The commit that went into 3.17:

    ath9k: Summarize hw state per channel context

    Group and set hw state (opmode, primary_sta, beacon conf) per
    channel context instead of whole list of vifs. This would allow
    each channel context to run in different mode (STA/AP).
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

broke multi-vif configuration due to not properly calculating
the bssid mask.

The test case that caught this was:

 create wlan0 and sta0-4 (6 total), not sure how much that matters.
 associate all 6 (works fine)
 disconnect 5 of them, leaving sta0 up
 Start trying to bring up the other 5 one at a time.  It will
 fail, with iw events looking like this (in these logs, several
 sta are trying to come up, but symptom is the same with just one)

The patch causing the regression made quite a few changes, but
the part I think caused this particular problem was not
recalculating the bssid mask when adding and removing interfaces.

Re-adding those calls fixes my test case.  Fix bad comment
as well.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.

Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.

Cc: stable@vger.kernel.org
Signed-off-by: NMiaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function chandef_to_chanspec() failed when converting a
chandef with bandwidth set to NL80211_CHAN_WIDTH_20_NOHT. This
was reported by user running the device in AP mode.

------------[ cut here ]------------
WARNING: CPU: 0 PID: 304 at
	drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:381
		chandef_to_chanspec.isra.11+0x158/0x184()

Modules linked in:

CPU: 0 PID: 304 Comm: hostapd Not tainted 3.16.0-rc7-abb+g64aa90f2 #8

[<c0014bb4>] (unwind_backtrace) from [<c0012314>] (show_stack+0x10/0x14)
[<c0012314>] (show_stack) from [<c001d3f8>] (warn_slowpath_common+0x6c/0x8c)
[<c001d3f8>] (warn_slowpath_common) from [<c001d4b4>] (warn_slowpath_null+0x1c/0x24)
[<c001d4b4>] (warn_slowpath_null) from [<c03449a4>] (chandef_to_chanspec.isra.11+0x158/0x184)
[<c03449a4>] (chandef_to_chanspec.isra.11) from [<c0348e00>] (brcmf_cfg80211_start_ap+0x1e4/0x614)
[<c0348e00>] (brcmf_cfg80211_start_ap) from [<c04d1468>] (nl80211_start_ap+0x288/0x414)
[<c04d1468>] (nl80211_start_ap) from [<c043d144>] (genl_rcv_msg+0x21c/0x38c)
[<c043d144>] (genl_rcv_msg) from [<c043c740>] (netlink_rcv_skb+0xac/0xc0)
[<c043c740>] (netlink_rcv_skb) from [<c043cf14>] (genl_rcv+0x20/0x34)
[<c043cf14>] (genl_rcv) from [<c043c0a0>] (netlink_unicast+0x150/0x20c)
[<c043c0a0>] (netlink_unicast) from [<c043c4b8>] (netlink_sendmsg+0x2b8/0x398)
[<c043c4b8>] (netlink_sendmsg) from [<c04066a4>] (sock_sendmsg+0x84/0xa8)
[<c04066a4>] (sock_sendmsg) from [<c0407c5c>] (___sys_sendmsg.part.29+0x268/0x278)
[<c0407c5c>] (___sys_sendmsg.part.29) from [<c0408bdc>] (__sys_sendmsg+0x4c/0x7c)
[<c0408bdc>] (__sys_sendmsg) from [<c000ec60>] (ret_fast_syscall+0x0/0x44)
---[ end trace 965ee2158c9905a2 ]---

Cc: stable@vger.kernel.org # v3.17
Reported-by: NPontus Fuchs <pontusf@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NDaniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.

For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.

