org/show_bug.cgi?id=52361

Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Nick Bowler <nbowler@draconx.ca>
References: https://lists.freedesktop.org/archives/dri-devel/2016-February/100382.htmlReported-by: NNick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Fixes: 237ed86c ("drm/i915: Check live status before reading edid")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455127145-20087-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 0780cd36)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.

So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.

So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.

[1] https://bugzilla.kernel.org/show_bug.cgi?id=52361

Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Nick Bowler <nbowler@draconx.ca>
References: https://lists.freedesktop.org/archives/dri-devel/2016-February/100382.htmlReported-by: NNick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Fixes: 237ed86c ("drm/i915: Check live status before reading edid")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455127145-20087-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We accidentally point both cfgcr registers for the second shared DPLL to
the same location in i915_reg.h. This results in a lot of hw pipe state
mismatches whenever we try to do a modeset that requires allocating the
DPLL to a CRTC:

[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)

This usually ends up causing blank monitors, since the DPLL never can
get set to the right clock.

Fixes: 086f8e84 ("drm/i915: Prefix raw register defines with underscore")
Signed-off-by: NLyude <cpaul@redhat.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454600601-21900-1-git-send-email-cpaul@redhat.com
(cherry picked from commit da3b891b)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Some Gen7/8 production parts may have the Display Pipe C fused off.
In this case, the display hardware will prevent the enable bit in
PIPE_CONF register (for Pipe C) from being set to 1.

Fixed by adjusting pipe_count to reflect this.

v2: Rename HSW_PIPE_C_DISABLE to IVB_PIPE_C_DISABLE as it already exists
    on ivybridge (Ville)
v3: Remove unnecessary MMIO read, correct the description (Damien)
v4: Be more specific in description (Patrick)
Signed-off-by: NGabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453462125-21519-1-git-send-email-gabriel.feceoru@intel.com

We accidentally point both cfgcr registers for the second shared DPLL to
the same location in i915_reg.h. This results in a lot of hw pipe state
mismatches whenever we try to do a modeset that requires allocating the
DPLL to a CRTC:

[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in dpll_hw_state.cfgcr1 (expected 0x80000168, found 0x000004a5)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in base.adjusted_mode.crtc_clock (expected 108000, found 49500)
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in port_clock (expected 108000, found 49500)

This usually ends up causing blank monitors, since the DPLL never can
get set to the right clock.

Fixes: 086f8e84 ("drm/i915: Prefix raw register defines with underscore")
Signed-off-by: NLyude <cpaul@redhat.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454600601-21900-1-git-send-email-cpaul@redhat.com

RC6 setup is shared between BIOS and Driver. BIOS sets up subset of RC6
setup registers. If those are not setup Driver should not enable RC6.
For implementing this, driver can check RC_CTRL0 and RC_CTRL1 values
to know if BIOS has enabled HW/SW RC6.
This will also enable user to control RC6 using BIOS settings alone.
RC6 related instability can be avoided by disabling via BIOS settings
till driver fixes it.

v2: Had placed logic in gen8 function by mistake. Fixed it.
Ensuring RPM is not enabled in case BIOS disabled RC6.

v3: Need to disable RPM if RC6 is disabled due to BIOS settings. (Daniel)
Runtime PM enabling happens before gen9_enable_rc6.
Moved the updation of enable_rc6 parameter in intel_uncore_sanitize.

v4: Added elaborate check for BIOS RC6 setup. Prepared check_pctx for bxt.
    (Imre)

v5: Caching reserved stolen base and size in the driver private data.
    Reorganized RC6 setup check. Moved from gen9_enable_rc6 to
    intel_uncore_sanitize. (Imre)

v6: Rebasing on the patch submitted by Imre that moves gem_init_stolen
    earlier in the load.

v7: Removed PWRCTX_MAXCNT_VCSUNIT1 check as it applies to SKL. (Imre)

v8: Fixed formatting and checkpatch issues. Fixed functional issue where
    RC6 ctx size check was missing. (Imre)

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454697809-22113-1-git-send-email-sagar.a.kamble@intel.com

Make the gpio read/write functions more generic iosf sideband read/write
functions, taking the iosf port as argument.

v2: rebase
v3: rebase
v4 by Jani: address Ville's review
v5 by Jani: drop the PCI_DEVFN change (Ville)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454604915-17142-1-git-send-email-jani.nikula@intel.com

Not needed.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/532150999335216b1374c606e1b3c253a6c9fe9d.1454582914.git.jani.nikula@intel.com

Make it easier to spot duplicates.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/a89f10d2d1954ac1b9a278534cb5209973354caa.1454582914.git.jani.nikula@intel.com

