this patch fixes following sparse warning:
ts3a227e.c:222:5: warning: symbol 'ts3a227e_enable_jack_detect' was not declared. Should it be static?
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Reported by Coverity: CID 1267985 CID 1267986

Fix these two Defects: Uninitialized scalar variable.
Signed-off-by: NJie Yang <yang.jie@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The intercon_extra_3104 is obviously for tlv320aic3104.
Reported-by: NBenoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

To quote from section 1.3.1 of the data sheet:
	The SGTL5000 has an internal reset that is deasserted
	8 SYS_MCLK cycles after all power rails have been brought
	up. After this time, communication can start

	...
	1.0us represents 8 SYS_MCLK cycles at the minimum 8.0 MHz SYS_MCLK.
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Disables GPIO support and LINE2 input and renames Mic3 input to Mic2,
if tlv320aic3104 mode is seleced. Devicetree binding document is
updated accordingly.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Instead of calling device_create_file() manually, assign the static
attribute group entries at the device registration.  This simplifies
the error handling and avoids the possible races.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Added entry in sst driver to support rt5645 codec
for intel Braswell platform.
Signed-off-by: NFang, Yang A <yang.a.fang@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas R-Car sound driver doesn't call
snd_soc_unregiter_component/platform() in .remove.
This patch call these functions.
Reported-by: NNguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: NBui Duc Phuc <bd-phuc@jinso.co.jp>
Reported-by: NCao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas R-Car sound driver is using snd_ctl_xxx()
functions, but it didn't call snd_ctl free_one() / snd_ctl_remove().
This patch call these functions.
Reported-by: NNguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: NBui Duc Phuc <bd-phuc@jinso.co.jp>
Reported-by: NCao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

One of the McASP instances in DM646x line of DMSoC only supports DIT mode.
This means that the given IP does not have support for rx and all the rx
related resources are missing, like irq and DMA request.
The driver should not fail if any or all  of the RX resource is missing
when the op_mode is set to DIT mode.
Since RX is not possible in DIT mode, we can just ignore the rx resources
when the McASP is used in DIT mode.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

On DA830 devices McASP0,1 and 2 shares a single combined interrupt request
line.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

There is no need for them to be included.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The machine driver has no business with the underlying dma.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

As DMA framework request DMA using direction only in prep_slave
function, (The At91 xdma driver has adapted to this request).
So won't check direction when do DMA configuration.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Only using PDC, it needs to clean PDC registers.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

In startup function, enable ssc clock and in shutdown function,
disable clock. And also remove disable ssc in shutdown function,
as ssc is disabled in prepare function.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

When SCC work in DSP A mode, the data outputs/inputs are shift out on
falling edge, the frame sync are sample on the rising edge.
Reported-by: NSongjun Wu <songjun.wu@atmel.com>
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Shift the I2S mode value by the necessary amount before writing the
registers. This makes Right Justified and PCM mode work in addition to
the default Left Justified mode.
Signed-off-by: NFilip Brozovic <fbrozovic@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Fix the issue introduced by:
36849409 ASoC: tlv320aic3x: Add TDM support

The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.

Fixes: 36849409 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

"Mic Bias" is DAPM_SUPPLY so it has to be connected in the route
accordingly.
Fixes audio capture on the board.
Reported-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NMark Brown <broonie@kernel.org>

In a rare combination of Kconfig settings, the 88pm860x-codec
module may be selected as a loadable module, while it's also being
used by the ttb-dkb code that is built-in, resulting in a link
error:

sound/built-in.o: In function `ttc_pm860x_init':
:(.text+0x3e888): undefined reference to `pm860x_hs_jack_detect'
:(.text+0x3e898): undefined reference to `pm860x_mic_jack_detect'

Changing ttb-tkb to a tristate option tells Kconfig that 88pm86x
actually needs to be built-in if ttc-dkb is also built-in.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NPeter Rosin <peda@axentia.se>
Acked-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This was overlooked in the late change to remove the I2S padding bits
from S24_LE mode. The patch also limits S32_LE mode to 384kHz, the
maximum according to the datasheets.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

The rt5677 codec has gained code that requires SPI to work correctly,
but there is no provision in Kconfig to prevent the driver from
being used when SPI is disabled or a loadable module, resulting
in this build error:

sound/built-in.o: In function `rt5677_spi_write':
:(.text+0xa7ba0): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
:(.init.text+0x253c): undefined reference to `spi_register_driver'

ERROR: "spi_sync" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!
ERROR: "spi_register_driver" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined!