Patch fixes skb_under_panic problems reported from time to time:

https://bugzilla.kernel.org/show_bug.cgi?id=84911
https://bugzilla.kernel.org/show_bug.cgi?id=72471
http://marc.info/?l=linux-wireless&m=139108549530402&w=2
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591

Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:

	if (payload_length && payload_align > header_align)
		header_align += 4;

but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: NAntti S. Lankila <alankila@bel.fi>
Debugged-by: NAntti S. Lankila <alankila@bel.fi>
Reported-by: NHenrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-for-john-2014-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Emmanuel Grumbach <egrumbach@gmail.com> says:

"Two fixes here - we weren't updating mac80211 if a scan
was cut short by RFKILL which confused cfg80211. As a
result, the latter wouldn't allow to run another scan.
Liad fixes a small bug in the firmware dump."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.

Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2c ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This code existed but not for all the different FW APIs
we support.
Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

phy_read and phy_write are not set for every phy any more sine this:
commit d342b95d
Author: Rafał Miłecki <zajec5@gmail.com>
Date:   Thu Jul 31 21:59:43 2014 +0200

    b43: don't duplicate common PHY read/write ops

b43_phy_copy() accesses phy_read and phy_write directly and will fail
with some phys. This patch fixes the regression by using the
b43_phy_read() and b43_phy_write() functions which should be used for
read and write access.

This should fix this bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=87731Reported-by: NVolker Kempter <v.kempter@pe.tu-clausthal.de>
Tested-by: NVolker Kempter <v.kempter@pe.tu-clausthal.de>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Changes in the vendor driver were added to rtlwifi, but some updates
to rtl8192se were missed, and the driver could neither scan nor connect.
There are other changes that will enhance performance, but this minimal
set fix the basic functionality.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are typos in the handling of the descriptor pointers where the wrong
descriptor is referenced. There is also an error in which the pointer is
incremented twice.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Device RTL8192EE uses a new form of trx flow. This fix sets up the descriptors
correctly.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge tag 'mac80211-for-john-2014-11-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg <johannes@sipsolutions.net> says:

"This has just one fix, for an issue with the CCMP decryption
that can cause a kernel crash. I'm not sure it's remotely
exploitable, but it's an important fix nonetheless."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 7ec7c4a9 (mac80211: port CCMP to
cryptoapi's CCM driver) introduced a regression when decrypting empty
packets (data_len == 0). This will lead to backtraces like:

(scatterwalk_start) from [<c01312f4>] (scatterwalk_map_and_copy+0x2c/0xa8)
(scatterwalk_map_and_copy) from [<c013a5a0>] (crypto_ccm_decrypt+0x7c/0x25c)
(crypto_ccm_decrypt) from [<c032886c>] (ieee80211_aes_ccm_decrypt+0x160/0x170)
(ieee80211_aes_ccm_decrypt) from [<c031c628>] (ieee80211_crypto_ccmp_decrypt+0x1ac/0x238)
(ieee80211_crypto_ccmp_decrypt) from [<c032ef28>] (ieee80211_rx_handlers+0x870/0x1d24)
(ieee80211_rx_handlers) from [<c0330c7c>] (ieee80211_prepare_and_rx_handle+0x8a0/0x91c)
(ieee80211_prepare_and_rx_handle) from [<c0331260>] (ieee80211_rx+0x568/0x730)
(ieee80211_rx) from [<c01d3054>] (__carl9170_rx+0x94c/0xa20)
(__carl9170_rx) from [<c01d3324>] (carl9170_rx_stream+0x1fc/0x320)
(carl9170_rx_stream) from [<c01cbccc>] (carl9170_usb_tasklet+0x80/0xc8)
(carl9170_usb_tasklet) from [<c00199dc>] (tasklet_hi_action+0x88/0xcc)
(tasklet_hi_action) from [<c00193c8>] (__do_softirq+0xcc/0x200)
(__do_softirq) from [<c0019734>] (irq_exit+0x80/0xe0)
(irq_exit) from [<c0009c10>] (handle_IRQ+0x64/0x80)
(handle_IRQ) from [<c000c3a0>] (__irq_svc+0x40/0x4c)
(__irq_svc) from [<c0009d44>] (arch_cpu_idle+0x2c/0x34)

Such packets can appear for example when using the carl9170 wireless driver
because hardware sometimes generates garbage when the internal FIFO overruns.