WaIncreaseDefaultTLBEntries increases the number of TLB
entries available for GPGPU workloads and gives significant
( > 10% ) performance gain for some OCL benchmarks.
Put this in a new function that can be a place for
workarounds that are GT related but not required per ring.
This function is called on driver load and also after a
reset and on resume, so it is safe for workarounds that get
clobbered in these situations. This function currently has
just this one workaround.

v2: This was originally split into 3 patches but following
  review feedback was squashed into 1.
  I have not incorporated some style comments from Chris
  Wilson as I felt that after defining and intialising a
  temporary variable and then adding an additional if block
  to only write the register if the temporary variable had
  been set, this didn't really give a net gain.

v3: Resending in the hope that BAT will run

v4: Change subject line to trigger BAT (please!)
Signed-off-by: NTim Gore <tim.gore@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454586574-2343-1-git-send-email-tim.gore@intel.com

On SKL and KBL we can have pipe A/B/C disabled by fuse settings. The
pipes must be fused in descending order (e.g. C, B+C, A+B+C). We simply
decrease info->num_pipes if we find a valid fused out config.

v2: Don't store the pipe disabled mask in device info (Damien)

v3: Don't check FUSE_STRAP register for pipe c disabled

Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[Jani: fixed some checkpatch indentation complaints]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453300280-10661-1-git-send-email-patrik.jakobsson@linux.intel.com

Per context preemption granularity control is only available from SKL:E0+

Actual WA is to disable percontext preemption granularity control until D0
which is the default case so this is equivalent to the inverse of
WaDisablePerCtxtPreemptionGranularityControl:skl

v2: add some detail to commit msg (Chris)
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-8-git-send-email-arun.siluvery@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Required for,
WaDisableObjectLevelPreemptionForTrifanOrPolygon:bxt
WaDisableObjectLevelPreemptionForInstancedDraw:bxt
WaDisableObjectLevelPreemtionForInstanceId:bxt

According to WA database these are only applicable for BXT:A0 but since
A0 and A1 shares the same GT these are extended for A1 as well.

These are also required for SKL until B0 but not adding them because they
are pre-production steppings.

This register is added to HW whitelist to support WA required for future
enabling of pre-emptive command execution, WA implementation will be in
userspace and it cannot program this register if it is not on HW whitelist.

v2: use lower case in register defines (Nick)
v3: explain purpose of changes (Chris)
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-5-git-send-email-arun.siluvery@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Required for WaAllowUMDToModifyHDCChicken1:skl,bxt

This register is added to HW whitelist to support WA required for future
enabling of pre-emptive command execution, WA implementation will be in
userspace and it cannot program this register if it is not on HW whitelist.

v2: explain purpose of changes (Chris)
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-4-git-send-email-arun.siluvery@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Required for WaEnablePreemptionGranularityControlByUMD:skl,bxt

This register is added to HW whitelist to support WA required for future
enabling of pre-emptive command execution, WA implementation will be in
userspace and it cannot program this register if it is not on HW whitelist.

v2: explain purpose of WA (Chris)
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-3-git-send-email-arun.siluvery@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some of the HW registers are privileged and cannot be written to from
non-privileged batch buffers coming from userspace unless they are added to
the HW whitelist. This whitelist is maintained by HW and it is different from
SW whitelist. Userspace need write access to them to implement preemption
related WA.

The reason for using this approach is, the register bits that control
preemption granularity at the HW level are not context save/restored; so even
if we set these bits always in kernel they are going to change once the
context is switched out.  We can consider making them non-privileged by
default but these registers also contain other chicken bits which should not
be allowed to be modified.

In the later revisions controlling bits are save/restored at context level but
in the existing revisions these are exported via other debug registers and
should be on the whitelist. This patch adds changes to provide HW with a list
of registers to be whitelisted. HW checks this list during execution and
provides access accordingly.

HW imposes a limit on the number of registers on whitelist and it is
per-engine.  At this point we are only enabling whitelist for RCS and we don't
foresee any requirement for other engines.

The registers to be whitelisted are added using generic workaround list
mechanism, even these are only enablers for userspace workarounds. But by
sharing this mechanism we get some test assets without additional cost (Mika).

v2: rebase

v3: parameterize RING_FORCE_TO_NONPRIV() as _MMIO() should be limited to
i915_reg.h (Ville), drop inline for wa_ring_whitelist_reg (Mika).

v4: improvements suggested by Chris Wilson.
Clarify that this is HW whitelist and different from the one maintained in
driver. This list is engine specific but it gets initialized along with other
WA which is RCS specific thing, so make it clear that we are not doing any
cross engine setup during initialization.
Make HW whitelist count of each engine available in debugfs.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NArun Siluvery <arun.siluvery@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453412634-29238-2-git-send-email-arun.siluvery@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Imre mentioned that chv might also have capability to
track unclaimed mmio accesses. Ville added that
both chv and vlv has this capability and he had already
made this way back [1]. Mimic what Ville's patch does
but adapt on top of less frequent mmio accesses by
omitting checking always on reg writes.