This makes the SPI portion of the driver depend on the SPI subsystem,
and disables the function that uses SPI for firmware download if SPI
is disabled. The latter may not be the correct solution, but I could
not come up with a better one.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: af48f1d0 ("ASoC: rt5677: Support DSP function for VAD application")
Signed-off-by: NMark Brown <broonie@kernel.org>

An earlier bug fix of mine made the SND_DM365_VOICE_CODEC symbol
tristate to avoid creating an undefined reference from the
davinci-vcif.c driver to the davinci_soc_platform_register
function that may be in a module.

However, this may now lead to a different error on randconfig
kernels:

"warning: SND_DM365_VOICE_CODEC creates inconsistent choice state"

This happens because we now have a choice statement with
one bool and one tristate option, and the latter might not
support being set to 'y' because of dependencies.

This new change turns the other option into 'tristate' as well,
which avoids the problem.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 19926c6d ("ASoC: davinci: vcif must be a module if SND_DAVINCI_SOC is")
Signed-off-by: NMark Brown <broonie@kernel.org>

The WM8904 and WM8918 has the same data type, while the WM8912
has different data type. So, use the data in dt ids table to
distinguish them.
Signed-off-by: NAlexander Morozov <linux@meltdown.ru>
[voice.shen@atmel.com: add code to distinguish device type]
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

The PLL introduces jitter, which in turn introduces noice if used
to clock the DAC. Thus, avoid the PLL output, and use the PLL input
to drive the DAC clock, if possible.

This is described for the PCM5142/PCM5242 chips in the answers to the
forum post "PCM5142/PCM5242 DAC clock source" at the TI E2E community
pages (1).

(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/389994Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Using the PLL in master mode requires using an external connection
between one of the GPIO pins (configured as PLL/4 output) and the
SCK pin. It also requires the external clock to be fed to some other
GPIO pin instead of the SCK pin.

This is described for the PCM5122 chip in the answers to the forum post
"PCM5122 DAC as I2S master troubles with PLL mode" at the TI E2E
community pages (1). The clocking functionality is also much better
described in the datasheet for the chip PCM5242, which seems to be
register compatible with PCM512x and PCM514x (which both have severely
lacking datasheets).

(1) http://e2e.ti.com/support/data_converters/audio_converters/f/64/t/267830Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Use register field names from the seemingly compatible PCM5242 datasheet,
as the PCM512x and PCM514x datasheets are severly lacking.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NMark Brown <broonie@kernel.org>

of_match_ptr is already conditionally compiled based on
CONFIG_OF so further conditional compilation is not
required.  Remove conditional compilation surrounding
of_match_ptr.
Signed-off-by: NAndrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We never set the ->scratch pointer, so let's delete it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch fix warning while "make xmldocs".

Warning(.//sound/soc/soc-devres.c:70): No description
 found for parameter 'platform_drv'
Warning(.//sound/soc/soc-devres.c:70): Excess function
 parameter 'platform' description in 'devm_snd_soc_register_platform'
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds support for rt5650 codec.
Signed-off-by: NBard Liao <bardliao@realtek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

We need hold lock each time updating shirm registers, otherwise,
we may set unexpected values to them when they are set in
different thread at different time sequence.

The notification work will be scheduled in global work queue,
which won't hold this sst->spinlock itself, so here we need
change to use the lock version to update shim registers.
Signed-off-by: NJie Yang <yang.jie@intel.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The voltage controls key press threshold.
Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

ts3a227e datasheet says typical key resistance is
  key1 50 Ohm
  key2 135 Ohm
  key3 240 Ohm
  key4 470 Ohm

The android headset specification expect buttons impedance:
  A (MEDIA) 0-70 Ohm
  D (VOICECOMMAND) 110-180 Ohm
  B (VOLUMEUP) 210-290 Ohm
  C (VOLUMEDOWN) 360-680 Ohm

Thus key mapping should be
  key1 - MEDIA
  key2 - VOICECOMMAND
  key3 - VOLUMEUP
  key3 - VOLUMEDOWN
Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

The I2C init path forgot to init the mutex, leading to an oops when
controls are accessed.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org