This patch adds an additional length check.

Cc: stable@vger.kernel.org
Fixes: 7ec7c4a9 ("mac80211: port CCMP to cryptoapi's CCM driver")
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NRonald Wahl <ronald.wahl@raritan.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Merge tag 'mac80211-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg <johannes@sipsolutions.net> says:

"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-for-john-2014-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Emmanuel Grumbach <egrumbach@gmail.com> says:

"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.

Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.

This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231

CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.

Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.

Cc: stable@vger.kernel.org
Reported-by: NYosef Khyal <yosefx.khyal@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

An error in the code makes the allocated space for firmware to be too
small.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new version of rtlwifi needs code in rtl92ce_get_desc() that returns
the buffer address for read operations.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new version of rtlwifi needs code in rtl92se_get_desc() that returns
the buffer address for read operations.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver rtlwifi has been modified to call ieee80211_register_hw()
from the probe routine; however, the existing call in the callback
routine for deferred firmware loading was not removed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent changes in checking for Bluetooth status added some callbacks to code
in rtlwifi. To make certain that all callbacks are defined, a dummy routine has been
added to rtlwifi, and the drivers that need to use it are modified.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During 11n RX reordering, if there is a hole in RX table,
driver will not send packets to kernel until the rxreorder
timer expires or the table is full.
However, currently driver always restarts rxreorder timer when
receiving a packet, which causes the timer hardly to expire.
So while connected with to 11n AP in a busy environment,
ping packets may get blocked for about 30 seconds.

This patch fixes this timer restarting by ensuring rxreorder timer
would only be restarted either timer is not set or start_win
has changed.
Signed-off-by: NChin-Ran Lo <crlo@marvell.com>
Signed-off-by: NPlus Chen <pchen@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The right shift operation has higher precedence than the mask so we
left shift by "(i * 3)" and then immediately right shift by "(i * 3)"
then we mask.  It should be left shift, mask, and then right shift.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle

References: https://bugs.debian.org/766802Reported-by: NMartin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: NCyril Brulebois <kibi@debian.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface is deleted, an ongoing hardware scan is canceled and
the driver must abort the scan, at the very least reporting completion
while the interface is removed.

However, if it scheduled the work that might only run after everything
is said and done, which leads to cfg80211 warning that the scan isn't
reported as finished yet; this is no fault of the driver, it already
did, but mac80211 hasn't processed it.

To fix this situation, flush the delayed work when the interface being
removed is the one that was executing the scan.

Cc: stable@vger.kernel.org
Reported-by: NSujith Manoharan <sujith@msujith.org>
Tested-by: NSujith Manoharan <sujith@msujith.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Due to the time it takes to process the beacon that started the CSA
process, we may be late for the switch if we try to reach exactly
beacon 0.  To avoid that, use count - 1 when calculating the switch time.

Cc: stable@vger.kernel.org
Reported-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If we are switching from an HT40+ to an HT40- channel (or vice-versa),
we need the secondary channel offset IE to specify what is the
post-CSA offset to be used.  This applies both to beacons and to probe
responses.

In ieee80211_parse_ch_switch_ie() we were ignoring this IE from
beacons and using the *current* HT information IE instead.  This was
causing us to use the same offset as before the switch.

Fix that by using the secondary channel offset IE also for beacons and
don't ever use the pre-switch offset.  Additionally, remove the
"beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not
needed anymore.