This patch is untested as of now.

v2: overflow handling and posting omitted (Ville)

References: [1] http://lists.freedesktop.org/archives/intel-gfx/2013-May/027599.html
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450201542-22918-1-git-send-email-mika.kuoppala@intel.com

DRM Docbook is now Markdown ready. This means its doc is able to
use markdown text on it.

* Documentation/DocBook/drm.tmpl: Contains a table duplicated from
  drivers/gpu/drm/i915/i915_reg.h. This is not needed anymore

* drivers/gpu/drm/drm_modeset_lock.c: had a code example that used
  to look pretty bad on html. Fixed by using proper code markup.

* drivers/gpu/drm/drm_prime.c: Remove spaces between lines to make
  a proper markup list.

* drivers/gpu/drm/i915/i915_reg.h: Altought pandoc supports tables,
  it doesn't support table cell spanning. But we can use fixed-width
  for those special cases.

* include/drm/drm_vma_manager.h: Another code example that should be
  proper indented with four spaces.

v2 (Daniel): Adjust name to gpu.xml due to rename.

v3 (Daniel):
Split out the actual enabling in the Makefile - this way we can merge
the conversion, while just keeping the enabling in a drm-private tree.

Signed-off-by: Danilo Cesar Lemes de Paula <danilo.cesar@collabora.co.uk> (v1)
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Acked-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448471279-19748-2-git-send-email-daniel.vetter@ffwll.ch

Pipe is assigned based on the port, but it should be
based on current crtc. Correcting the same in this patch.

v2: Use macro BXT_PIPE_SELECT(pipe) (Daniel)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we want to use SPLL for FDI we want SSC, which means we have to
disable clock bending for the PCH SSC reference (bend and spread are
mutually exclusive). So let's turn off bending when we want spread.
In case the BIOS enabled clock bending for some reason we'll just turn
it off and enable the spread mode instead.

Not sure what happens if the BIOS is actually using the bend source for
HDMI at this time, but I suppose it should be no worse than what already
happens when we simply turn on the spread.

We don't currently use the bend source for anything, and only use the
PCH SSC reference for the SPLL to drive FDI (always with spread).

v2: Fix the %5 vs %10 fumble for SSCDITHPHASE (Paulo)
    Add 'WARN_ON(steps % 5 != 0)' sanity check (Paulo)
    Fix typos in commit message (Paulo)

Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449260379-14093-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

The reference clock for BXT is 19.2 MHz not 19.5 MHz, updating the
correct value here.
Signed-off-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449238659-12473-2-git-send-email-m.deepak@intel.com

LPT-H has a strap bit for fused off CRT block. Check it to see if
we should register the CRT connector or not. Supposedly this also
forces the ADAP enable bit to 0, so the detection we added in
commit 6c03a6bd ("drm/i915: Don't register CRT connector when it's fused off")
should already catch it, but checking the fuse bit should at least
do no harm.

v2: Use HAS_PCH_LPT_H() (Paulo)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449005335-15192-1-git-send-email-ville.syrjala@linux.intel.com

Per bspec, "Backlight PWM may stop in the asserted state, causing
backlight to stay fully on. WA: Before disabling PWM, set CLKGATE_DIS_0
0x46530 bit 13 PWM1 Gating Dis (for PWM1) or bit 14 PWM2 Gating Dis (for
PWM2). The bits can remain set without harm." (There's no workaround
name for this.)

This fixes some Broxton backlight issues.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[Jani: cleanup & commit message]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448958232-26520-3-git-send-email-jani.nikula@intel.com

Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.

This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.

The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.

As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
  lea    0x70024(%rdx,%rax,1),%r9d
  mov    $0x1,%edx
- movslq %r9d,%r9
- mov    %r9,%rsi
- mov    %r9,-0x58(%rbp)
- callq  *0xd8(%rbx)
+ mov    %r9d,%esi
+ mov    %r9d,-0x48(%rbp)
 callq  *0xd8(%rbx)

So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.

v2: i915_mmio_reg_{offset,equal,valid}() helpers added
    s/_REG/_MMIO/ in the register defines
    mo more switch statements left to worry about
    ring_emit stuff got sorted in a prep patch
    cmd parser, lrc context and w/a batch buildup also in prep patch
    vgpu stuff cleaned up and moved to a prep patch
    all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-29-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

The logical render context population has a bunch of raw ring register
offsets. Use the names we have for them, and in cases where we we don't,
give them names.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-23-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Add defines for the upper halves of the registers used by the cmd
parser. Getting rid of the arithmetic with the register offset
will help in making registers type safe.

v2: s/_HI/_UDW/ (Chris)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1446839080-18732-1-git-send-email-ville.syrjala@linux.intel.com