Cc: stable@vger.kernel.org
Reported-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Userspace can add keys to an AP mode interface before start_ap has been
called. If there have been no calls to start_ap/stop_ap in the mean
time, the keys will still be around when the interface is brought down.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[adjust comments, fix AP_VLAN case]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The driver is not released when ieee80211_register_hw fails in
mac80211_hwsim_create_radio, leading to the access to the unregistered (and
possibly freed) device in platform_driver_unregister:

[    0.447547] mac80211_hwsim: ieee80211_register_hw failed (-2)
[    0.448292] ------------[ cut here ]------------
[    0.448854] WARNING: CPU: 0 PID: 1 at ../include/linux/kref.h:47 kobject_get+0x33/0x50()
[    0.449839] CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00001-gdd46990-dirty #2
[    0.450813] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.451512]  00000000 00000000 78025e38 7967c6c6 78025e68 7905e09b 7988b480 00000000
[    0.452579]  00000001 79887d62 0000002f 79170bb3 79170bb3 78397008 79ac9d74 00000001
[    0.453614]  78025e78 7905e15d 00000009 00000000 78025e84 79170bb3 78397000 78025e8c
[    0.454632] Call Trace:
[    0.454921]  [<7967c6c6>] dump_stack+0x16/0x18
[    0.455453]  [<7905e09b>] warn_slowpath_common+0x6b/0x90
[    0.456067]  [<79170bb3>] ? kobject_get+0x33/0x50
[    0.456612]  [<79170bb3>] ? kobject_get+0x33/0x50
[    0.457155]  [<7905e15d>] warn_slowpath_null+0x1d/0x20
[    0.457748]  [<79170bb3>] kobject_get+0x33/0x50
[    0.458274]  [<7925824f>] get_device+0xf/0x20
[    0.458779]  [<7925b5cd>] driver_detach+0x3d/0xa0
[    0.459331]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.459927]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.460660]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.461248]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.461824]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.462507]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.463161]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.463758]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.464393]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.465001]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.465569]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.466345]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.466972]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.467546]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.468072]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.468658]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.469303]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.469829] ---[ end trace ad8ac403ff8aef5c ]---
[    0.470509] ------------[ cut here ]------------
[    0.471047] WARNING: CPU: 0 PID: 1 at ../kernel/locking/lockdep.c:3161 __lock_acquire.isra.22+0x7aa/0xb00()
[    0.472163] DEBUG_LOCKS_WARN_ON(id >= MAX_LOCKDEP_KEYS)
[    0.472774] CPU: 0 PID: 1 Comm: swapper Tainted: G        W      3.17.0-00001-gdd46990-dirty #2
[    0.473815] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.474492]  78025de0 78025de0 78025da0 7967c6c6 78025dd0 7905e09b 79888931 78025dfc
[    0.475515]  00000001 79888a93 00000c59 7907f33a 7907f33a 78028000 fffe9d09 00000000
[    0.476519]  78025de8 7905e10e 00000009 78025de0 79888931 78025dfc 78025e24 7907f33a
[    0.477523] Call Trace:
[    0.477821]  [<7967c6c6>] dump_stack+0x16/0x18
[    0.478352]  [<7905e09b>] warn_slowpath_common+0x6b/0x90
[    0.478976]  [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00
[    0.479658]  [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00
[    0.480417]  [<7905e10e>] warn_slowpath_fmt+0x2e/0x30
[    0.480479]  [<7907f33a>] __lock_acquire.isra.22+0x7aa/0xb00
[    0.480479]  [<79078aa5>] ? sched_clock_cpu+0xb5/0xf0
[    0.480479]  [<7907fd06>] lock_acquire+0x56/0x70
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<79682d11>] mutex_lock_nested+0x61/0x2a0
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<7925b5e8>] driver_detach+0x58/0xa0
[    0.480479]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.480479]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.480479]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.480479]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.480479]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.480479]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.480479]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.480479]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.480479]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.480479]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.480479]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.480479]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.480479]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.480479]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.480479]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.480479]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.480479]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.480479] ---[ end trace ad8ac403ff8aef5d ]---
[    0.495478] BUG: unable to handle kernel paging request at 00200200
[    0.496257] IP: [<79682de5>] mutex_lock_nested+0x135/0x2a0
[    0.496923] *pde = 00000000
[    0.497290] Oops: 0002 [#1]
[    0.497653] CPU: 0 PID: 1 Comm: swapper Tainted: G        W      3.17.0-00001-gdd46990-dirty #2
[    0.498659] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.499321] task: 78028000 ti: 78024000 task.ti: 78024000
[    0.499955] EIP: 0060:[<79682de5>] EFLAGS: 00010097 CPU: 0
[    0.500620] EIP is at mutex_lock_nested+0x135/0x2a0
[    0.501145] EAX: 00200200 EBX: 78397434 ECX: 78397460 EDX: 78025e70
[    0.501816] ESI: 00000246 EDI: 78028000 EBP: 78025e8c ESP: 78025e54
[    0.502497]  DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
[    0.503076] CR0: 8005003b CR2: 00200200 CR3: 01b9d000 CR4: 00000690
[    0.503773] Stack:
[    0.503998]  00000000 00000001 00000000 7925b5e8 78397460 7925b5e8 78397474 78397460
[    0.504944]  00200200 11111111 78025e70 78397000 79ac9d74 00000001 78025ea0 7925b5e8
[    0.505451]  79ac9d74 fffffffe 00000001 78025ebc 7925a3ff 7a251398 78025ec8 7925bf80
[    0.505451] Call Trace:
[    0.505451]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.505451]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.505451]  [<7925b5e8>] driver_detach+0x58/0xa0
[    0.505451]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.505451]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.505451]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.505451]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.505451]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.505451]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.505451]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.505451]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.505451]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.505451]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.505451]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.505451]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.505451]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.505451]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.505451]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.505451]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.505451]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.505451] Code: 89 d8 e8 cf 9b 9f ff 8b 4f 04 8d 55 e4 89 d8 e8 72 9d 9f ff 8d 43 2c 89 c1 89 45 d8 8b 43 30 8d 55 e4 89 53 30 89 4d e4 89 45 e8 <89> 10 8b 55 dc 8b 45 e0 89 7d ec e8 db af 9f ff eb 11 90 31 c0
[    0.505451] EIP: [<79682de5>] mutex_lock_nested+0x135/0x2a0 SS:ESP 0068:78025e54
[    0.505451] CR2: 0000000000200200
[    0.505451] ---[ end trace ad8ac403ff8aef5e ]---
[    0.505451] Kernel panic - not syncing: Fatal exception

Fixes: 9ea92774 ("mac80211_hwsim: Register and bind to driver")
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJunjie Mao <eternal.n08@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mvm->cur_ucode wasn't set before we actually load the
firmware. This caused issues when we boot in RFKILL since
we get an RFKILL interrupt upon boot even before we load
any firmware.
This leads to issues since iwl_mvm_set_hw_rfkill_state
(the RFKILL interrupts handler in mvm) relies on this
variable.

Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Merge tag 'mac80211-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg <johannes@sipsolutions.net> says:

"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Emmanuel Grumbach <egrumbach@gmail.com> says:

"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.

Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit aa11bbf3.
This commit was causing connection issues and is not needed
if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default.

Regardless of the issues mentioned above, this patch added the
following WARNING:

WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]()
Got an HT rate for a non data frame 0x8
CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G           O   3.17.0+ #6
Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014
 0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52
 0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600
 0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020
Call Trace:
 [<ffffffff814fa911>] ? dump_stack+0x41/0x51
 [<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90
 [<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50
 [<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]
 [<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm]
 [<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm]
 [<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211]
 [<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211]
 [<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211]
 [<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0
 [<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0
 [<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0
 [<ffffffff8142f670>] ? ether_setup+0x70/0x70
 [<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110
 [<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40
 [<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0
 [<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60
 [<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0
 [<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180
 [<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70
 [<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f
---[ end trace cc19a150d311fc63 ]---

which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:

iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]

Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.

This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581

But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:

https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809

Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54 ("mac80211: add vif to flush call")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.

Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.

We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The probe requests sent during scan must get BT prio 3.
Fix that.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Cc: <stable@vger.kernel.org> [3.16+]
Fixes: 2adc8949 ("iwlwifi: mvm: BT Coex - fix boost register / LUT values")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>